Riello BeSMART Manual de usuario

EN Quick Start Guide

BeSMART Wi-Fi Thermostat

1The installation is made in 3 steps

B C

Install the BeSMART thermostat Install the Wi-Fi box Download the BeSMART App

Preparation

Before installation

•Refer to the appliance manual to ensure that the BeSMART thermostat is compatible with your

boiler

•The BeSMART wireless thermostat can be installed almost everywhere within the home, however

please refer to the adjacent diagrams for guidance when deciding on a suitable location.

•The BeSMART thermostat can also be used to replace an existing hard-wired thermostat (please

check appliance manual to ensure compatibility).

•Switch off and isolate the appliance and any external controls from the electrical supply, before

carrying out the installation.

Tools required for the installation

•Phillips screwdriver

•Small flat blade screwdriver

•Combination pliers

Avoid draughty areas Do not install above heat sources

Avoid direct sunlight Install at the correct height

BeSMART Installation

If necessary remove the old thermostat.

Attention: The BeSMART thermostat is a wireless

control. Isolate any redundant wiring and ensure it

does not interfere with the fitment of the BeSMART

control. If its intended to re-use any existing wiring; you

should refer to the appliance manual to ensure

compatibility .

Separate the BeSMART from the wall plate.

Fix the wall plate to the wall

using the supplied screws.

(screw head inside proper

location)

Hard-wired installation

If using as a hard-wired control; connect the respective wiring to

the relevant terminals on the BeSMART control.

ON/OFF

Attention: Please refer to the appliance

installation manual and the BeSMART

manual for specific information on hard-wired

connections.

BeSMART Installation

Re-attach the BeSMART thermostat to the wall plate by

aligning and then pressing firmly around the outer edges.

Attention: insert the batteries, observing

the correct polarity as indicated.

Insert two ‘AA’ type batteries

(supplied), into the battery compartment .

Wi-Fi Box Installation

In the case of a wireless BeSMART installation, connect the (supplied)

USB Wi-Fi Box cable to the boiler OT-Bus connection (for specific

boilers) or to the boiler room thermostat connection (TA or ON/OFF).

Attach the Wi-Fi Box to the appliance casing, using

the magnetic pad located on the rear of the Wi-Fi

Box. Please check the ambient temperature is

according the product specification as indicated in

the installation manual. In case of installation wireless,

low Wi-Fi signal and boiler RF receiver installed, place

the Wi-Fi Box in an ambient with a good Wi-Fi signal

(above 30%).

Attention: for the electrical connection and the technical specifications, please

refer to the installation manual. (OT PCB plug supplied as standard)

USB

For a wireless installation, insert the other end

of the USB cable into the OUTPUTS/BOILER

socket of the Wi-Fi Box.

USB

USB mini B

Using the mini USB cable

and power adaptor

(supplied); connect the Wi-Fi

box to an adjacent electrical

socket .

TA = Black

OT = Red

Outputs/Boiler

C Installation and configuration of smartphone app

Download and install the

BeSMART App on a

smartphone or tablet.

Create a user account

following the steps indicated on

the app.

Link the user account to the ‘ID

Wi-Fi’ code that’s located on

the side of the Wi-Fi Box.

MAC : 000000000000

ID Wi-Fi : 0000000000000

Use the password key of the ‘Wi-Fi’ router to link the Wi-Fi Box to the home network using one of the methods indicated below.

SmartLink:

Press once the SmartLink button with a paper clip or similar

The green LED should be flashing rapidly

Start the smart link function on the app (Wi-Fi configuration menu)

enter the network password – Wi-Fi Box will automatically configure

WPS: (only for router with WPS functionality)

Enable the WPS function via your router/home network

Press and hold the WPS button on the WiFi box with a paper clip or similar,

until the green and red LEDs are flashing rapidly and consecutively

Successful activation is confirmed when the red LED flashes rapidly

Outputs/Boiler

WPS / Smartlink

WPS / Smartlink Outputs/Boiler

If required, it is possible to couple a boiler receiver or additional thermostats to the Wi-Fi Box

using the following procedure: press and hold the Wi-Fi LED button on the Wi-Fi Box until both

red and green LEDs are flashing simultaneously. Place the device that is to be coupled, into

the ‘coupling’ mode. When the coupling process has been completed, the system will

automatically return to the normal operating condition.

Wi-Fi LED button

The system, once online, may take up to 4 minutes for self configuration

Restart Wi-Fi router at the end

Alarms and working status

Alarm codes indicated on the

BeSMART display and

suggested corrective actions.

More info and technical support on the following website:

www.besmart-home.com

BeSMART is a RIELLO GROUP brand

Via Ing. Pilade Riello, 7

37045 Legnago - Italy

Explanation of status LEDs displayed on Wi-Fi Box.

LED

 = fixed ON

 = flashing fast (0.5 secs)

 = flashing slow (1 secs)

Err

E82

E83

E84

A01….99

Temperature sensor broken.

(not reparable)

Radio frequency error.

(Batteries/distance)

NO OT-bus communication.

(check connections)

Hardware problem.

(not reparable)

Boiler alarm.

(refer to boiler manual)

LED

green

LED

red Status



Relay = bridged (only with ON/OFF installation)



Relay = open (only with ON/OFF installation)



OT-bus connection = OK (only with OT connection)





Boiler alarm (only with OT connection)







Network or RF error



WPS mode in progress (press and hold WPS button) – wait WPS signal



WPS signal detected



SmartLink mode in progress (press SmartLink button once)



RF encoding in progress (press and hold the Wi-Fi LED button)

Otros manuales para BeSMART

Otros manuales de Termostato de Riello

Riello

Riello CDI 15 Manual de usuario

Riello

Riello Hi, Comfort 100 Manual de operación e instalación

Riello

Riello ricloud Manual de usuario

Riello

Riello BeSMART Manual de usuario

Riello

Riello BeSMART Manual de operación e instalación

Riello

Riello Hi, Comfort T100 Manual de operación e instalación

Riello

Riello RiCLOUD NA Series Manual de usuario

Riello

Riello ricloud Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario