Riello P 200 T/G Guía de inicio rápido

Installation, use and maintenance instructions

2915906 (3) - 11/2012

Light oil burners

CODE MODEL TYPE

3477785 P200 T/G 477 T80

3477786 P200 T/G 477 T80

5906 1

TECHNICAL DATA

ELECTRICAL DATA

Motor IE1

Motor IE2

1- Suction line

2- Return line

3- Pump pressure adjustment screws

4- Manometer plug (G 1/8)

5- Vacuometer plug (G 1/2)

6- Reset push-button of the motor overload relay

7- Wiring terminal board

8- Control box reset push-button and lock-out lamp

Cable clamps

10 - Ignition transformer

11 - Regulating bush for combustion head

12 - Valves group with hydraulic jacks

13 - Electric board

Thermal power - Output 530 / 2370 kW - 45 / 200 kg/h (see page 2)

Operation 1st stage - 2nd stage - 3rd stage

Fuel Light oil, max. viscosity at 20° C: 6 mm2/s (1.5° E)

Electrical supply Three-phase 220V +10% -10% ~ 60Hz without neutral

380V +10% -10% ~ 60Hz with neutral

Motor 15.9 A / 220V - 9.2A / 380V

Ignition transformer Primary: 2 A - Secondary: 2x 6.5 kV - 35 mA

Absorbed electrical power 5.5 kW

Electrical supply Three-phase 220V +10% -10% ~ 60Hz without neutral

380V +10% -10% ~ 60Hz with neutral

Motor 14.6 A / 220V - 8.5A / 380V

Ignition transformer Primary: 2 A - Secondary: 2x 6.5 kV - 35 mA

Absorbed electrical power 5.5 kW

Fig. 1

Quantity Accessories

2 Flexibles tubes

2 Nipples

4Screws

1 Gasket for flange

4 Cable clamps

5906 2

DIMENSIONS (mm)

* It is possible with a spacer upon request.

OPERATION AND EFFICIENCY OF THE BURNER

ACCESSOIRES

RADIO DISTURBANCE PROTECTION KIT: Code 3010386

If the burner is installed in places particularly subject to radio disturbance (emission of signals exceeding 10 V/m) owing

tothepresenceofanINVERTER,orinapplications where the length of the thermostat connections exceeds 20 metres,

a protection kit is available as an interface between the control box and the burner.

1st STAGE

POWER AND OUTPUT

MINIMUM MAXIMUM

kW kg/h kW kg/h

1st nozzle: ignition phase 391 33 782 66

1st + 2nd nozzle: intermediate phase 794 67 1576 133

1st + 2nd + 3rd nozzle: operation phase 1186 100 2372 200

2nd STAGE

POWER AND OUTPUT

MINIMUM MAXIMUM

kW kg/h kW kg/h

1st nozzle: ignition phase 391 33 782 66

1st + 2nd nozzle: 1st stage of operation 794 67 1576 33

1st + 2nd + 3rd nozzle: 2nd stage of operation 1186 100 2372 200

3rd STAGE

POWER AND OUTPUT

MINIMUM MAXIMUM

kW kg/h kW kg/h

1st nozzle: 1st stage of operation 557 47 794 67

1st + 2nd nozzle: 2nd stage of operation 1067 90 1576 133

1st + 2nd + 3rd nozzle: 3rd stage of operation 1186 100 2372 200

Boiler front plate

drilling Burner

5906 3

COMBUSTION CHAMBER PRESSURE - MAXIMUM OUTPUT

(three nozzles in operation)

Operation field in accordance with DIN 4787

When the burner operates with only one, or two nozzles, the pressurization conditions are improved and no prob-

lems arise.

DIMENSIONS OF THE TESTING COMBUSTION CHAMBER

(in compliance with ISO 5063 - 1978)

For the combustion head projection carefully

follow the boiler manufacturer indications.

A proper protection with refractory material on

the combustion chamber shall be made, when

the boilers with frontal smoke box are used.

Testing thermal load

D = Boiler diameter in mm

P = Position of the mobile

movable wall (mm)

5906 4

SUPPLY LINE

NOTICE

Before placing the burner in operation, ensure that the return line is open.

Any obstruction may damage the pump seal.

Pump priming: Fill the pump with the light oil from the vacuometer plug (5) (fig. 1), put the burner in operation, purge

the air from the manometer plug (4) (fig. 1) and wait for the pump priming. If lock-out occurs repeat the procedure.

H= Difference in the pipes height L= Total length of the suction tube

øi = Internal diameter of the tube. Copper tubes ø 14 and 16 mm could be replaced by steel tubes G 1/2” and G 3/4”.

Pump priming: Loose the tap from the vacuometer

plug 5 (fig. 1) and wait for the flow of the fuel.

Pay attention to do not overcome the max. depression of 0.45 bar (35 cm Hg), over this

value the fuel may turn into gas.

Check the pipes are perfectly sealed.

When the fuel tank is under the burner level we suggest to let the return line arrive where

the suction line starts.

In this case the foot valve is not necessary.

Should the return line arrive over the fuel level, the foot valve is indispensable. Notice that

this solution is less safe than the previous one, because it is possible the valve has not a

good sealing.

meters L meters

I.D. 14 mm I.D. 16 mm

005

0,5 5 10

11020

1,5 20 40

23050

meters L meters

I.D. 14 mm I.D. 16 mm

0 50 100

0.5 40 80

13060

1.5 20 40

21020

3510

5906 5

INTERNAL WIRING DIAGRAM

(carried out by the factory)

KEY TO LAYOUT

CMV Fan motor contactor MB Wiring terminal board

CO Commutator MV Fan motor

FR Photocell RT Thermal relay

h 1 1 st stage hourcounter TA Ignition transformer

h 2 2 nd stage hourcounter TB Burner ground (earth) connection

h 3 3 rd stage hourcounter VS Safety solenoid valve

L1 1 st stage lamp V1 1 st stage solenoid valve

L2 2 nd stage lamp V2 2 nd stage solenoid valve

L3 3 rd stage lamp V3 3 rd stage solenoid valve

L4 Lock - out motor lamp

2567

5906 6

ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK

(to be carried out by the installer)

D2648

KEY TO LAYOUT

HRemote lock - out signal TL Load limit remote control system

I1 Burner manual stop switch TS Safety load control system

MB Wiring terminal board T2 2 nd stage load control system

PS Reset push - button T3 3 rd stage load control system

TB Burner ground (earth) connection

220V 380V

F Ampere T35 T25

S mm24,0 2,5

Check the lock-out by darkening the photo-cell after removal of the cover.

ATTENTION: HIGH VOLTAGE

Important:

In systems where the run of wiring connecting the thermostat exceeds 20 metres in length, or in places

where the burner is subject to particularly disturbing electromagnetic interference (over 10 v/m), you must

insert the relay-inter face kit item number 3010386.

Note:

5906 7

CHOICE OF: NOZZLES - PUMP PRESSURE -

COMBUSTION HEAD ADJUSTMENT

•State, first of all, the maximum output required with all three nozzles in operation.

•On the base of the maximum required output, choose-from table A or B - three related nozzles.

Nozzles: 60° - Pump pressure: 12 bar

For three-stage operation (up to 170 kg/h) 1st and 2nd nozzle are not equal to the 3rd one. Follow this procedure

in order to obtain higher values of CO2(during 1st and 2nd stage of operation), complying with German Standard

DIN.

•The references on the table C have to be followed in case of need of:

- modification of the pump pressure in order to vary the output;

- diverse composition of the 3 nozzles group;

- knowledge of the output in 1st and 2nd stage.

SUGGESTED NOZZLES

(1) The pump pressure is referred to all three nozzles operating, the pressure increases automatically with two noz-

zles in operation and more with only one.

1st Stage / 2nd Stage

ANozzles 60°

Pump 12 bar (1)

Total delivery

kg/h

GPH

1st 2nd 3rd 1st + 2nd + 3rd

8.00 8.00 8.00 102.90

8.30 8.30 8.30 106.80

8.50 8.50 8.50 109.50

9.00 9.00 9.00 115.80

9.50 9.50 9.50 122.40

10.00 10.00 10.00 128.70

10.50 10.50 10.50 135.30

11.00 11.00 11.00 141.60

12.00 12.00 12.00 154.50

13.00 13.00 13.00 167.40

13.80 13.80 13.80 177.60

14.00 14.00 14.00 180.30

15.00 15.00 15.00 193.20

15.30 15.30 15.30 197.10

3rd Stage

BNozzles 60°

Pump 12 bar (1)

Total delivery

kg/h

GPH

1st 2nd 3rd 1st + 2nd + 3rd

10.00 10.00 5.00 107.30

10.50 10.50 5.00 111.70

10.50 10.50 6.00 115.90

11.00 11.00 6.50 122.30

12.00 12.00 6.50 130.90

12.00 12.00 7.50 135.20

13.00 13.00 7.50 143.80

13.80 13.80 7.50 150.70

13.80 13.80 10.00 161.30

13.80 13.80 12.00 169.90

13.80 13.80 13.80 177.60

14.00 14.00 14.00 180.30

15.00 15.00 15.00 193.20

15.30 15.30 15.30 197.10

5906 8

Rated nozzles delivery are shown in the table.

The real nozzle delivery may vary from the rated one up to ± 5%, its detection is made by weighing the oil sprayed

out from the nozzle inserted in a tube.

The pump leaves the factory rated at 12 bar.

Pay attention to not overcome the pump pressure values of 10 and 14 bar.

• At the end, on the base of the maximum output, you obtain the combustion head adjustment from the diagram D.

The adjustment should be made by turning the screws A till the

set-point (see diagram) is on the line with the washer B.

Nozzles delivery

Pump pressure

Combustion head adjustment

Maximum output

Combustion head adjustment

(set-point)

Set-point 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Quemador de Riello

Riello

Riello RLS Series Guía de inicio rápido

Riello

Riello BS3DF Guía de inicio rápido

Riello

Riello RLS 68/E MX Guía de inicio rápido

Riello

Riello RLS 300/E MX Guía de inicio rápido

Riello

Riello 908T4 Guía de inicio rápido

Riello

Riello PRESS GV Series Manual de usuario

Riello

Riello RS 300/EV BLU Guía de inicio rápido

Riello

Riello GS10 Guía de inicio rápido

Riello

Riello RLS 190/M MZ Guía de inicio rápido

Riello

Riello 580T Instrucciones de instalación

Riello

Riello 554T40 Guía de inicio rápido

Riello

Riello PRESS 450 T/N Guía de inicio rápido

Riello

Riello RS 64/M MZ Guía de inicio rápido

Riello

Riello Gulliver RG4D Guía de inicio rápido

Riello

Riello Bio RLS 68/M Guía de inicio rápido

Riello

Riello RS 70/M Guía de inicio rápido

Riello

Riello 517T80 Guía de inicio rápido

Riello

Riello RX35 S/PV H Guía de inicio rápido

Riello

Riello RS 28/M Guía de inicio rápido

Riello

Riello 40 FS15 Guía de inicio rápido

Riello

Riello RLS 68/M MX FS1 Guía de inicio rápido

Riello

Riello GAS 8 P/M Guía de inicio rápido

Riello

Riello RLS 300/EV MX Guía de inicio rápido

Riello

Riello RL 28/M Guía de inicio rápido

Manuales populares de Quemador de otras marcas

True Induction

True Induction TI4B Manual de usuario

Weishaupt

Weishaupt WG20 Series Manual de usuario

Carolina Cooker

Carolina Cooker M116672 Manual de usuario

Unigas

Unigas HTP2000 Manual de usuario

baltur

baltur BT 250 DSG 4T Manual de usuario

muenkel design

muenkel design round burner Manual de usuario

Ecoflam

Ecoflam Multicalor 170.1 Manual de usuario

baltur

baltur BT 14 DSGW Manual de usuario

artisan

artisan Art-SB1 Guía

AESYS

AESYS TurboFire II Manual de usuario

IKEA

IKEA GRILLSKÄR Manual de usuario

RUSTA

RUSTA SAREK Manual de usuario

PROPOINT

PROPOINT 8933657 Manual de usuario

baltur

baltur TBL 1000 ME Manual de referencia

Riello Burners

Riello Burners P 200 P/G Guía de inicio rápido

WLD-TEC

WLD-TEC powerjet Manual de usuario

MSR

MSR DRAGONFLY Manual de usuario

baltur

baltur COMIST 23SP Manual de usuario