Riello 517T80 Guía de inicio rápido

Installation, use and maintenance instructions

2915861 (4) - 07/2015

Forced draught gas burner

One stage operation

CODE MODEL TYPE

3751782 GAS 5 517T80

Declaration of conformity in accordance with ISO / IEC 17050-1

Manufacturer: RIELLO S.p.A.

Address: Via Pilade Riello, 7

37045 Legnago (VR)

Product: Forced draught gas burner

Model: GAS 5

These products are in compliance with the following Technical Standards:

EN 676

EN 12100

and according to the European Directives:

MD 2006/42/EC Machine Directive

LVD 2006/95/EC Low Voltage Directive

EMC 2004/108/EC Electromagnetic Compatibility

The quality is guaranteed by a quality and management system certified in accordance with UNI EN ISO 9001.

Legnago, 21.05.2015 Executive General Manager

RIELLO S.p.A. - Burner Department Research & Development Director

RIELLO S.p.A. - Burner Department

Mr. U. Ferretti Mr. F. Comencini

5861

TECHNICAL DATA

BURNER DESCRIPTION

BURNER EQUIPMENT

ACCESSORY

RADIO DISTURBANCE PROTECTION KIT: code 3010386

If the burner is installed in places particularly subject to radio disturbance (emission of signals exceeding

10 V/m) owing to the presence of an INVERTER, or in applications where the length of the thermostat

connections exceeds 20 metres, a protection kit is available as an interface between the control box and

the burner.

Thermal output

320 - 660 kW 275.200 - 567.600 kcal/h

Fuel

Natural gas Pci 8 - 10 kWh/m

= 7000 - 8600 kcal/m

Minimum gas pressure

For maximum output 9.8 mbar are needed measured at the coupling

with nil pressure in the combustion chamber and gas with calorific

value of 8600 kcal/m

Maximum gas pressure 150 mbar

Electrical supply Three phase 380 V + 10% - 10% ~ 60Hz with neutral

Motor 1.9 A / 380 V

Ignition transformer Primary: 1.8A / 220V - Secondary: 1 x 8 kV - 30 mA

Absorbed electrical power 1.1 kW

Quantity Burner accessories

1 Flange

1 Gasket

8 Screws

1 Flange gasket

1 Pipe fitting for gas train

1– Air shutter control

2– Air shutter lock-nut

3– Control box re-set button

4– Fair leads

5– Wiring terminal block

6– Re-set push-button of the

motor overload relay

7– Air pressure switch

8– Gas pressure test-point Fig. 1

2 1

S7513

5861

OVERALL DIMENSIONS

FIXING TO THE BOILER

GAS SUPPLY

Boiler front-plate

drilling

160

165 M10

D1785

Burner

410 645207

365

437

332

165

ø 155

Rp 1

1/2

S7497 S7498

Length available with special blast tube to be separately required.

Separate the combustion head from the

burner body by loosening the screws 1)

and 2) and withdrawing the group A)

from the holding bars 3).

Fix the group B) to the boiler front plate

4) using the gasket 5) provided as

accessory.

2 3 5 4

A B

S7499

1- Gas pipe line 7- Gas shut off valve

2- Cock valve 8- Burner

3- Filter 9- Gas safety shut off valve

4- Pressure stabilizer 10 - Gas leak control device

5- Pressure test-point 11 - Isolator joint

6- Minimal gas pressure switch

7 9 5

4 3

10 2 1

S7514

5861

WORKING RANGE

COMBUSTION CHAMBER PRESSURE - MAXIMUM OUTPUT

(in compliance with DIN 4788)

MINIMUM GAS PRESSURE - OUTPUT

Pressure: detected at the pressure test-point 8) (fig. 1) with nil mbar into the combustion chamber.

Should the combustion chamber be pressurized, the pressure necessary will be that of the

graph plus the pressurization value.

Example: to obtain 550 kW it is necessary a gas pressure of 9 mbar and the combustion head set as

indicated at page 7.

If the combustion chamber is pressurized at 2 mbar, the pressure detected at the test-point

8) is: 9 + 2 = 11 mbar.

If this value is too high, for very low gas pipework pressures, the gas gear 6) (page 7) could

be more open.

Do not decrease the pressure at the coupling under the values shown in the diagram.

Output: the maximum value is obtainable with gas Pci 8600 kcal/m

CORRELATION BETWEEN GAS PRESSURE AND BURNER OUTPUT

kcal/h

mbar

D1790

kcal/h

mbar

D1791

5861

BURNER ELECTRICAL WIRING

(carried out in the factory)

ATTENTION

In the case of phase-phase feed, a bridge must be fitted on the control box terminal board between

terminal 6 and the earth terminal.

CMV Fan motor contactor

F1 Protection against radio interference

K1 Relay

MB Burner terminal strip

MV Fan motor

PA Air pressure switch

RMG Control box

RT Overload

S Suppressor

SO Ionisation probe

TA Ignition transformer

TB Burner earth

20107483

5861

ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK

(to be carried out by the installer)

Notice

-Leads minimal section 1 mm

- The electric wiring carried out by the installer mustbe in compliance with the rules in force in the Country.

FIXING OF THE ELECTRICAL WIRES

All the electrical wires, which are to be connected to the

terminal block 5) (fig. 1) shall pass through the fair leads

4) (fig. 1) as for this scheme.

1- Three phase supply : fair lead Pg 21

2 - Single phase supply :fair lead Pg 13.5

3- Adjustment thermostat : fair lead Pg 13.5

4- Safety thermostat : fair lead Pg 13.5

5- Gas train : fair lead Pg 13.5,

sheath ø 13

6 / 7 / 8 /9 - Pre-sheared holes

Further prospective signals or controls can be connected to the burner wiring terminal board by removing

the metal weldnuts from the pre-sheared holes and inserting a commun fair lead for the passage and the

clamping of the leads.

NOTES

- Do not exchange the neutral wire with the phase (avoid the plug-pin connection).

- Carry out a safe earth connection.

- Check the stop of the burner, by opening the boiler thermostat and the burner lock-out, by disconnecting

the lead from the flame probe.

WARNING

When closing the burner on its slide-bars, pull towards the outside the high voltage cable and the cable of

the flame detection probe, till to little tension.

HRemote lock-out signal

H 1 Remote lock-out signal of

leak

detection control device

IN Burner manual stop switch

MB Burner terminal strip

PG Min. gas pressure switch

TS Safety control device system

TL Limit control device system

VPS Leak detection control device

VR Adjustement valve

VS Gas safety valve

XP7 Plug for leak detection control

device

D2657

F Ampere T6

S mm

S7529

5861

BURNER START-UP CYCLE

Air-purge: loosen the screw placed on the minimal gas pressure switch mounted on the gas train

AIR PRESSURE SWITCH 7) (fig.1)

The air pressure switch setting shall be carried out after having set

all other adjustment of the burner and the air pressure switch shall

be at its lowest set-point.

When the burner is operating, increase the adjustment pressure

by turning - slowly - clockwise the knob till reaching the burner

lock-out.

Thereafter, turn the knob anticlockwise for 1 mbar and repeat the

burner start-up for checking the regularity: if lock-out intervenes

turn the knob anticlockwise for 0.5 mbar.

CAUTION:

do not turn the ionization probe, maintain the drawing position; should it be close to the ignition electrode,

damage may occur to the control box amplifier.

Screw

Plug for pressure measure

Pressure switch

S7506

1 ÷ 10

mbar

Adjustment knob

S7507

0 - 1 mm

2 - 4 mm

Probe position Ignition electrode position

S7508

5861

COMBUSTION HEAD ADJUSTMENT

Two separate adjustments have to be made: air and gas.

These adjustments can be carried out when the burner is still open, during the installation (see page 2 -

Fixing to the boiler).

Air setting

Loosen the two screws 1) and move the internal

part of the combustion head 2) so that its rear edge

3) is coincident with the desired set-point on the

plate 4). Tighten the screws 1).

Gas setting

Loosen the screw 5), move the ring 6) so that the

pointer 7) is coincident with the desired set-point

8). Tighten the screw 5).

Attention:

the set-point number is the same for air and gas

setting and is given by the following diagram.

Example:

the burner is installed on a boiler of 500 kW, assuming an efficiency of 90% the burner output should be

560 kW.

From the diagram it can be seen that the air and gas settings for this rating should be no. 5.

1 3 4 7

S7496

kcal/h kW

Burner output

Set-point number = for air and gas

D1794

5861

COMBUSTION CHECKS

It is advisable to not exceed 10% of CO

(gas with calorific value of 8600 kcal/m

), in order to avoid the

risk that small changes of the adjustments due, for instance, at draught variation, may cause combus-

tion with insufficient air and consequently formation of CO.

For safety reason the value of 0.1% (one thousand p.p.m.) must not be exceeded.

IONIZATION CURRENT

The minimum current necessary for the control box operation is 3 µA.

The burner normally supplies a higher current value, so that no check is needed.

However, if a measurement of the ionization current is required, it is necessary to disconnect the probe

lead and insert a d.c. microamperometer.

MOTOR LOCK-OUT

This is caused by the thermal protector relay, in case of overloading, or by the lacking of the phase.

To clear, pushdown the appropriate knob, after having removed the protective cover

BURNER START-UP

If during operation the flame shuts off, lock-out occurs within 1 sec.

+ -

Lead Probe

S7511

Normal Lock-out because no ignition

Thermostat

Motor

Ignition transf.

Start valve

Adjust. valve

Lock-out

2 s 40 s 10 s 2 s 40 s 3 s max.

D1798

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Quemador de Riello

Riello

Riello RDB2 Guía de instalación

Riello

Riello RX 500 S PV Manual de usuario

Riello

Riello RS 68/E O2 ULX Guía de inicio rápido

Riello

Riello RS 68/EV BLU Guía de inicio rápido

Riello

Riello Gulliver RG3 Manual de usuario

Riello

Riello 40 GS10/M Guía de inicio rápido

Riello

Riello 464T52 Guía de inicio rápido

Riello

Riello RDB 2.2R BG 24 kW Guía de inicio rápido

Riello

Riello G20 Guía de inicio rápido

Riello

Riello RRS 68/E O2 BLU Guía de inicio rápido

Riello

Riello RLAS 1000 EV Guía de inicio rápido

Riello

Riello RDB2.2 54 BF MISTRAL Guía de inicio rápido

Riello

Riello RDB1R GRANT MILTON 20 kW Guía de inicio rápido

Riello

Riello 40 F20 Guía de inicio rápido

Riello

Riello Gulliver BS3/M TXL Guía de inicio rápido

Riello

Riello GAS 4/2 Hoja de especificaciones

Riello

Riello RG2F Guía de inicio rápido

Riello

Riello 3726312 Guía de inicio rápido

Riello

Riello F5 Guía de inicio rápido

Riello

Riello DB 4 LSM C13 Guía de inicio rápido

Riello

Riello 629 T80 Manual de lista de piezas

Riello

Riello COH 280 Guía de inicio rápido

Riello

Riello PRESS 45 N/ECO Guía de inicio rápido

Riello

Riello 40 G20D Guía de inicio rápido

Manuales populares de Quemador de otras marcas

True Induction

True Induction TI4B Manual de usuario

Weishaupt

Weishaupt WG20 Series Manual de usuario

Carolina Cooker

Carolina Cooker M116672 Manual de usuario

Unigas

Unigas HTP2000 Manual de usuario

baltur

baltur BT 250 DSG 4T Manual de usuario

muenkel design

muenkel design round burner Manual de usuario

Ecoflam

Ecoflam Multicalor 170.1 Manual de usuario

baltur

baltur BT 14 DSGW Manual de usuario

artisan

artisan Art-SB1 Guía

AESYS

AESYS TurboFire II Manual de usuario

IKEA

IKEA GRILLSKÄR Manual de usuario

RUSTA

RUSTA SAREK Manual de usuario

PROPOINT

PROPOINT 8933657 Manual de usuario

baltur

baltur TBL 1000 ME Manual de referencia

Riello Burners

Riello Burners P 200 P/G Guía de inicio rápido

WLD-TEC

WLD-TEC powerjet Manual de usuario

MSR

MSR DRAGONFLY Manual de usuario

baltur

baltur COMIST 23SP Manual de usuario