Ricoh FT5233 Manual de usuario

FT5233/5433/5733

SERVICE MANUAL

IMPORTANT SAFETY NOTICES

PREVENTION OF PHYSICAL INJURY

1. Before disassembling or assembling parts of the copier and peripherals,

make sure that the copier power cord is unplugged.

2. The wall outlet should be near the copier and easily accessible.

3. Note that some components of the copier and the paper tray unit are

supplied with electrical voltage even if the main switch is turned off.

4. If any adjustment or operation check has to be made with exterior covers

off or open while the main switch is turned on, keep hands away from

electrified or mechanically driven components.

5. If the hot roller temperature is low when the main switch is turned on, the

copier starts idling automatically when the warm-up period is completed.

Keep hands away from the mechanical and the electrical components to

avoid any injury.

6. If the start key is pressed before the copier completes the warm-up period

(Ready indicator starts blinking), keep hands away from the mechanical

and the electrical components as the copier starts making copies as soon

as the warm-up period is completed.

7. The inside and the metal parts of the fusing unit become extremely hot

while the copier is operating. Be careful to avoid touching those

components with your bare hands.

HEALTH SAFETY CONDITIONS

1. Never operate the copier without the ozone filters installed.

2. Always replace the ozone filters with the specified ones at the specified

intervals.

3. Toner and developer are non-toxic, but if you get either of them in your

eyes by accident, it may cause temporary eye discomfort. Try to remove

with eye drops or flush with water as first aid. If unsuccessful, get medical

attention.

OBSERVANCE OF ELECTRICAL SAFETY STANDARDS

1. The copier and its peripherals must be installed and maintained by a

customer service representative who has completed the training course

on those models.

2. The RAM board on the main control board has a lithium battery which can

explode if replaced incorrectly. Replace the battery only with an identical

one. The manufacturer recommends replacing the entire RAM board. Do

not recharge or burn this battery. Used batteries must be handled in

accordance with local regulations.

SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL

1. Do not incinerate the toner cartridge or the used toner. Toner dust may

ignite suddenly when exposed to open flame.

2. Dispose of used toner, developer, and organic photoconductor according

to local regulations. (These are non-toxic supplies.)

3. Dispose of replaced parts in accordance with local regulations.

4. When keeping used lithium batteries in order to dispose of them later, do

not put more than 100 batteries per sealed box. Storing larger numbers or

not sealing them apart may lead to chemical reactions and heat build-up.

SECTION 1

OVERALL MACHINE

INFORMATION

1. SPECIFICATIONS

Configuration: Desktop

Copy Process: Dry electrostatic transfer system

Originals: Sheet/Book

Original Size: MaximumA3/11" x 17"

Copy Paper Size: MaximumA3/11" x 17"

Minimum B5/11" x 81/2" - Paper tray

A6/51/2" x 81/2" (lengthwise)

-By-pass feed table

(LCT B5/A4/11" x 81/2" sideways only)

(Duplex Copying)

Multiple:

Single/Overlay: A4 and B5/81/2" x 11" (sideways)

Maximum A3/11" x 17"

Minimum B5/8" x 13"

Copy Paper Weight: •250-sheet paper tray and 1000-sheet large

capacity tray:

52 –128g/m2, 14 –34lb

•By-pass feed table:

52 –157g/m2, 14 –43lb

•Duplex and overlay:

64 –105 g/m2, 17 –28lb

Reproduction Ratios: 4 Enlargement and 6 Reduction

A4/A3 Version LT/LDG Version

Enlargement

200%

141%

122%

115%

200%

155%

129%

121%

Full Size 100% 100%

Reduction

93%

82%

75%

71%

65%

50%

93%

85%

77%

74%

65%

50%

Receiving Tray

Capacity: 250 sheets (B4/81/2" x 14" and smaller)

100 sheets (A3/11" x 17")

Overall

Information

12 February 1992 SPECIFICATIONS

1-1

Power Source: 115V, 60HZ, more than 12A (for N.A)

110V, 60HZ, (for Taiwan)

220/230/240V, 50HZ/60HZ, more than 7A

(for EU and AA)

Power Consumption: Maximum: 1.5 KW

Warm-up: 0.77 KW

Stand-by: 0.14 KW

Copy Cycle (average): 1.2 KW

Noise Emission: Stand-by: less than 40 dB

Copy Cycle (average):

less than 57 dB (copier only)

less than 59 dB (full system)

Maximum:

less than 62 dB (copier only)

less than 63 dB (full system)

Dimensions: Width Depth Height

Type 1 697 mm (1035 mm)

27.4" (40.7") 600 mm

23.6" 542 mm (574 mm)

21.3" (22.6")

Type 2 871 mm (1075 mm)

34.3" (42.2") 600 mm

23.6" 542 mm (574 mm)

21.3" (22.6")

Type 3 871 mm (1075 mm)

34.3" (42.2") 600 mm

23.6" 542 mm (574 mm)

21.3" (22.6")

( ): When the by-pass feed table is opened, the copy tray is extended, and

the platen cover is installed.

Weight: Copier only (Without the optional platen

cover=Approximately 2 kg)

Type 1: approximately 78 kg (172.0 lb)

Type 2: approximately 88 kg (194.0 lb)

Type 3: approximately 84 kg (185.2 lb)

Zoom: From 50% to 200% in 1% steps

Copying Speed: 33 copies/minute (A4/81/2" x 11" sideways)

19 copies/minute (A3)

18 copies/minute (11" x 17")

Warm-up Time: Less than 110 seconds (20°C)

SPECIFICATIONS 12 February 1992

1-2

First Copy Time: Black copy:

4.5 seconds (A4/81/2" x 11" sideways)

Type 1, 3: (Upper tray feed)

4.9 seconds

Type 2: (Large capacity tray feed)

Color copy:

6.6 seconds

Type 1, 3: (Upper tray feed)

7.0 seconds

Type 2: (Large capacity tray feed)

Copy Number Input: Ten keys, 1 to 999 (count up or count down)

manual Image Density

Selection: 7 steps

Automatic Reset: 1 minute standard setting; can also be set to 3

minutes or no auto reset.

Copy Paper Capacity: •By-pass feed table; approximately 20 sheets

•Paper tray: approximately 250 sheets

•Large capacity tray; approximately 1000 sheets

Toner Replenishment: Black: cartridge exchange

(320 g/cartridge)

Color: manual exchange (red, blue, & green

60 g/cartridge)

Optional Equipment: •Platen cover

•Document feeder

•Paper tray unit with one paper tray

•Paper tray unit with three paper trays

•10 bin micro sorter

•20 bin mini sorter

•20 bin midi sorter

•20 bin sorter stapler

•Sorter adapter (needed when installing the

mini or midi sorter, or the sorter stapler)

•Interface PCB (needed when installing the

sorter stapler or the menu reader)

•Editor (only for A074)

•Editing interface adapter (needed when

installing the editor)

Overall

Information

12 February 1992 SPECIFICATIONS

1-3

•Color development unit

•Key counter

•Menu reader (except for Europe)

•A3 counter (service part)

SPECIFICATIONS 12 February 1992

1-4

2. MACHINE CONFIGURATION

2.1 COPIER

TYPE 1 (A069) TYPE 2 (A074) TYPE 3 (A073)

UPPER TRAY 250 DUPLEX 250

LOWER TRAY 250 250 250

LCT – 1,000 1,000

2.2 OPTIONAL EQUIPMENT EDITOR (A916)

ARDF (A497)

MENU READER (A952)

20BIN SORTER

(A411)

20BIN SORTER

(A423)

SORTER STAPLER

(A366)

SORTER ADAPTER

(A328)

10BIN SORTER (A327)

PAPER TRAY UNIT PAPER TRAY UNIT

(A325) (A326)

Overall

Information

12 February 1992 MACHINE CONFIGURATION

1-5

COPIER REQUIRED OPTIONAL

EQUIPMENT

PAPER

TRAY UNIT

1 TRAY

(A325) TYPE 1

(A069) TYPE 2

(A074) TYPE3

(A073)

SORTER

ADAPTER

(A328)

INTERFACE

PCB

(A344)

EDITING

INTERFACE

ADAPTER

(A345)

3 TRAY

(A326) ooo

SORTER

10 BIN

(A327) ooo

20 BIN MINI

(A423) ooo *

20 BIN MIDI

(A411) ooo *

20 BIN

STAPLER

(A366) ooo * **

DOCUMENT

FEEDER ARDF

(A497) ooo

EDITOR (A916) x o x * **

MENU READER (A952) o o o **

COLOR DEVELOPMENT

UNIT (A337) ooo

NOTE1: * The sorter adapter is required to install the 20 bin

mini sorter, 20 bin midi sorter or sorter stapler.

* * The I/F board is required to install the sorter stapler

or Menu Reader.

** * (1) The editing interface adapter is required to install

the editor.

(2) The editing interface adapter can be installed

independently when more precise erasing is

desired.

NOTE 2: When installing the sorter stapler, the copier must be placed

on the paper tray unit or a table of exactly the same height.

MACHINE CONFIGURATION 12 February 1992

1-6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de fax de Ricoh

Ricoh

Ricoh 3800C Series Manual de usuario

Ricoh

Ricoh fax2000l Manual de usuario

Ricoh

Ricoh B383 Manual de usuario

Ricoh

Ricoh FAX2900L Manual de usuario

Ricoh

Ricoh Fx880 Manual de usuario

Ricoh

Ricoh 3800C Series Manual de usuario

Ricoh

Ricoh FAX1130L Manual de usuario

Ricoh

Ricoh FAX3700l Manual de usuario

Ricoh

Ricoh FAX1400L Manual de usuario

Ricoh

Ricoh Fax 680 MP Manual de usuario

Ricoh

Ricoh FAX4500L Manual de usuario

Ricoh

Ricoh FAX3800L Manual de usuario

Ricoh

Ricoh FAX4800L Manual de usuario

Ricoh

Ricoh SMFC210M SecureFax Manual de usuario

Ricoh

Ricoh F102 Manual de usuario

Ricoh

Ricoh FAX7000L Guía de inicio rápido

Ricoh

Ricoh FAX 3320L Manual de usuario

Ricoh

Ricoh MV310E Manual de usuario

Ricoh

Ricoh D3D9 Guía de inicio rápido

Ricoh

Ricoh FAX1180L Manual de usuario

Ricoh

Ricoh FAX 2900Li Manual de usuario

Ricoh

Ricoh FAX 1190L Manual de usuario

Ricoh

Ricoh FAX550 Manual de usuario

Ricoh

Ricoh 3245 Manual de usuario

Manuales populares de Máquina de fax de otras marcas

Samsung

Samsung SF-515 Manual de usuario

Radio Shack

Radio Shack TFX-1031 Manual de usuario

imagistics

imagistics 2030 Manual

Panasonic

Panasonic KX-FL501C Manual de usuario

Panasonic

Panasonic KX-FP200L Manual de usuario

Furuno

Furuno FAX-30 Manual de usuario

Savin

Savin 3740 Manual

Sharp

Sharp FO-51 Manual de usuario

Muratec

Muratec MFX-C3035 Manual de usuario

Panasonic

Panasonic KX-PD505DL Manual de usuario

Panasonic

Panasonic KX-FC265CX-S Manual de usuario

Canon

Canon FAX-L400 Manual de usuario

Sharp

Sharp FO-3150 Manual de usuario

Kyocera

Kyocera KM-F1060 Manual de usuario

Sharp

Sharp FO-2970M Manual de usuario

Panasonic

Panasonic KX-F850 Manual de usuario

Panasonic

Panasonic KX-FLM652CX Manual de usuario

Panasonic

Panasonic KX-F1000BX Manual de usuario