Ricoh gr digital III Manual de usuario
1
Firmware Update Instruction Manual
This manual explains the procedures for downloading the GR DIGITAL III firmware from the
Ricoh website and updating the camera’s firmware.
Perform the following operations to update the firmware.
1. Check the current version of the firmware
Caution
Before updating, be sure to check the firmware version through the following method. If the installed firmware is the latest
version, there is no need to update.
1. Make sure that the camera’s power is turned
off.
2. While pressing the N(Macro) button (1),
hold down the 6(Playback) button (2) for 2-
3 seconds.
• The firmware version will be displayed on the picture
display for about 20 seconds.
3. Check the firmware version displayed on the
picture display.
• e.g. When the current version of the firmware is V1.00,
the version will be shown as [MAIN : V 1.00] as follows:
MAIN : V 1.00
BKUP: V X.XX
MONI : V X.XX
ADJD : V X.XX
EXTD : V X.XX
CPU1 : V X.XX
SH : XXXXXX
ST : XXXXXX
6(2)
N(1)
2
2. Extract the firmware
1. Download the firmware from the Ricoh website.
2. Double-click, or right-click and select [Open] on the downloaded file.
• A dialog screen appears.
3. Click [OK].
• The folder [GR DIGITAL 3 Update] is created, and the firmware is extracted to the folder
[Firmware relX.XX (where X.XX is the version number)]. Check that [glaunch3] (firmware
file) and [glaunch8] (adjusted value file) are inside the folder [Firmware relX.XX].
3. Copy the firmware to an SD memory card
There are two ways to copy the firmware into an SD memory card.
• With an SD memory card loaded in the camera, connect the camera and computer with the
provided USB cable, and copy the firmware to the SD memory card
• Using a card reader or a card writer, copy the firmware to an SD memory card (a card reader
or card writer is required)
To copy the firmware by connecting the camera and computer with the USB
cable
1. If DC Software is installed on your Windows PC, check that DL-10 is not
active.
2. If DL-10 is active, right-click on the DL-10 icon in the task bar, and click
[Exit].
• If the DL-10 icon is not displayed in the task bar, you do not need to perform Step 2.
3. Load a battery with adequate remaining power into the camera.
4. Load the SD memory card into the camera, and turn the power on.
5. Display the camera’s setup menu tab, select [Format [Card]], and press
the $button.
glaunch3
glaunch8
glaunch3
glaunch8
For Windows For Macintosh
3
6. Select [Yes], and press the MENU/OK button.
• The SD memory card is formatted.
Caution
If you format a card that still has images stored on it, the images will be lost. Save the images you do not want to erase in
your computer before formatting the card.
7. Turn the camera off, and connect the camera and computer with the
provided USB cable.
• The camera turns on automatically. If the camera does not turn on automatically, press the
POWER button and turn the power on.
• If DC Software is installed in your Windows PC, DL-10 may automatically start up. In this
case, exit DL-10.
• Click [Cancel] if the [Removable Disk] dialog appears in Windows XP or Windows Vista.
• If iPhoto starts up in Mac OS X, exit iPhoto.
8. Copy the files [glaunch3] and [glaunch8], created when the firmware was
extracted, into [RICOHDCX] root directory. The [RICOHDCX] will be
mounted as follows. For Windows, in [My computer]; for Macintosh, on
the desktop.
• The camera’s drive name may differ depending on the OS you are running.
e.g. [Removable Disk], etc.
9. Confirm that the files have been copied.
10.
For Windows
When the copying of the firmware is completed, double-click the [Safely
Remove Hardware] icon in the task bar.
For Macintosh
Drag and drop the [RICOHDCX] icon to the [Trash] icon. Once the icon
has disappeared, proceed to Step 14.
Caution
If you skip the procedures in Step 10, the firmware copy may not be successful.
11.
Select [USB Mass Storage Device], and click [Stop].
12.
Click [OK].
glaunch3
glaunch8
glaunch3
glaunch8
RICOHDCX
For Windows For Macintosh
4
13.
Click the [Close] button.
14.
Turn the camera off, and disconnect the USB cable.
To copy the firmware using a card reader or a card writer to an SD memory
card
1. Load the SD memory card into the camera, and turn the power on.
2. Display the camera’s setup menu tab, select [Format [Card]], and press
the $button.
3. Select [Yes], and press the MENU/OK button.
• The SD memory card is formatted.
Caution
If you format a card that still has images stored on it, the images will be lost. Save the images you do not want to erase in
your computer before formatting the card.
4. Turn the camera off, and remove the SD memory card.
5. Copy the files [glaunch3] and [glaunch8], created when the firmware was
extracted, into the root directory of the SD memory card.
6. Load the camera with the SD memory card which the firmware was copied
to.
5
4. Update the firmware
1. Make sure that the camera’s power is turned
off.
2. While pressing the !button (1), hold down
the 6(Playback) button (2) for 2-3 seconds.
• A confirmation message for the firmware update is
displayed on the picture display.
3. Press the $button to select [Yes], and press
the MENU/OK button.
• The firmware update starts, and the following message
is displayed on the picture display.
[Checking rewrite file]
[Rewriting program]
4. The camera automatically turns off and restarts.
•If the message [Incorrect rewriting file] is displayed and the camera is automatically turned off, check the camera model
again and retry the update using the correct firmware.
•The firmware files copied to the SD memory card are deleted when you format the SD memory card. Delete them if
necessary.
!(1)
6(2)
Otros manuales para gr digital III
3
Tabla de contenidos
Otros manuales de Cámara digital de Ricoh
Ricoh
Ricoh Caplio RR-1 Manual de instalación
Ricoh
Ricoh Caplio R1V Manual de usuario
Ricoh
Ricoh Caplio G3 Manual de usuario
Ricoh
Ricoh THETA Manual de usuario
Ricoh
Ricoh Pentax K-70 Manual de usuario
Ricoh
Ricoh Caplio 500SE Manual de usuario
Ricoh
Ricoh R02010 Manual de usuario
Ricoh
Ricoh 126C-FLEX TLS Manual de usuario
Ricoh
Ricoh WG-30W Manual de usuario
Ricoh
Ricoh CX6 Manual de usuario
Ricoh
Ricoh Pentax K-3 II Manual de usuario
Ricoh
Ricoh R10 Manual de programación
Ricoh
Ricoh GR10 Manual de usuario
Ricoh
Ricoh Caplio GX100 Manual de usuario
Ricoh
Ricoh PENTAX K-1 II Manual de usuario
Ricoh
Ricoh GR DIGITAL M Manual de usuario
Ricoh
Ricoh PENTAX KF Manual de usuario
Ricoh
Ricoh Caplio R1 Manual de usuario
Ricoh
Ricoh WG-M2 Manual de usuario
Ricoh
Ricoh Caplio 400G wide F Manual de usuario
