Ricoh G565 Manual de usuario

Important

❒

Check the printer nameplate to confirm the model code.

❒

Install the paper feed unit before installing the 2 tray finisher.

❒

Install the memory unit options before attaching the 2 tray finisher.

❒

You cannot install the 2 tray finisher unless both the paper feed unit and duplex unit with options are installed.

❒

The 2 tray finisher requires the optional printer hard disk or optional memory unit of total 128 MB.

❒

You cannot install the 4-bin mailbox and 2 tray finisher at the same time.

Note

❒

The 2 tray finisher weighs approximately 53kg (116.9 lbs).

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Caution

•

Before installing options, the machine should be turned off and unplugged for at

least thirty minutes.Components inside the machine become very hot, and could

result in a burn if touched.

•

When lifting the machine, use the grips on both sides. The machine could break

or cause injury if dropped.

•

It is dangerous to handle the plug with wet hands. Doing this may result in receiving

an electric shock.

•

Before moving the machine, unplug the power cord from the outlet. If the cord is

unplugged abruptly, it could become damaged. Damaged plugs or cords can

cause an electrical or fire hazard.

•

When moving the 2 tray finisher, hold the center of both sides, and lift slowly.

Lifting carelessly or dropping it may cause injury.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○

SR770

(Code: G565)

For Machine Code:

G060 / G080/ G082/ G106

INSTALLATION GUIDE

Check the contents of the box:

Description Q’ty

Finisher 1

Short Screws 2

Long Screws 6

Connecting Bracket 1

Mounting Bracket 1

Rail 1

2 Tray Finisher Trays 2

Installation Guide(This sheet) 1

Be sure to check the following points:

•

The power is turned off.

•

The power cord is unplugged from the wall outlet.

•

The interface cable is unplugged from the printer.

Remove the adhesive tape and packing materials.

Note

❒Do not remove the adhesive tape holding the cable yet. Remove

it in step .

Front and Side

Back

G565-8600C

Interior

Slowly open the front cover by pulling on the two areas on

the left and right.

Remove the green screwdriver, and then close the front

cover.

Use this screwdriver for all attachment and detachment of screws.

ZHXH171J

Note

❒After using the screwdriver, return it to its original position on

the inside of the front cover.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Stand the external tray of the printer.

쐃

Stand it vertically.

ZHXH330J

쐇

Fold it over the top of the printer.

ZHXH340J

Insert the rail with a wheel in the mounting bracket.

Temporarily fasten one long screw in the position, as

shown. Turn the screw three to four times by hand.

Insert the rail, assembled in step

into the base area

under the printer.

Hook the hole of the mounting bracket on the screw

temporarily fastened in step

Holding the mounting bracket using both hands, move it

in the direction of up (

햲

) to the right (

햳

With the left corner of the mounting bracket in the

position pointed by the arrow on the printer, fasten the left

side of the mounting bracket using a long screw and the

provided screwdriver. Also tighten the screw on the right

side temporarily fastened in step

Temporarily fasten the two long screws in the positions

shown. Turn the screws three to four times by hand.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Hook the connecting bracket onto the screws temporarily

tightened in step

Fasten the right side of the connecting bracket using a

long screw and the provided screwdriver. Also tighten the

two screws temporarily tightened in step .

Note

❒If you have the 1000-sheet paper feed unit or 2000-sheet Large

Capacity Tray installed, proceed to step .

If you have the 500-sheet paper feed unit installed,

change the position of the connecting bracket on the side

of the 2 tray finisher to the lower level. Remove the two

screws using the provided screwdriver, the move the

connecting bracket down, and then refasten the screws.

Place the printer’s trail on the 2 tray finisher, and then

slide until it stops.

Fasten the rails using a long screw provided screwdriver.

Slowly push the 2 tray finisher toward the printer until it

stops.

ZHXH350J

Remove the tape fastening the cable to the 2 tray

finisher.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Connect the cable of the 2 tray finisher to the lower

connector on the back of the printer.

Place the two 2 tray finisher trays in the 2 tray finisher.

Note

❒The two finisher trays are identical.

쐃

Adjust the notch on the left side of the 2 tray finisher

tray to the cable coming out from the 2 tray finisher.

This step is unnecessary if you are using the lower area.

쐇

With the 2 tray finisher tray laid horizontally, slide it in

at a slant until it stops.

쐋

Fasten the finisher tray using a short screw and the

provided screwdriver.

쐏

Use the same steps (

쐇

and

쐋

) to install the other 2

tray finisher trays.

Be sure to return the provided screwdriver to its original

position on the inside of the front cover.

Put the finisher tray installed on the duplex unit back in

place.

쐃

Lift the top.

ZHXH360J

쐇

Lower slowly.

ZHXH370J

Note

❒After finishing the installation, you can check the finisher is

installed properly: Print the configuration page from the “List/

Test Print” menu. If it is installed properly, you will see “2 Tray

Finisher” appear in the “Options” list. (G060, G080, G106)

❒After finishing the installation, you can check the finisher is

installed properly: Print the configuration page from the "Print

Menu" menu. If it is installed properly, you will see "Finisher:

Installed" appear in the “Installed Options” list. (G082)

❒If the finisher is not installed properly, repeat the procedure

from step . If you cannot install it properly even after

reinstallation, contact your sales or service representative.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora todo en uno de Ricoh

Ricoh

Ricoh Aficio 400 Manual de usuario

Ricoh

Ricoh Pro C900 Manual de lista de piezas

Ricoh

Ricoh Aficio SP 1100SF Manual de usuario

Ricoh

Ricoh MP 171L Manual de usuario

Ricoh

Ricoh Pro C5100 Series Manual de usuario

Ricoh

Ricoh SP 325DNw Manual de usuario

Ricoh

Ricoh Aficio SP C830DN Manual de funcionamiento

Ricoh

Ricoh Pro C900 Manual de usuario

Ricoh

Ricoh Aficio FX200 Manual

Ricoh

Ricoh SP 230 SFNw Manual de usuario

Ricoh

Ricoh Aficio 1515 Manual de usuario

Ricoh

Ricoh Aficio 240W Manual de usuario

Ricoh

Ricoh B022 Manual de usuario

Ricoh

Ricoh PRO 8100 Manual de usuario

Ricoh

Ricoh 2018 Manual de usuario

Ricoh

Ricoh B173 Manual del operador

Ricoh

Ricoh Aficio MP 1350 Manual de servicio

Ricoh

Ricoh Aficio AP3800C Manual de funcionamiento

Ricoh

Ricoh A292 Manual de usuario

Ricoh

Ricoh 8025e Manual de usuario

Ricoh

Ricoh Savin en5100WD Manual de usuario

Ricoh

Ricoh Aficio 615C Manual de usuario

Ricoh

Ricoh S-C3 F Manual de usuario

Ricoh

Ricoh Priport JP5000 Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario

Oce

Oce VarioLink 5022 Manual de usuario