Ricoh Aficio 450 Manual de usuario
SCANNER Option Type
450
OPERATING INSTRUCTIONS
SCANNER REFERENCE(option)
ND0A0101
Read this manual carefully before you use this product and keep it handy for future
reference.
For safety, please follow the instructions in this manual.
SCANNER Option Type 450 OPERATING INSTRUCTIONS
Printed in Japan
UE USA A695-8510
EE GB
Introduction
This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine all operators should carefully read and follow the instructions in
this manual.Please keep this manual in a handy place near the machine.
Please read the Safety Information in the “Copy Reference” before using this machine. It contains im-
portant information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Important
Parts of this manual are subject to change without prior notice. In no event will the company be liable
for direct, indirect, special, incidental, or consequential damages as a result of handling or operating
the machine.
Note to users in the United States of America
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio /TV technician for help.
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Caution
Properly shielded and grounded cables and connectors must be used for connections to host computer
(and/or peripheral) in order to meet FCC emission limits.
Declaration of conformity
Product Name: Scanner Option
Model Number: Type 450
Responsible party: Ricoh Corporation
Address: 5 Dedrick Place, West Caldwell, NJ 07006
Telephone number: 973-882-2000
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received,
including interference that may cause undesired operation.
Note to users in Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Remarque concernant les utilisateurs au Canada
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
In accordance with ISO Standard 7001, this machine uses the following symbols for the main power
switch:
a
aa
ameans POWER ON.
b
bb
bmeans POWER OFF.
Declaration of Conformity
“The Product complies with the requirements of the EMC Directive 89/336/EEC and the Low Voltage
Directive 73/23/EEC.”
i
How to Read this Manual
Symbols
In this manual, the following symbols are used:
Important
If this instruction is not followed, paper might be misfed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparations required before op-
erating.
Note
This symbol indicates precautions for operation, or actions to take after misop-
eration.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[ ]
Keys that appear on the machine's panel display.
Keys and buttons that appear on the computer's display.
{}
Keys built into the machine's operation panel.
ii
TABLE OF CONTENTS
1.Preparation
The Scanner Interface............................................................................... 2
Requirements............................................................................................. 3
Connecting to the Computer.................................................................... 4
Making the connection .................................................................................. 4
Setting the SCSI ID....................................................................................... 4
2.Setting Originals
Setting Originals on the Exposure Glass................................................ 8
Setting Originals In The Document Feeder (ADF)................................ 10
1-sided Scanning ........................................................................................ 11
2-sided Scanning ........................................................................................ 12
3.Appendices
Troubleshooting...................................................................................... 15
Status Messages ..................................................................................... 16
Specification............................................................................................ 18
1
1. Preparation
This chapter provides important information on the requirements for using your
machine installed with the scanner unit. This chapter also provides information
on setting up your machine as a scanner.
Preparation
2
1
The Scanner Interface
The scanner unit is installed in the left side of your machine (as shown in the il-
lustrations) The scanner unit connects to a computer through a 50–pin half –
pitch (pin type) SCSI connector.
1. Scanner unit interface 50–pin half-pitch (pin type) SCSI connector
Optional equipment is installed in this illustration.
1
Requirements
3
1
Requirements
In order to use your machine as a scanner, the following hardware/software is
required in the computer that will be connected to the scanner. Make sure that
all the necessary hardware and software is in place before attempting to scan.
❖
❖❖
❖
CPU
Intel®Pentium 75MHz or better.
❖
❖❖
❖
OS
Windows®95/98/3.11, Windows NT®3.51, or NT®4.0.
❖
❖❖
❖
Memory
16MB or more (for scanning).
48MB recommended.
❖
❖❖
❖
Hard disk
100MB or more of free disk space recommended. Approximately 16MB of
space is required to save one page of an A4 monochrome image scanned at
400dpi with a 256–value gray scale.
❖
❖❖
❖
SCSI board
Use a SCSI board recommended by the local dealer. The system may not op-
erate properly with some SCSI boards.
❖
❖❖
❖
SCSI interface cable
Use a SCSI interface cable recommended by the local dealer. The type of SCSI
interface cable required depends on the SCSI board that is installed in the
computer.
Preparation
4
1
Connecting to the Computer
The scanner unit uses SCSI-2 interface to connect to the computer.
Important
❒Do not daisy chain other SCSI devices with the scanner.
❒The scanner might not operate properly with some SCSI boards (installed in
the computer).
❒Since the scanner unit has a built-in terminator, no terminator needs to be
connected to the scanner. A terminator is only required at the other end of the
connection (i.e.,on the SCSI board in the personal computer).
Making the connection
ATurn the computer off.
BMake sure that none of the other functions are in use, and then turn off the
main power switch of the machine.
CConnect the 50–pin half-pitch (pin type) end of the SCSI interface cable to
the SCSI connector on the machine.
DConnect the other end of the SCSI interface cable to the computer.
Setting the SCSI ID
The SCSI ID for the scanner is initially set to “4”. Normally, there is no need to
change this ID. If it is necessary to change this ID, follow the procedure bellow.
ATurn the computer off.
BTurn on your machine, and wait until ”Ready” appears on the panel dis-
play of the machine.
Tabla de contenidos
Otros manuales de Impresora todo en uno de Ricoh
Ricoh
Ricoh MP C3003 Manual de usuario
Ricoh
Ricoh PRO C7200 Manual de usuario
Ricoh
Ricoh Aficio SP C240SF Manual de usuario
Ricoh
Ricoh K-C3.5L Manual
Ricoh
Ricoh Aficio MP 1600L2 Guía de inicio rápido
Ricoh
Ricoh Pro C900s Instrucciones de instalación y mantenimiento
Ricoh
Ricoh PRIPORT JP730 Manual de usuario
Ricoh
Ricoh Aficio 3224C Manual de usuario
Ricoh
Ricoh SP 150 Guía de inicio rápido
Ricoh
Ricoh Aficio 1515MF Instrucciones de uso
Ricoh
Ricoh FT6655 Manual de usuario
Ricoh
Ricoh A095 Manual de usuario
Ricoh
Ricoh Aficio MP C305 Manual de usuario
Ricoh
Ricoh 2020D - Aficio B/W Laser Instrucciones de uso
Ricoh
Ricoh SP 311SFNw Manual de usuario
Ricoh
Ricoh Aficio SP 1200SF Manual de usuario
Ricoh
Ricoh A172 Manual de usuario
Ricoh
Ricoh SP C260SFNw Manual de usuario
Ricoh
Ricoh Pro C900 Manual de usuario
Ricoh
Ricoh Pro C651EX Manual de usuario
Manuales populares de Impresora todo en uno de otras marcas
Triumph Adler
Triumph Adler DC 2016 Manual
Epson
Epson WorkForce WF-2510 Guía del usuario
Epson
Epson Stylus Scan 2000 Manual de instalación y operación
Epson
Epson PictureMate Snap PM 240 Manual de instrucciones
Konica Minolta
Konica Minolta bizhub C35 Manual de usuario
Brother
Brother MFC-J430w Manual de usuario
