Rice Lake SCT-2200 Manual de usuario

SCT-2200

Quick Setup Guide

Key Functions

Setup Menu

1. Press the ON/OFF key ( ) to turn the instrument on.

2. Press the mode key ( ) when the firmware version displays to enter the setup menu.

3. Press the print key ( ) in the setup menu to view/select the parameter choices.

When settings are complete press until the indicator displays SAVE?. Press to save set up and return to

weigh mode. Pressing any other key exits the setup and discards changes.

Key Function Key Function Key Function

ZERO

In setup: scroll forward through parameters

In numeric input: decreases digit to be modified MODE

In setup: quickly position the first step of a menu

In numeric input: selects digit to be modified, from

left to right ON/OFF

Turn the instrument on/off

In setup: exit a step without confirming the setting

In numeric input: clears the present value

TARE

In setup: scroll back through the functions

In numeric input: increases digit to be modified PRINT

In setup: enter into a parameter or to confirm a

setting

In numeric input: confirms the entry made

canopn

dev.net

mb.tcp

Profin

Eth.Cat

profib

ethip

yes

primar

FUNC

set.Add

baud

yes

hub

OUT.01 NO/NC

485

AN.oUT

AOZER

MODE

AOMAX

INP.02

AOMIN

INP.01

OUT.02

OUTPUT

FLD.BUS

INPUTS

NONE

GROS

NET

DIV.DEC

CEL.CAP

CEL.SEN

DEAD.LD

CAPAC

0.CALIB

ZERo

SPAN

ADC.uV

bus.typ

num.sca

SCA.Add

Press and to set decimals and minimum division.

Press and to set baud rate

Press , and to set the total capacity of the load cells.

Press , and to set number of additional units.

Press , and to set the mV/V sensitivity of the load cell.

Press , and to set the dead load present on the load cell.

Apply calibration weight. Press , and to enter applied calibration weight.

Set the analog output on net or gross weight.

Set the maximum value of analog output.

Set the analog output when scale shows zero weight.

Set the minimum value of analog output.

Set the key to be emulated by the input.

Set the output normal state.

For new acquisition of zero, with scale empty. Establishes new zero reference.

Disabled.

Setpoint on the gross weight.

Setpoint on the net weight.

Optional Analog

Model Parameter

Press , and to set the scale capacity.

Quick calibration of zero.

Check the load cell signal in millivolts.

(If more than one cell, set to average mV/V of the cells)

Default Factory Calibration

The instrument has a default calibration with the

following features:

Capacity = 10,000 kg

Load cell sensitivity = 2.000mV/V

Divisions = 1

Theoretical Calibration

Use parameters div.dec, capac, cel.cap, cel.sen,

dead.ld to perform a theoretical calibration.

Calibration Using Known Weight

Use parameters div.dec, capac, zero, span to

perform a standard calibration with a known weight.

For parameters zero & span, press and wait

for ERNOT, STORE?. Then press to accept.

For parameter span, apply test weight before

pressing .

Setpoint Programming

In the weigh mode, press and hold to access out-

put’s setpoint programming.

Note

PN 184974 Rev B

September 10, 2019

230 W. Coleman St. • Rice Lake, WI 54868 • USA

U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319

Rice Lake Weighing Systems is an ISO 9001 registered company.

www.ricelake.com

PN 184974 Rev B

September 10, 2019

Wiring Diagram

SCT-2200

IN 2

IN 1

OUT 2

OUT1

COM

12/24 VDC

Analog Output

PN 182589 only

RS-232

Load Cell

CAL

Analog Output (PN 182589 only)

Voltage

8 V+ +10 V

9 V- 0 V (GND)

Current

10 I+ +20 mA

11 I- -0 mA (GND)

NOTE:

Max. resistance on output current: 350 Ω

Min. resistance on output voltage: 10 kΩ

Pin Number Label Description

VE 12-24 VDC Power Supply

1 GND 0 VDC (GND)

2 +VDC +12-24 VDC

Inputs and Outputs

Outputs (48 VAC or 60 VDC, 150 mA max)

3 OUT1 Output 1

4 OUT2 Output 2

5 COMOUT Common Output

Optoisolated Inputs Positive Logic

(12-24 VDC, 5-20 mA max)

6 IN1 Input 1

7 IN2 Input 2

Connect input common to

ground

Serial Port

RS-232

12 TX Transmission

13 RX Reception

14 GND Ground

RS-485

RJ45 Plug-IN/OUT 485 Line

Load Cell Connections

15 SIG+ Signal +

16 SIG- Signal -

17 SEN+ Sense +

18 SEN- Sense -

19 EXC+ Excitation +

20 EXC- Excitation -

Pin Number Label Description

Otros manuales para SCT-2200

Otros manuales de Transmisor de Rice Lake

Rice Lake

Rice Lake SCT-2200 Manual de usuario

Rice Lake

Rice Lake SCT-1000ETHERNET Manual de usuario

Rice Lake

Rice Lake MSI TranSend Series Manual de usuario

Rice Lake

Rice Lake SCT-1SX Series Manual de usuario

Rice Lake

Rice Lake SCT-20 Manual de usuario

Rice Lake

Rice Lake SCT-3300 Manual de usuario

Rice Lake

Rice Lake SCT-4X-MODBUS TCP/IP Manual de usuario

Rice Lake

Rice Lake SCT-2200 Manual de usuario

Rice Lake

Rice Lake SCT-4X-AN Manual de usuario

Rice Lake

Rice Lake SCT-1SX Series Manual de usuario

Rice Lake

Rice Lake SCT-1SX-Ethernet/IP Manual de usuario

Rice Lake

Rice Lake SCT-1SX-AN Manual de usuario

Rice Lake

Rice Lake SCT-1SX-PROFINET Manual de usuario

Rice Lake

Rice Lake 30 Series Guía del administrador

Rice Lake

Rice Lake SCT-1SX-MODBUS TCP/IP Manual de usuario

Rice Lake

Rice Lake SCT-1SX Series Manual de usuario

Rice Lake

Rice Lake Advanced Series Manual de usuario

Rice Lake

Rice Lake SCT20-DN Manual de usuario

Rice Lake

Rice Lake SCT-1100 Manual de usuario

Rice Lake

Rice Lake 20 series Manual de usuario

Rice Lake

Rice Lake SCT-10 Series Guía del administrador

Rice Lake

Rice Lake SCT-4X Series Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario