RF SOLUTIONS PRO Series Manual de usuario

PRO

Professional Radio Control Series

204

205

•

Ready to Use Remote Control

•

4, 8/16 Channel Systems

•

Range:

Up to 200 metres at 433MHz

Up to 1,000 metres at 433MHz NB

•

Relay Outputs: Momentary, Latching, Timed

•

Receiver IP65

Applications

•

Lighting Control

•

General Purpose Remote Switching

•

Door Control

•

Industrial remote Switching

•

Access Control

Available as 4 - 16 channels the Professional range are ready to operate general purpose remote

control systems using a highly secure transmission protocol for reliable operation.

The receiver unit is rated IP65 with integral power supply containing industrial standard ‘DIN Rail’

‘receiver’ and ‘relay output’ modules (interchangeable). Other modules with higher switching

capability are available.

The relay outputs may be user set to operate as latching or momentary. Output 1 may be set to

timed from 1-15 minutes.

Additional transmitters can be added using the easy learn procedure. Any transmitter switch can

be mapped to any individual or combination of receiver output(s).

PRO

Professional Radio Control Series

Part Number Description Range**

(Metres)

Freq

(MHz)

Relay Outputs

(each @230Vac)

204PRO4-433F 4 channel Remote Control System 100 433.92 4 x 12A

204PRO16-433F 16 channel Remote Control System 100 433.92 16 x 12A

205PRO4-433F 4 channel Remote Control System 200 433.92 4 x 12A

205PRO8-525N 8 channel Remote Control System 1,000 434.525 8 x 12A

** Range stated is optimum, direct line of sight. In worst conditions this can be reduced by up to 50%

Custom systems

We regularly supply pre-wired / bespoke systems, please contact our sales dept for further assistance

Receiver Unit

The receiver consists of interchangeable modules which are connected via ribbon cables. (as shown below)

Antenna

The Antenna is held internally, this is to save drilling the enclosure on the top. This may have some effect to

the range for specific applications which may require the antenna externally mounted. At all times please

ensure that antenna is pointing in a vertical direction and away from high interference sources.

R. F. Solutions Ltd.,

Unit 21, Cliffe Industrial Estate, South Street, Lewes,

E. Sussex, BN8 6JL, England

Tel +44 (0)1273 898 000 Fax +44 (0)1273 480 661

Email [email protected] http://www.rfsolutions.co.uk

RF Solutions is a member of the Low Power Radio Association

Information contained in this document is believed to be accurate, however no representation or warranty is given and R.F. Solutions Ltd. assumes no liability with respect to the accuracy of such information.

Use of R.F.Solutions as critical components in life support systems is not authorised except with express written approval from R.F.Solutions Ltd.

PRO

Professional Radio Control Series

Pre-Configuring the Remote Control System

There are three Steps:

1. Pre-Configure the 210Rx to operate with a type of Transmitter (e.g. the 204 range or 205 range)

2. Map the Transmitter(s) switch(es) to the 210Rx output(s)

3. Set the 210Rx outputs to be latching, momentary or timed.

1.1 Pre-Configure the 210Rx to operate with a Transmitter Series

1. Ensure option link J8 is open.

2. Apply power to the 210Rx, All output LEDS flash alternately. This is factory reset default state.

3. Briefly Press any switch on the transmitter.

The 210Rx will now confirm this by flashing LED 1 to show it is configured for use with a handheld

transmitter.

Note This will now happen at each power on.

PRO

Professional Radio Control Series

Mapping a Transmitter Switch to a 210 Receiver Output

One or many transmitter switches may be mapped to one or many 210Rx outputs, Decide which switch on the

Transmitter is to operate which output channel on the 210 Receiver decoder.

1. Briefly press the 210 Rx learn switch until the LED1-16 indicates the desired output channel

2. Operate the desired transmitter switch briefly

3. The LED on the 210Rx will extinguish.

4. Operate the desired transmitter switch briefly again

5. The LED on the 210Rx will turn on briefly and then extinguish.

6. The selected transmitter switch will operate the 210Rx output channel.

This procedure may be repeated for each transmitter and each 210Rx output required.

1.2 Configuration of the 210Rx Receiver Decoder Outputs

Option links LK 1-16 configure the operation of the outputs. Please note that the link status is read only on

‘power up’ and thus after changing the links, power must be removed and re-applied.

LK 1–16 Output 1 Outputs 2 -16

Open Mom or Timed Mom (The O/P operates for as long as the transmitter switch is held on)

Connected Latch or Timed Latch (The O/P changes state each time the Transmitter is operated)

1.2.1 Setting the Timed output (Channel 1)

This is set by VR1 with a delay of from 0 to 15 minutes. To set the time delay:

1. Remove power.

2. Place a shorting link header on option link J8.

3. Apply power

4. Depress and release the learn button twice.

5. The 210Rx will then enter the ‘time set mode’

6. LED1 will illuminate, indicating that output 1 time delay is to be set.

7. Using a fine screwdriver, adjust potentiometer VR1.

8. An indication of the time delay set is shown by LED’s 9-15.

After setting the timed output the unit must be powered down and option link header J8 removed before

it can be used.

1.3 Erasing the 210Rx Receiver Outputs (Return to Factory Default State)

1. To completely erase the 210Rx decoder’s memory, press and hold the 210Rx learn switch.

2. The learn LED (LED 17) will illuminate

3. Hold the Learn switch until the learn LED extinguishes (approx 10 seconds).

4. Release the learn button and all the output LED’s 1-16 will now flash alternately to indicate that all encoder

data has been erased and the 210Rx has returned to factory default state.

Note: It is not possible erase individual transmitters.

PRO

Professional Radio Control Series

COM

Relay Connections when

Transmitter NOT Operating

COM

Relay Connections when

Transmitter OPERATING

1.4 Connecting output Modules to the 210 Receiver

The receiver has 16 outputs. These are connected to the relay output module via a ribbon cable.

The outputs are presented according to the following table.

1.5 Relay Outputs

Each output relay provides an isolated switch. Connections are Common (COM), Normally Open (NO),

Normally Closed (NC).

Antenna and Range

2.1 Antenna

The system includes an antenna, It is situated within the enclosure (to save penetrating the enclosure)

If the range is inadequate then it may be necessary to mount the antenna protruding from the enclosure. This

may be easily fitted using the provided panel mount BNC socket. The antenna cable may be extended however

please note that typically there is a 50% range reduction with every 3metres of coax cable used!

For increasing range performance a +3dB gain antenna is available. This is supplied with wall mounting bracket

and 2metres of coax cable, it plugs in directly to the BNC connector.

2.2 Range

The antenna choice and position directly controls the system range. Keep it clear of other metal in the system.

The best position is protruding from the top of the product. This is often not desirable for practical or ergonomic

reasons and thus a compromise may be needed. If an internal antenna must be used then try to keep it away

from other metal items, and in particular large ones like transformers, batteries and PCB tracks and earth

planes.

Note that the space around the antenna is as important as the antenna itself. All radio systems are dependant

on a radio signal being received through airspace.

The range quoted is the optimal in direct line of sight without obstacles and in good atmospheric conditions.

2.3 Signal integrity

In systems where many encoders are in close proximity there may be occasions when, due to signal overlay

between encoders, it is difficult or impossible to guarantee system integrity. In such circumstances it is the

responsibility of the installer to ensure that the system performance is adequate for the purposes of the

installation.

210 receiver

Connector

O/P Channels

1 1 - 4

2 5 – 8

3 9 – 12

4 13 – 16

PRO

Professional Radio Control Series

Technical Specifications

Transmitters

204 Series

Dimensions 96 x 47 x 23mm

Battery 2 x CR2016 Lithium Cell

205 Series

Dimensions 4 Switch unit 105 x 58 x 18 (not including ANT)

8 / 16 Switch unit 250 x 90 x 41 (not including ANT)

Battery 4 Switch unit 2x AAA

8 / 16 Switch unit 2 x CR2016 Lithium Cell

Receiver Unit

Dimensions 315 x 235 x 130mm

Insulation class II

Sealed hinged lid screws

DIN Rails mounted on steel plate

Integrated 12Vdc moulded Power Supply

5 Amp Fused terminal block

Material GW PLAST 120 °C

A 12Vdc power supply is incorporated. 12Vdc is presented on a fused terminal block. A Gland is

supplied to enable power to enter the enclosure.

Learning Capacity: The receiver has the capacity to learn upto 50 units

(Where 1 unit is defined as a button on a transmitter)

Dimensions

External 315 x 235 x 130mm

Internal 300 x 220 x 120mm

DIN Rail length 1 285mm

DIN Rail length 2 180mm

Technical Specifications

Input Voltage 110-240Vac

Output Voltage 12Vdc +/-5%

Output Current 1A

Output Polarity: White Dashed Wire =+12V

Storage Temperature: -10 to +70

Celsius.

Operating Temperature: 0 to +55

Celsius.

Electrical Characteristics Min Typical Max Units

Supply Voltage: 12V Supply 10 12 16 V

Supply Voltage: 24V Supply 21 24 30 V

Supply Current : Quiescent 25 mA

Time from Tx Switch depressed to 210Rx output 100 mS

Time from Tx Switch release to Decoder output 200 mS

Switched output Voltage (I out = 1mA)

Logic Low

Logic High

3.5

0.2

3.8

0.8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de RF SOLUTIONS

RF SOLUTIONS

RF SOLUTIONS MAINSLINK–PRO Manual de usuario

RF SOLUTIONS

RF SOLUTIONS PRO Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS HORNETPRO-8S1 Manual de usuario

RF SOLUTIONS

RF SOLUTIONS TRAP-SHUFFLE Game Simulator Manual de usuario

RF SOLUTIONS

RF SOLUTIONS PRO TRAP Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS QUANTAFOB Manual de usuario

RF SOLUTIONS

RF SOLUTIONS FOBOEM-4S4 Manual de usuario

RF SOLUTIONS

RF SOLUTIONS ELITE-L Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS TRAP Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS ELITE-KIT Manual de usuario

RF SOLUTIONS

RF SOLUTIONS Hornet-S1 Manual de usuario

RF SOLUTIONS

RF SOLUTIONS TRAP Manual de usuario

RF SOLUTIONS

RF SOLUTIONS EZTEXT-DIN Manual de usuario

RF SOLUTIONS

RF SOLUTIONS HORNETPRO MAINS Manual de usuario

RF SOLUTIONS

RF SOLUTIONS RIoT-Minihub Manual de usuario

RF SOLUTIONS

RF SOLUTIONS TRAP Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS FOBBER-8T6 Manual de usuario

RF SOLUTIONS

RF SOLUTIONS EZTEXT Manual de usuario

RF SOLUTIONS

RF SOLUTIONS ELITE Manual de usuario

RF SOLUTIONS

RF SOLUTIONS QUANTAFOB Manual de usuario

RF SOLUTIONS

RF SOLUTIONS TAURUSDIN Manual de usuario

RF SOLUTIONS

RF SOLUTIONS ELITE Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS ELITE Series Manual de usuario

RF SOLUTIONS

RF SOLUTIONS HORNETPRO Series Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación