RF Mogul Eagle Manual de usuario
SATELLITE TV
MANUAL
4 December 2013
The Eagle Manual
2
The Eagle Manual
3
Index
Warning ....................... 4
Mount Definitions ........................ 5
Controller View ....................... 6
Configuration and Software Versions ....................... 8
Menu Options ....................... 9
Connector Wiring Diagram ....................... 10
Raising the ODU Using a 12 VDC Source ....................... 10
vGPS (DirecTV) Block Diagram ....................... 11
Foot Print and Clearances ....................... 12
Operation ....................... 13
LCD Display ....................... 14
Service Messages ....................... 15
Returning Parts to the Factory ....................... 16
The Eagle Manual
4
WARNING
Make all electrical and coax connections from the controller to the mount
and LNB's BEFORE applying power to, or connecting the satellite
receiver to the controller.
Note: When the controller is turned OFF it will still pass voltage from the receiver to the
LNB if the receiver is plugged in to 110 AC. Shorting of the coax at any time during
installation may cause damage to either the Controller or the DiSEqC Switch (if installed).
Failure to follow this procedure can result in voiding of warranty replacement, not to
mention time spent trying to troubleshoot a system that does not perform.
REMEMBER
90% of all problems are a result of CONNECTIVITY or CONFIGURATION.
The Eagle Manual
5
Mount definitions
A system consists of several components
Connector Weather Cover
Mounting Feet
Mount or Azimuth Base
LNB Arm Assembly
Note: Your LNB
may vary from the
one pictured
depending upon your
system configuration.
Reflector/Parabola
MOUNT (ODU)
Items included with the system and
not shown.
1 ea LNB Landing Plate
15' Control Cable, 25'
1 ea Connector, green, 12 pin
1 ea Power Supply, 12 VDC 7 amp
1 ea RE-1000 User Guide
1 ea EAGLE Controller
Clam Shell
The Eagle Manual
6
Controller Views
FRONTAL VIEW Definitions and Usage
FIND
Directs the system to "FIND" Satellites
Navigates through the menu and selects a particular function
STOW
Directs the system to "STOW" the mount and prepare it for travel
Navigates through the menu and selects a particular function
LCD Display
Displays the actions of the system
USB Programming Port
Used for changing software
POWER
Turns controller ON and OFF
Navigates through the Menu options
LEDLNB indicates the receiver coax is attached to the controller
SYSTEM indicates power is being supplied to the controller
CONTROLLER (IDU)
The Eagle Manual
7
REAR VIEWDefinitions and Usage
CONNECTIONS
POWER
12 VDC 7 amp (power supply provided)
CONTROL CABLE CONNECTION:
Termination of the 12 wires of the control cable to the controller takes place here.
TO SATELLITE RECEIVER
This is a coax pass-through connection to your satellite receiver (Satellite IN). It is
optional except for DirecTV SWM.
TO LNB:
This is a coax connection to the Antenna's LNB. The connection is made at the base of the mount to
any one of 4 coax cables that run through the mount and is secured to the LNB.
If you have DirecTV SWM, then the cable attached to the DiSEqC switch must be routed
directly to the controller uninterrupted to the connection marked "TO LNB". (see configuration to
determine which coax at the base of the mount goes to the controller).
Label on the bottom of the controller
CONTROLLER (IDU)
To REC To LNB
The Eagle Manual
8
Configurations and Software Version
Each of the Program Providers will require different software
EAGLE -1 SHAW Direct = 107.3, 107.3, 111.1 Satellites (For Canadian Use Only)
EAGLE -2 DirecTV SWM = 99, 101, 103 or 99,101,103,110 and 119 Satellites
EAGLE -3 Dish Network = 110, 119, 129 Satellites
EAGLE -4 Bell Express = 81, 92 Satellites (For Canadian Use Only)
TO CONFIGURE
Configuration of your system is done through software. There are different
versions of software for each Program Provider.
Go to www.rfmogul.com web site and download to your USB drive the
appropriate software for your program provider.
Place the USB drive into the appropriate slot in the front of the controller and
turn the power ON.
The controller will download the file into memory. This process will take
approximately 8-10 seconds.
SOFTWARE VERSION UPGRADES
When should you think about downloading new software or changing configurations?
1. To take advantage of new innovative features offered by the latest revision of
software.
2. If you have called your installer and he recommends it.
3. If you read the History of the new software and you determine that you could
benefit from its features.
The Eagle Manual
9
Menu Options
Select menu options by
Pressing the POWER or RETURN button once to turn ON the controller. At that time you may press
SEARCH (UP arrow) to begin the search routine or STOW (DOWN arrow) to return the mount to its
stowed or travel position. If you press POWER or RETURN again this will to enter you into the menu
options.
Press the UP ARROW to step through the menu.
When desired function is displayed press the Power or Return Arrow to select that function.
SHUT DOWN
Press the Return Arrow select the SHUT DOWN option and press Return. The power will
turn OFF.
Pressing and holding the Return Arrow for 3 seconds will turn the power OFF.
SEARCH
Press the UP Arrow after turning power ON to begin the satellite search for satellites.
STOW
Press the DOWN Arrow or STOW button after turning power ON to return your mount to
its stowed or travel position.
MANUAL MOTOR MOVEMENT
MOVE AZ
When moving through the menu options and MOVE AZ appears, pressing the RETURN
button will allow you to move or rotate the mount in Azimuth in a clockwise motion by
pressing and holding the UP Arrow and counterclockwise by pressing and holding the
DOWN Arrow.
MOVE EL
When moving through the menu options and MOVE EL appears, pressing the RETURN
button will allow you to elevate the mount by pressing and holding the UP Arrow or by
holding the DOWN Arrow.
MOVE SK
When moving through the menu options and MOVE SK appears, pressing the RETURN
button will allow you to rotate the dish by pressing and holding the UP Arrow to move the
left side of the dish down by holding the DOWN Arrow it will move the right side of the
dish down.
The Eagle Manual
10
Connector Wiring Diagram
Wiring the
12 Pin Controller Connector
Pin Color How Used Where
Used
1 = BLACK Motor -Azimuth
2 = BROWN Motor +Azimuth
3 = RED Motor -Elevation
4 = ORANGE Motor +Elevation
5 = YELLOW Motor - Skew
6 = GREEN Motor +Skew
7 = BLUE Count Azimuth
8 = VIOLET Count Elevation
9 = GRAY Count Skew
10 = WHITE Ground
11 = PINK 12 Volts DC
12 = TAN GPS TXD
RAISING THE ODU
USING A 12 VDC SOURCE
TO RAISE THE MOUNT WITH
A BATTERY
Touch the following wires from the control cable directly to a
drill battery or any 12 VDC source and it will result in movement
of the ODU. To reverse the direction, reverse the wires to your
battery.
ELEVATION Red and Orange will raise and lower
the mount
AZIMUTH Black and Brown will rotate the dish
SKEW Yellow and Green will tilt dish.
Wire Color Wire Function
BLACK +AZ
BROWN -AZ
RED +EL
ORANGE -EL
YELLOW - SKEW
GREEN +SKEW
Otros manuales para Eagle
4
Tabla de contenidos
Otros manuales de Sistema de televisión por satélite de RF Mogul
Manuales populares de Sistema de televisión por satélite de otras marcas
DefineSat
DefineSat VM55 Manual de usuario
Dish Network
Dish Network 112182 Manual de usuario
Thrane&Thrane
Thrane&Thrane sailor 60 Manual técnico
KVH Industries
KVH Industries TracVision L2 Manual de usuario
KVH Industries
KVH Industries TracVision TV1 Manual de usuario
JRC
JRC NJT8304 Series Manual de usuario
Bell
Bell EXPRESSVU Manual de usuario
Promax
Promax SATHUNTER Manual de usuario
SatKing
SatKing PRO MAX Manual de usuario
KVH Industries
KVH Industries TracVision M5 Manual de usuario
KVH Industries
KVH Industries TracVision R5SL Manual de usuario
Dish Network
Dish Network Satellite Television Manual de usuario