Repotec RP-ISF800 Manual de usuario

User Manual

Industrial Fast Ethernet 8 port Ethernet Switch, Power input 12-56VDC, -40°C to 75°C

FCC MARKING

This Equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received;

including interference that may cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to

electromagnetic compatibility, EN 55022 class A for ITE, the essential

protection requirement of Council Directive 2004/108/EC on the

approximation of the laws of the Member States relating to

electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may

be possible that information in this document is not up -to-date. Please

check with your local distributors for the latest information. No part of

this document can be copied or reproduced in any form without written

consent from the company.

Trademarks:

All trade names and trademarks are the properties of their

respective companies.

Power connection

This industrial Fast Ethernet switch comes with a 6 pin terminal block. It can be operated from 12-56VDC

power source. Always Make sure your input voltage is within this supported voltage range for each model.

WARNING –any exceeded input voltage will not make this unit function and may damage this unit.

To make power connection –Follow the printed polarity for V1+, V1-,

V2+, V2-, and ground. Connect positive wire to V+ , connect negative

wire to V-, also connect neutral wire to the ground screw as shown .

Relay -- You may use 24V@1A relay connection to your external device

for special purpose. When 2 powers are connected, the relay is in

OPEN mode. When any power source fails, the relay change to SHORT

status.

Power connecting procedure:

STEP 1 –Pull out 6 pin terminal block.

STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.

STEP 3–Plug back 6 pin terminal block to its place.

WARNING –

Always ground the power source to maintain a clean power input. Due to too many cheap

made power supplies, it creates too much noise, and it will cause the power input fluctuates

when connect to this unit. To avoid this, always ground the power source to gain a clean

power input.

Din Rail Bracket x 1

Wall mount bracket x 2

6 pin Terminal Block x1

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-

mounted bracket are included.

PW1

ON -- when V1+, V1- is connected

LED indicator

PW2

ON -- when V2+, V2- is connected

This unit has no POE feature. the POE amber

LED will always stays in OFF status.

Green LED ---

ON =Link

Flash = TX/RX.

Relay LED Amber

ON one power is connected

OFF two powers are connected

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE802.3x Flow Control and Back Pressure

Switch Architecture

Back-plane (Switching Fabric): 1.6Gbps

Data Processing

Store and Forward

Flow Control:

IEEE 802.3x Flow Control and Back Pressure

MAC address Table Size

Packet Buffer Size

Network Connector :

8xRJ-45 10/100BaseT(X) auto negotiation,

Auto MDI/MDI-X function, Full/Half duplex

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Protocol

CSMA/CD

LED

PW1(Power 1) Green,

PW2(Power 2) Green,

SW(relay) Amber,

TX/RJ-45 port:

LNK (Link/Active) Green,

Housing

Heavy Metal Housing

Reserve polarity protection

Present

Overload current protection

Present

Power Supply

Redundant Dual DC 12V-56V Power Input

Power Consumption

3W@48 VDC full load,

Alarm Relay Contact

Relay outputs with current carrying capacity of 1 A

@24VDC,

Relay in short circuit mode when 2 powers are

connected. in open circuit mode when only one

power supply is connected

POE power

n/a

Removable Terminal Block

Provide 2 Redundant power , Alarm relay contact ,6

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-40℃~75℃fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between

failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L x W x D)

142mmx36.2mmx105mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

Certifications:

EN55022/24

ITE equipment

EN55011

Industrial, Scientific and Medical (ISM) equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

Housing Dimension

Tabla de contenidos

Otros manuales de Cambiar de Repotec

Repotec

Repotec RP-G1416D Manual de usuario

Repotec

Repotec RP-G802W Manual de usuario

Repotec

Repotec RP-G1416Q Manual de usuario

Repotec

Repotec RP-PEG08-H Manual de usuario

Repotec

Repotec RP-G108Q Manual de usuario

Repotec

Repotec RP-IPG402A Manual de usuario

Repotec

Repotec RP-1716DR2 Manual de usuario

Repotec

Repotec RP-IPG814-2F Manual de usuario

Repotec

Repotec RP-G1408Q Manual de usuario

Repotec

Repotec RP-G0401DC Manual de usuario

Repotec

Repotec RP-PG081W Manual de usuario

Repotec

Repotec RP-PE054J/F Manual de usuario

Repotec

Repotec RP-G1416D Manual de usuario

Repotec

Repotec GEL2P-ESW10G Series Manual de usuario

Repotec

Repotec 16 Gigabit L2 Managed Switch Manual de usuario

Repotec

Repotec RP1024W Manual de usuario

Repotec

Repotec 8-P TP+ Manual de usuario

Repotec

Repotec G Series Manual de usuario

Repotec

Repotec GEPOESM-ESW26K Series Manual de usuario

Repotec

Repotec RP-1705K Manual de usuario

Repotec

Repotec GEL2P-ESW26G Manual de usuario

Repotec

Repotec RP-G1510W Manual del operador

Repotec

Repotec RP-G1600U Manual de usuario

Repotec

Repotec RP-PE801 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario