Renogy Monitoring Screen Manual de usuario
Version 1.0
FOR SMART LITHIUM BATTERY SERIES
MONITORING
SCREEN
01
Disclaimer
The manufacturer accepts no liability for any damage caused by:
This manual contains important installation and operation
instructions for your Renogy monitoring screen. Please review
and observe these instructions and keep them located near the
monitoring screen for further reference. The following symbols
are used throughout the manual to indicate potentially
dangerous conditions or important safety information.
Intentional or accidental misuse, abuse, neglect or improper
maintenance, and use under abnormal conditions.
Improper installation, improper operation, and malfunction of
a peripheral device.
Contamination with hazardous substances, diseases,
vermin, or radiation.
Alterations to the product without express written consent
from the manufacturer.
Force majeure: including fire, typhoon, flood, earthquake,
war, and terrorism.
Important Safety Instructions
Please save these instructions.
Indicates a potentially dangerous condition.
Use extreme caution when performing this task.
Indicates a critical procedure for the safe and proper
installation and operation of the monitoring screen.
Indicates a procedure or function that is
important to the safe and proper installation and
operation of the monitoring screen.
NOTE
CAUTION
WARNING
02
General Safety Information
Any uncovered battery material, such as electrolyte or
powder, that has contacted skin or the eyes must be flushed
out with plenty of clean water immediately. Seek medical
attention afterwards. Spillages on clothing should be rinsed
out with water.
DO NOT touch the exposed electrolyte or powder if the
battery casing is damaged.
Please make sure any battery charger(s) or charge controller
(s) are disconnected when working on the battery.
DO NOT connect or disconnect terminals from the battery
without first disconnecting loads.
DO NOT wear jewelry or other metal objects when working
on or around the battery.
DO NOT place tools on top of the battery.
Please keep the battery out of the reach of young children.
Please wear proper protective equipment when working on
the battery.
Please use insulated tools when working on battery.
DO NOT attempt installation while using alcohol or
medication that could impair judgement and/or reaction time.
WARNING
03
CAUTION
Your Renogy monitoring screen is designed for
indoor/compartment installation. DO NOT expose it to direct
sunlight, rain, snow, moisture, or liquids of any type.
DO NOT puncture, drop, crush, burn, penetrate, or strike the
monitoring screen.
The Renogy monitoring screen is only compatible with
Renogy Smart Lithium Iron Phosphate Batteries. DO NOT
attempt to connect the monitoring screen to other batteries or
systems.
DO NOT open, dismantle, or modify the monitoring screen.
If installing in an engine compartment with a gasoline engine,
proper ventilation practices must be used to ensure no
explosive gases are present before installation.
If installing in a compartment with batteries, the compartment
must be properly ventilated to ensure no build-up of
explosive gases prior to installation.
Table of Contents
Important Safety Instructions 01
General Information 05
Product Overview 06
Identification of Parts 06
Dimensions 07
Operation 15
LCD Information 15
Button Operation 19
Troubleshooting 20
Technical Specifications 21
Installation 08
04
05
General Information
Comprehensive Protection
Easy Operation
The Renogy Monitoring Screen for Smart Lithium Battery
Series is a high precision meter designed for Smart Lithium
Iron Phosphate Batteries in off-grid energy storage systems.
Instead of measuring the current flowing in/out of the battery
bank, it can communicate directly with the battery management
system (BMS) and obtain more accurate state of charge (SoC)
readings compared to traditional battery monitors. Other
battery bank information including voltage, current, capacity,
remaining time, error code, and number of paralleled batteries
are also available on the monitoring screen to help users avoid
abnormal conditions and extend the lifetime of battery bank.
Plug and Play
Simply connect the monitoring screen to the battery bank
using an RJ45 communication cable for real-time
monitoring.
Accurate Readings
Obtains battery bank status directly from the battery
management system for precise tracking and prediction.
Shows detailed battery bank information at the push of a
button without the need of system configuration and
calibration.
Displays straightforward error codes for the quick
recognition of potential abnormal conditions and improper
operation.
Key Features
06
Product Overview
LCD Screen
Page Down Button
Page Up Button
Power Button
Front Cover Plate
RJ45 Communication Port
①
②
②
③
③
④
④
⑤
⑥
⑤
⑥
Identification of Parts
①
07
Dimensions
110.0mm
4.3in
87.5mm
3.4in
1.3in
0.8in
2.8in
70.0mm
2.3in
58.5mm
31.8mm
19.5mm
Additional Components
RJ45 Communication Cable
The RJ45 Communication
Cable (5m/16.4ft) is used to
connect the monitoring
screen to the battery bank
for power supply and data
transmission.
Self-tapping Screws (4)
The Self-tapping Screws
(M2.9x13) are used to fix
the monitoring screen on
the mounting surface.
08
3. Cut out a rectangular area for the monitoring screen on the
mounting surface with a jigsaw.
5. Place the monitoring screen into the cut-out area and align the
mounting holes on the monitoring screen with the pre-drilled
screw holes.
6. Affix the monitoring screen on the mounting surface with the
included four self-tapping screws.
7. Re-attach the snap-fit Front Cover Plate to the monitoring screen.
4. Pre-drill four screw holes on the mounting surface with a drill.
Please choose a clean, dry, protected, and easily accessible indoor
location to install the monitoring screen. It is recommended to
mount the monitoring screen at eye level for easy access of
operational controls and battery information. The RJ45
Communication Port on the monitoring screen is accessible from
the back of the unit. Clearance of at least 2 inch (50 mm) behind the
unit is recommended to allow for the bending radius of the RJ45
Communication Cable that connects to the monitoring screen.
Before installing the monitoring screen, it is recommended to have
the following tools available:
Installation
2. Use the monitoring screen as a template to mark the screw holes
and trace the cut-out area on the mounting surface with a pencil.
1. Remove the snap-fit Front Cover Plate from the monitoring screen.
Mounting the Monitoring Screen
Preparation
Choosing an Installation Location
Pencil
Drill
Jigsaw
Phillips screwdriver
09
1
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Instrumento de medición de Renogy
Renogy
Renogy RMS-PGH Manual de usuario
Renogy
Renogy RMS-RVRE Manual de usuario
Renogy
Renogy RMS-DCDC-US Manual de usuario
Renogy
Renogy MT-50 Manual de usuario
Renogy
Renogy ONE Core Manual de usuario
Renogy
Renogy MT-150 Manual de usuario
Renogy
Renogy ONE Core Manual de usuario
Renogy
Renogy MT-1 Manual de usuario
Renogy
Renogy Battery Monitor Manual de usuario
Renogy
Renogy ONE M1 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario