Reiner P3-MP Manual de usuario
GB
P3-MP
Instructions
7
A
1
D
7
2
8
B
3
2
4
5
C
6
5
3
1
Foil pouch
2
Print cartridge
3
Dust cover
4
Safety band
5
Latching wings
6
Rubber seal
7
Print nozzles
8
Printing contacts
8
GB
For your safety
DANGER Warnings about risks where non-observance
of the measures may directly cause death or
serious injury.
WARNING Warnings about risks where non-observance
of the measures may cause death or serious
injury.
CAUTION Warnings about risks where non-observance of
the measures may cause injury.
PLEASE NOTE Warnings about risks where non-observance of
the measures may cause material damage.
Instructions and tips
Safety instructions for MP ink
WARNING
Special ink is highly flammable. Risk of burns!
„ Store at 10 ° C - 20 ° C.
„ Do not expose to direct sunlight.
WARNING
If in eyes.
„ Rinse cautiously with water for several minutes.
„ Remove contact lenses, if present and easy to do.
„ Continue rinsing. Immediately call a POISON CENTER
or doctor/physician.
9
1. Making the print head ready for use
1.1. Opening the pack _Fig. A
„ Cut open foil pouch
1
with shears.
„ Remove printing cartridge
2
.
1.2. Releasing the clip _Fig. B+ C
The print cartridge
2
is supplied with a reusable dust cover
3
.
„ Slightly push apart the latching wings
5
.
„ Remove safety band
4
.
„ Remove printing cartridge.
„ Use the printing cartridge according to the operating
instructions for the device.
2. Printing material
For the best results, use material that is clean, non-greasy, dry
and at the same temperature as the print head.
Polar or polarised surfaces are better suitable on plastics to be
printed on than surfaces with unpolar properties.
Before carrying out a large print job, perform a test print.
10
GB
3. Storage _Fig. A+ B
MP ink is fast-drying. The time it takes the print nozzles
7
to dry up depends on the ambient temperature
and the humidity.
Put the device into the station during short print breaks or
close the nozzle cover.
Observe acoustic signals of the device.
Where the device is not equipped with a nozzle cover, protect
the printing cartridge
2
against drying out with the dust
cover
3
when interrupting work.
To securely close the nozzles
7
of the printing cartridge
2
,
keep the seal at the dust cover
3
free from dirt and dust.
„ Remove the printing cartridge
2
out of the device.
„ Guide the printing cartridge into the dust cover
3
.
„ Push the printing cartridge down until the
latching wings
5
click.
„ Fasten the latching wings with the safety band
4
.
Use the print head within four weeks after opening.
4. Environmental Conditions
Temperature for storage +10° C to +20° C
Temperature for transport -20 ° C to +40 ° C (up to 24
hours)
11
5. Troubleshooting _Fig. D
Dried ink on the print nozzles may result in streaks or reduced
print quality.
5.1. Cleaning mechanism
„ Observe notes on cleaning of the print nozzles
7
in the
operating instructions for the device.
5.2. Cleaning the print head nozzles manually
We recommend the following measure if the cleaning mechanism
does not lead to the desired success:
„ To remove dried ink, press a soft cloth, if necessary lightly
soaked in ethanol (spirits), against the print nozzles
7
for about 3 seconds.
„ Dab off the dissolved ink and wipe the print nozzles dry.
5.3. Cleaning the print head contacts
In rare cases, dirt on the print head contacts may result in inferior
printing results.
„ Clean the contacts
8
on the print head
2
and in the device
with a soft cloth or cotton bud, if necessary lightly soaked
in ethanol (spirits).
Disposal
Directive 2002/96/EC (WEEE)
Old devices must not be disposed of in the common
household waste but in a specified acceptance point
for recycling of electrical and electronic devices.
12
GB
Notes
Award for
Operational
Excellence
Ernst Reiner GmbH & Co. KG
Baumannstr. 16
78120 Furtwangen
Phone +49 7723 657-0
Fax +49 7723 657-200
reiner@reiner.de
|PC-947101-100-1-E|11-2013
Otros manuales para P3-MP
1
Tabla de contenidos
Otros manuales de Impresora de Reiner
Reiner
Reiner jetStamp graphic 970 Manual
Reiner
Reiner jetStamp 1025 Manual de usuario
Reiner
Reiner jetStamp graphic 970 Manual de usuario
Reiner
Reiner speed-i-Marker 940 Manual de usuario
Reiner
Reiner jetStamp 990 Manual de usuario
Reiner
Reiner speed-i-Marker 940 Manual de usuario
Reiner
Reiner speed-i-Jet 798 Manual
Reiner
Reiner speed-i-Marker 940 Manual de usuario
Reiner
Reiner speed-i-Jet 798 Manual de usuario
Reiner
Reiner jetStamp 790 Manual de usuario
Reiner
Reiner 780 Manual de usuario
Reiner
Reiner speed-i-Jet 798 Manual de usuario
Reiner
Reiner speed-i-Jet 798 Manual de usuario
Reiner
Reiner jetStamp 990 Manual de usuario
Reiner
Reiner speed-i-Jet 798 Manual
Reiner
Reiner jetStamp 790 Manual
Reiner
Reiner speed-i-Jet 798 Manual de usuario
Reiner
Reiner jetStamp 1025 Manual de usuario
Reiner
Reiner jetStamp 792 Manual de usuario
Reiner
Reiner P1-MP2-RD Manual de usuario
