Regency GLADIATOR GL3 Manual de usuario

• GLADIATOR (GL3) • with DC motor

• CEILING FAN OWNER'S MANUAL •

01/10

Style that revolves around you.

WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

IMPORTANT SAFEGUARDS:

1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly

before beginning.

2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.

To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.

All

electrical connections must be made in accordance with local codes, ordinances and/or the National Electric

Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a

qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling

members and make the proper installation(s) and connections.

3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades

should be at least 7 feet from floor.

4. When mounting on a ceiling outlet box, an approved box UL listed as "suitable for fan support"

"suitable for fan support"

is required. The

box and its supporting members must be able to support the moving weight of the fan's listed weight. The box

must not be able to twist or work loose. Installation on a concrete ceiling should be performed by qualified

personnel.

5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the

carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure

that you do not mix fan blade sets,

do not mix fan blade sets,

as each blade is part of a weighted set.

6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one

side of the outlet box, and the "HOT" wires on the other side.

7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and

should be installed per the light kit's installation instructions.

8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling

and/or causing damage or injury.

9. The fan can be made to work immediately after installation - the bearings are adequately charged with grease so

that, under normal conditions, further lubrication should not be necessary for the life of the fan.

10. To operate the reverse function on this fan, press the reverse button while the fan is running.

Weight of Fan: 19.3 Lbs

IMPORTANT SAFETY PRECAUTIONS

Thank you for choosing a Regency Ceiling Fan. You have chosen the best!

Your new ceiling fan has been designed to provide many years of service and enjoyment.

• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan

"acceptable for fan

support"

and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support

of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if

in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or

cleaning the fan. Do not insert any objects(s) between rotating fan blades.

NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all

possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness

are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring

for, and operating the unit.

Warnings:

TOOLS AND MATERIALS REQUIRED

• Phillips screwdriver

• Blade screwdriver

• Wrench or pliers

• Wire cutter

• Stepladder

• Wiring supplies as required by

electrical code

UNPACKING YOUR FAN

1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever

necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor

housing on its side, or the decorative housing may shift, be bent or damaged.

2. Examine all parts. You should have the following:

1. Fan blades (5) (Model: TB60-xx, packed in separate box.) (CAUTION: This GLADIATOR (GL3) Ceiling Fan

must only be used with the Models "TB60-xx, W154, W354 and 56" Décor MatchTM" Blades, it is not

intended to be used with any other REGENCY®Fan blades.)

2. Hanging bracket

3. Ceiling canopy

4. Canopy screw cover plate

5. Downrod/ball assembly

6. Decorative collar cover

7. Fan housing with motor (Remove and discard rubber shipping supports around motor, if included on your fan.

Save screws.)

8. Blade arms (5)

9. Detachable switch housing mounting plate

10. Detachable switch housing

11. Transmitter+holder+2 mounting screws

12. Bracket mounting hardware (wood screws, screws, lock washers, washers, wire nuts)

13 and 14. Blade to blade arm screws, w/washers (16) *2 set of screws are provided-a long set and a short set,

depending on which type of blades you choose for your fan.

NOTE: Design of parts shown above may look slightly different for your specific model of fan.

PREPARATION

PREPARATION:

Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor

from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor

box. Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.

Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.

Caution:

To avoid possible electrical shock, be sure

electricity is turned off at the main power box before

wiring. All wiring must be in accordance with National and

Local Electrical Codes and the ceiling fan must be grounded

as a precaution against possible electric shock.

1. Locate ceiling joist where fan is to be mounted, being

sure location agrees with the requirements in the

minimum clearance section of this guide. Wood joist

must be sound and of adequate size to support 35 lbs.

(See Page 1, Items 3 and 4).

2. If not already present, mount a UL listed outlet box

marked "suitable for fan support" following the

instructions provided with the outlet box. The outlet box

must be able to support a minimum of 35 pounds.

3. Attach hanger bracket to outlet box using screws

using screws

provided with the outlet box.

Parts identification on assembled fan

Blade

Arm

Detachable

Switch

Housing

Collar

Cover

Downrod

Canopy

Motor

Housing

INSTALLING THE HANGING BRACKET

Ceiling Fan

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Spring Washer

Fig. 1

INSTALLING THE FAN

1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out)

facing upward.

2. Loosen the two set screws and remove the downrod pin and cotter pin from the top coupling of the motor assembly.

3. Remove ball from the downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin;

remove ball.

4. Feed the wires from top of fan through end of the downrod of choice and set end of downrod into mounting collar so

the hole in the downrod lines up with the hole in the side of the mounting collar.

5. Insert downrod pin through holes in mounting collar and downrod; slip cotter pin through small hole in end of

downrod pin to hold downrod in place.

6. Tighten jam screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod. Tighten

nuts against mounting collar.

NOTE:

Fan has 6 feet of hook-up wire in case

you are using a long extension downrod. Wires

can be cut so only 8 inches or so extend beyond

the top of the downrod to make the electrical

connections easier and safer.

7. Feed wires through collar cover and slide

collar cover down the downrod to top of fan.

8. Feed wires through canopy screw cover plate

and canopy, then slide both over downrod to

lay on top of collar cover. It will be attached

to ceiling later.

9. Feed wires through ball and slide ball over

downrod, past hole in the top end of the

downrod. Insert ball pin (removed in step 3),

slide ball up, and tighten set screw to secure

ball in place.

Hook-up (3)

Wires

Ground

Wire

Ball

Canopy

Canopy Screw

Cover Plate

Downrod

Mounting Collar

Downrod Pin

Top of

Fan Body

Collar Cover

Security Screws

Cotter

Fig. 2

INSTALLING THE FAN

ELECTRICAL CONNECTIONS

WARNING: To avoid damaging the blade arms and blades,

do not install them onto fan until fan is fastened to ceiling.

1. Lift ball/downrod/fan into hanging bracket opening.

NOTE: The tab opposite hanging bracket opening should fit

in slot on ball.

WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before

wiring.

1. Connect the fan supply (black) wire to the black household supply wire as shown in Figure 4.

2. Connect the neutral fan (white) wire to the white neutral household wire. (Fig. 4)

3. After all splices are made, check to make sure there are no loose strands. As an additional precaution we suggest to

secure the plastic wire connectors to the wires with electrical tape.

Slot

Tab

Outlet Box

Black ("AC IN L")

White ("AC IN N")

White (Neutral)

Black (Motor)

Fig. 3

Fig. 4

Green or bare

copper (ground)

Ground (green)

(Connect to ground wire on

hanger bracket if no house

ground wire exists.)

FINISHING THE INSTALLATION

BLADE ATTACHMENT

1. Tuck connections neatly into ceiling outlet box.

2. Slide the canopy up to ceiling and over the 2 screws on

the hanger bracket. Rotate canopy clockwise. Next, while

holding the canopy with one hand, slide the canopy

screw cover plate over the screws and rotate clockwise

until tight. NOTE:

NOTE:

adjust the canopy screws as necessary

until the canopy and canopy screw cover plate are snug.

WARNING:

Make sure the hook on the hanging bracket

properly sits in the groove in the hanger ball before attaching

the canopy to the bracket by turning the housing until it

drops into place.

1. Place fiber washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this

procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 6).

NOTE:

Fans that have painted finishes are packed with gaskets that can be used between the blade arm and blade to

help prevent a clicking noise that may develop if blade screws loosen over time.

2. Tighten each screw starting with center screw.

3. Fasten blade assembly to motor with provided screws and lock lockwashers. Repeat procedure for remaining blades

(Fig. 7). Make sure screws are TIGHT!

TIGHT!

Loose motor screws can contribute to unnecessary hum during operation.

NOTE:

Cordless power screwdrivers are NOT

NOT

recommended, as they tend to strip the heads of the screws and usually

will not fully compress the lock washers on the motor screws. Use a large flat blade screwdriver for final tightening to

fully compress the washers. This will help ensure proper alignment of the blades and noise-free, wobble-free running.

Canopy

Screws

Canopy Screw

Cover Plate

Ceiling Fan

Outlet Box

Hanger

Bracket

Fig. 5

Fig. 6 Fig. 7

Screw Fiber Washer

Blade Arm Blade

Install gasket between

blade arm and blade

(optional)

Screws

Blades Assembly

INSTALLATION OF DETACHABLE SWITCH HOUSING

MOUNTING HUB

1. Remove one of the three screws on the mounting hub located on the fan motor.

2. Loosen the other two screws.

3. Install detachable switch housing mounting hub to mounting hub.

4. Pass the 2 light wires through the center hole of the detachable switch housing mounting hub.

5. Line up the two slotted holes with the two loose screws on the mounting hub located on fan motor.

6. Re-install the third screw removed and tighten all three.

Fig. 8

Light Wires

Mounting Hub

(bottom of motor) Detachable Switch Housing

Mounting Hub

Screws

INSTALLATION OF REMOVABLE SWITCH HOUSING

NOTE: Be sure the power is off before installing.

1. Loosen the 3 side screws on switch housing mounting hub halfway.

2. If installing light kit, carefully remove light kit plug in bottom of switch housing. Attach the light kit to the switch

housing per instructions supplied with light kit. (Follow the instructions included with the kit.)

3. Attach the switch housing to the switch housing hub.

4. Align the side screws with keyhole slots on edge of switch housing and tighten the side screws.

5. Turn the power on. Your Regency Ceiling Fan is now ready to enjoy!

Fig. 9

Light Wires

Switch Housing

Keyhole Slot (x3)

Optional Light Kit

connects to bottom

of Switch Housing

Side Screw (x3)

Detachable Switch Housing

Mounting Hub

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Regency

Regency

Regency ANDROS Manual de usuario

Regency

Regency TROPIC AIR Series Manual de usuario

Regency

Regency Artiste Manual de usuario

Regency

Regency PFLK10 Manual de usuario

Regency

Regency FE-45A Manual de usuario

Regency

Regency BIMINI Manual de usuario

Regency

Regency Regatta Manual de usuario

Regency

Regency Quatro Manual de usuario

Regency

Regency Cabana Manual de usuario

Regency

Regency MX Excel Manual de usuario

Regency

Regency GRAND MARQUIS Manual de usuario

Regency

Regency LX Series Manual de usuario

Regency

Regency Cayman Manual de usuario

Regency

Regency VERA CRUZ Manual de usuario

Regency

Regency INDY Manual de usuario

Regency

Regency NOLA Manual de usuario

Regency

Regency Vantage Manual de usuario

Regency

Regency Orbit Manual de usuario

Regency

Regency Cayman Manual de usuario

Regency

Regency BIMINI Manual de usuario

Regency

Regency Professional Series Manual de usuario

Regency

Regency THE INDOOR/OUTDOOR FAN Manual de usuario

Regency

Regency Celsius Manual de usuario

Regency

Regency Deuce Hugger Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje