Regency Fireplace Products Bellavista B41XTCE Guía de inicio rápido

www.regency-re.com

Bellavista B41XTCE Video

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

• Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Warning

Fire or Explosion Hazard

Failure to follow safety warnings exactly could result in serious

injury, death, or property damage.

Bellavista®B41XTCE

Gas Fireplace

Owners &

Installation Manual

MODELS: B41XTCE-NG11

B41XTCE-LP11

920-035d FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 06.23.20

Installer: Please complete the details on the back cover and leave this

manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Certiﬁed to/Certiﬁé pour: CSA 2.17-2017

ANSI Z21.88-2017

CSA 2.33-2017

Tested by:

2| Regency Bellavista® B41XTCE -11 Gas Fireplace

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The Bellavista™ B41XTCE has been designed

to provide you with all the warmth and charm of a wood ﬁreplace at the ﬂick of a switch. The Bellavista™ B41XTCE

has been approved by Warnock Hersey/Intertek for both safety and efﬁciency. As it also bears our own mark, it

promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a

moment now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.

On Demand Pilot Light (seven day safety timer)

Important information if using the appliance in CPI (continuous pilot mode) only.

This appliance is a ProFlame 1 system ﬁtted with the “On Demand” Pilot, a safety feature which will shut down the gas valve completely by extinguishing

the pilot light in the event of a continuous full seven days of inactivity.

This only applies if the CPI (continuous pilot) switch is in the “on” position.

Each time the main burner shuts down, manually or through the call from the thermostat, the seven day timer starts again.

The seven day inactivity timer is controlled within the circuit board. Therefore, if in CPI mode and when the pilot light is extinguished after seven straight

days of inactivity, the IPI/CPI rocker switch will remain in the “on” position. Therefore, all that is required to relight the pilot would be to press the on/off

button on the remote control transmitter from “on” to “off” and back to “on”. Once the pilot has re-established operation will resume as normal. There is no

requirement to do anything with the IPI/CPI rocker switch.

If the unit never goes as long as seven full days without a call for heat, the pilot will remain lit until it is manually shut-off.

If the unit is being operated in IPI (intermittent pilot) mode, neither the above instructions nor the seven day timer will apply.

See the instructions in this manual and on the Lighting Instructions plate on the appliance to light or re-light the pilot.

Regency Bellavista® B41XTCE -11 Gas Fireplace | 3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency® product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED

GAS FIREPLACE HEATERS ANSI Z21.88-2017 • CSA 2.33-2017 and Gas-ﬁred Appliances for Use at High Altitudes CSA 2.17-2017.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home

Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes

follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current

CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local

codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited

by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

Ensure that structural members are not cut or weakened during installation.

Bellavista

B41XTCE Video

Bellavista B41XT

Gas Fireplace Benets

4| Regency Bellavista® B41XTCE -11 Gas Fireplace

table of contents

MA Code - CO Detector ................................................6

Unit Dimensions ............................................................7

Installation

Installation Checklist ...................................................15

Locating Your Gas Fireplace ........................................15

Clearances ..................................................................16

Mantel Clearances .......................................................17

Mantel Leg Clearances ................................................18

Non-Combustible Requirements..................................18

Framing .......................................................................19

Framing & Finishing .....................................................20

Tile Finish ............................................................20

Clean Finish .........................................................20

Unit Assembly Prior to Installation ...............................22

Top Standoff Assembly ........................................22

Nailing strips .......................................................22

Conversion to Top Vent ................................................23

Venting Introduction .....................................................25

Vent Restrictor & Bafﬂe Installation .............................25

Exterior Vent Termination Requirements .....................26

5" x 8" Rigid Pipe - Cross Reference Chart only ...27-28

Venting Arrangements for Horizontal Terminations - Flex

Vent or Rigid Pipe 5" x 8" ...........................................29

Rear Venting Deﬂector Installation for Rear Vented Hori-

zontal Terminations ......................................................29

Horizontal Terminations ...............................................30

Flex Vent 5" x 8" ..................................................30

Rigid pipe 5" x 8" .................................................31

AstroCap XL & Rigid Rear Vent Kit for Corner in-

stallations - Rigid Pipe 5" x 8" ..............................32

Rigid Pipe Venting Systems - Basic Horizontal & Vertical

Terminations ................................................................33

Venting Arrangements for Horizontal Terminations......34

Horizontal terminations ................................................35

Two (2) 90o Elbows (Rigid Pipe 5" x 8") ...............35

Three (3) 90o Elbows (Rigid Pipe 5" x 8") ............35

Venting Arrangements for Vertical Terminations .........36

Vertical Terminations ...................................................37

Unit Installation with Horizontal Termination

5" x 8" Venting ............................................................38

Unit Installation with Horizontal Termination

5" x 8" Venting .............................................................39

Unit Installation with Vertical Termination

5" x 8" Venting .............................................................40

Gas Line Installation ....................................................40

Pilot Adjustment ...........................................................41

High Elevation ..............................................................41

Gas Pipe Pressure Testing ..........................................41

885 S.I.T. Valve Description .........................................41

Brick Panel Installation ................................................42

Optional Black Enamel Panel Installation ....................43

Log Set Installation ......................................................45

AC Power Adaptor Installation ....................................49

Wiring Diagram ............................................................50

Optional Fan Installation ..............................................51

Wiring Diagram With Optional Fan ..............................53

Optional Wall Thermostat Installation ..........................54

Flush Glass Door Installation .......................................55

Safety Screen ..............................................................55

Operating Instructions

Operating Instructions .................................................56

First Fire ......................................................................56

Normal Operating Sounds of Gas Appliances .............56

Aeration Adjustment ....................................................56

Lighting Procedure ......................................................57

Shutdown Procedure ...................................................57

Copy of Lighting Plate Instructions ..............................58

Maintenance

Maintenance Instructions ............................................59

Log Replacement ........................................................59

Glass Gasket ...............................................................59

Door Glass ...................................................................59

Valve Replacement ......................................................60

Installing Valve .............................................................60

Parts

Main Assembly ............................................................61

Burner Assembly .........................................................62

Warranty

Warranty ......................................................................64

Owner's Information

Installer's Information

On Demand Pilot Light ..................................................2

Manufactured Mobile Home Requirements ...................3

Copy of Safety Decal .....................................................5

Important Message ......................................................8

Before You Start .............................................................8

General Safety Information ............................................8

Lighting Procedure ........................................................9

Shutdown Procedure .....................................................9

Copy of Lighting Plate Instructions ..............................10

Proﬂame I Remote Control Operating Instructions ......11

Warranty .....................................................................64

Regency Bellavista® B41XTCE -11 Gas Fireplace | 5

safety decal

This is a copy of the label that accompanies each Bellavista™ B41XTCE Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.

NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

For the State of Massachusetts, installation

and repair must be done by a plumber or

gas ﬁtter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, ﬂexible con-

nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli-

ances individual manual shut-off must be a

t-handle type valve.

The State of Massachusetts requires the

installation of a carbon monoxide alarm in

accordance with NFPA 720 and a CO alarm

with battery back up in the same room where

the gas appliance is installed.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

511

DOOR SEAL: Please

check that the door is

properly sealed

Minimum Clearances to Combustibles /

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de série

Duplicate S/N

(See Instruction Manual for

detailed instructions)

APPAREIL FONCTIONNANT AU GAZ PROPANE

Modèle B41XTCE-LP11

PROPANE GAS: Model B41XTCE-LP11

NATURAL GAS: Model B41XTCE-NG11

Minimum supply pressure

Manifold pressure high

Manifold pressure low

Orifice size

Minimum input

Maximum input

Altitude

APPAREIL FONCTIONNANT AU GAZ NATUREL

Modèle B41XTCE-NG11

Pression d'alimentation minimale

Pression manifold - élevée

Pression manifold - basse

Taille de l’orifice

D bit calorifique minimal é

D bit calorifique maximalé

Altitude

5.0" WC/C.E. (1.25 kPa)

3.5" WC/C.E. (0.87 kPa)

1.6" WC/C.E. (0.40 kPa)

# 30 DMS

30,000 Btu/h (8.79 kW)

42,500 Btu/h (12.45 kW)

0-4500 ft/pi (0-1372 m)

Pression d'alimentation minimale

Pression manifold - élevée

Pression manifold - basse

Taille de l’orifice

D bit calorifique minimalé

D bit calorifique maximalé

Altitude

11" WC/C.E. (2.74 kPa)

10" WC/C.E. (2..49 kPa)

6.4" WC/C.E. (1.60 kPa)

# 49 DMS

29,500 Btu/h (8.65 kW)

37,500 Btu/h (10.99 kW)

0-4500 ft/pi (0-1372 m)

Minimum supply pressure

Manifold pressure high

Manifold pressure low

Orifice size

Minimum input

Maximum input

Altitude

FPI Fireplace Products International Ltd.

Delta, BC, Canada

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See

owner's manual for details.

Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur.

Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard.

Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure si les

règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.

This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.

For use with glass doors certified with the appliance only À utiliser seulement avec les portes vitrées certifiées avec l'appareil

Electrical supply / Alimentation électrique 115VAC, 1.13 A, 60Hz. Made in Canada/ Fabriqué au Canada

For Use Only with Barrier (Part # 508-100) Follow installation instructions. Utiliser uniquement avec l’écran (n°508-100). Suivre les consignes d'installation.

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. FOYER AU GAZ À ÉVACUATION -

Mantel Clearances from

Fireplace Opening:

(A) Min. 17-9/16" (446mm)

Side Wall Clearance

from Fireplace Opening

B) Min. 9” (229mm)

Ceiling from Top of

Fireplace Opening:

C) 36-5/8” (930mm)

Mantel Depth:

D) Max. 12” (304mm)

Alcove Clearances:

E) Min. Width 60" (1524mm),

F) Max. Depth 36" (914mm)

Minimum Vent Clearances:

Horizontal Top 3" (76mm)

Horizontal Side 2" (51mm)

Horizontal Bottom 2" (51mm)

Vertical Vent 2" (51mm)

Floor

Wall

Ceiling

Part #: 920-034a

Colour: Everything black on grey except indicated items to be printed red.

Size: File at 100% 9.08’’W x 6.231’’H

Material: 2 ml silver matt polyester (DPM SMS)

Jan 16/19: Created draft

Jan 24/19: Rev A - Remodeled decal + added ETL logo at the bottom

*Printer: Continue number sequence from 919-163 - do not restart at 0

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.

Listed/Nom: VENTED GAS FIREPLACE / FOYER AU GAZ À ÉVACUATION

Certified to/Certifi pour: é ANSI Z21.88-2017 • CSA-2.33-2017

CSA 2.17-2017

C #: 4001172

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.

920-034a

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 68.15%

Propane Gas / Gaz propane 68.35%

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

EP5011169

Copy of the safety decal

Decal Location

Remove the faceplate from unit (refer to

manual) the rating plate will be attached

to a black chain as shown below.

DO NOT REMOVE DECAL FROM UNIT.

6| Regency Bellavista® B41XTCE -11 Gas Fireplace

requirements

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for

residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than

seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall

be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled

equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is

installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery

operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure

served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of

qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon

monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of

thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions

shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by

the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or

structure used in whole or in part for residential purposes.

Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the

instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a

Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies

"special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and

detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,

all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of

the installation.

MA Code - CO Detector

(for the State of Massachusetts only)

Regency Bellavista® B41XTCE -11 Gas Fireplace | 7

dimensions

Unit Dimensions

28-1/2"

38-3/8"

22-5/8"

46-11/16"

25-9/16"

16-7/16"

32-5/8"

38-1/4"

36-3/8"

26-3/16"

3-1/4"

49-1/4"

11-5/8"

7-5/16"

1-9/16"

1-1/2"

35"

44-1/4"

3-5/8" 29-1/8"

23-7/16"

38-7/16"

[1185mm]

[974mm]

46-11/16"

[1185mm]

[976mm]

[889mm]

[738mm]

[92mm]

[594mm]

[649mm]

[664mm]

[1251mm]

[38mm]

[1123mm]

[417mm]

[829mm]

[185mm]

[294mm]

[724mm]

[39mm]

[923mm]

[971mm]

[ 9mm]55

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

8| Regency Bellavista® B41XTCE -11 Gas Fireplace

installation

3. See general construction and assembly

instructions. The appliance and vent should

be enclosed.

4. This appliance must be connected to the

speciﬁed vent and termination cap to the

outside of the building envelope. Never vent

to another room or inside a building. Make

sure that the vent is ﬁtted as per Venting

instructions.

5. Inspect the venting system annually for block-

age and any signs of deterioration.

6. Venting terminals shall not be recessed into

a wall or siding.

7. Any safety glass removed for servicing must

be replaced prior to operating the appliance.

8. To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the

ﬁreplace.

9. Wear gloves and safety glasses for protection

while doing required maintenance.

10. Be aware of electrical wiring locations in

walls and ceilings when cutting holes for

termination.

11. Under no circumstances should this appliance

be modiﬁed. Parts that have to be removed

for servicing should be replaced prior to

operating this appliance.

12. Installation and any repairs to this appliance

should be done by a qualiﬁed service person.

A professional service person should be

called to inspect this appliance annually. Make

it a practice to have all of your gas appliances

checked annually.

13. Do not slam shut or strike the glass door.

14. Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.) be

used in this appliance.

15. The appliance area must be kept clear and

free of combustible materials, (gases and

other ﬂammable vapors and liquids).

Important Message

SAVE THESE

INSTRUCTIONS

The B41XTCE-11 Gas Fireplace must be

installed in accordance with these instructions.

Carefully read all the instructions in this manual

ﬁrst. Consult the "authority having jurisdiction"

to determine the need for a permit prior to

starting the installation. It is the responsibility of

the installer to ensure this ﬁreplace is installed

in compliance with manufacturers instructions

and all applicable codes.

Before You Start

Safe installation and operation of this appliance

requires common sense, however, we are

required by the Canadian Safety Standards

and ANSI Standards to make you aware of

the following:

General Safety

Information

1. The appliance installation must conform with

local codes or, in the absence of local codes,

with the current Canadian or National Gas

Codes, CAN1-B149 or ANSI Z223.1 Instal-

lation Codes.

2. The appliance when installed, must be elec-

trically grounded in accordance with local

codes, or in the absence of local codes with

the current National Electrical Code, ANSI/

NFPA 70 or CSA C22.1 Canadian Electrical

Code.

CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE.

CHILDREN AND ADULTS SHOULD

BE ALERTED TO THE HAZARDS OF

HIGH SURFACETEMPERATURES,ES-

PECIALLY THE FIREPLACE GLASS,

AND SHOULD STAY AWAY TO AVOID

BURNS OR CLOTHING IGNITION.

INSTALLATION AND REPAIR SHOULD

BE DONE BY AN AUTHORIZED

SERVICE PERSON. THE APPLIANCE

SHOULD BE INSPECTED BEFORE

USE AND AT LEAST ANNUALLY BY A

PROFESSIONAL SERVICE PERSON.

MORE FREQUENT CLEANING MAY

BE REQUIRED DUE TO EXCESSIVE

LINT FROM CARPETING, BEDDING

MATERIAL, ETC. IT IS IMPERATIVE

THAT CONTROL COMPARTMENTS,

BURNERS AND CIRCULATING AIR

PASSAGEWAYS OF THE APPLIANCE

BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED

OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

WARNING: FAILURETO INSTALLTHIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE

A SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISED WHEN

THEY ARE IN THE SAME AREA AS

THE APPLIANCE. TODDLERS,YOUNG

CHILDREN AND OTHERS MAY BE

SUSCEPTIBLETO ACCIDENTAL CON-

TACTBURNS. A PHYSICALBARRIERS

IS RECOMMENDED IFTHERE ARE AT

RISK INDIVIDUAL IN THE HOUSE. TO

RESTRICT ACCESSTO A FIREPLACE

OR STOVE, INSTALL AN ADJUSTABLE

SAFETY GATE TO KEEP TODDLERS,

YOUNG CHILDREN AND OTHER AT

RISK INDIVIDUALS OUT OFTHE ROOM

AND AWAY FROM HOT SURFACES.

IF THE BARRIER BECOMES

DAMAGED, THE BARRIER

SHALL BE REPLACED WITH THE

MANUFACTURER'S BARRIER FOR

THIS APPLIANCE.

ANY SAFETY SCREEN, GUARD, OR

BARRIER REMOVED FOR SERVICING

THE APPLIANCE, MUST BE

REPLACED PRIOR TO OPERATING

THE APPLIANCE.

A BARRIER DESIGNED TO REDUCE

THE RISK OF BURNS FROMTHE HOT

VIEWING GLASS IS PROVIDEDWITH

THIS APPLIANCE AND SHALL BE

INSTALLED FOR THE PROTECTION

OF CHILDREN AND OTHER AT-RISK

INDIVIDUALS

Regency Bellavista® B41XTCE -11 Gas Fireplace | 9

owner's information

Lighting Procedure

IMPORTANT: The remote control system supplied with this appliance has

several options for starting/operating the appliance using the power button

and ON/OFF key on the hand held transmitter.

Prior to operating this appliance, please read the remote control operating

instructions (packaged with remote control) to understand how to operate

this remote control system. Option to download remote functions video

with QR code below.

1. Ensure the wall switch/receiver is in the remote position. (see Diagram 1).

3. After approximately 4 seconds the spark ignition system will spark for 60

seconds to light the pilot.

4. The unit will turn on.

Note: The ﬁrst try for ignition will last approximately 60 seconds. If there is no

ﬂame ignition (rectiﬁcation) the board will stop sparking for approximately

35 seconds. After wait time , the board will start second try for ignition by

sparking for approximately 60 seconds. If there is still no positive ignition

the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off using ON/OFF switch or press ON/OFF button - if

using remote.

b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF

button if using remote.

c) Repeat step 2.

ON/OFF

Button

Diagram 1

Diagram 2

Set Switch to

Remote

Shutdown Procedure

1. Turn the wall mounted switch or remote to the "OFF" position.

2. Press "OFF" on the remote control.

3. Turn the gas control knob to the "OFF" position to turn off the pilot.

Remote shown in Manual Mode on Hi

Proﬂame

video

2. Press and release the ON/OFF button on the remote handheld transmit-

ter (see Diagram 2). An audible beep should be heard from the receiver.

10 | Regency Bellavista® B41XTCE -11 Gas Fireplace

owner's information

Copy of Lighting Plate Instructions

919-401a

Part #: 919-401a

Colours: Black on Grey, except

for parts indicated as being

Red.

Size: 100%

w- 5.16"

h- 10.3"

June 23/14: Created decal

Sept.29/14: Rev. A - Updated shut-

down procedure.

A) This appliance is equipped with an ignition device which automatically lights the pilot.

Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the ﬂ oor

because some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the ﬁre department.

C) Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service

technician to inspect the appliance and replace any part of the control system and any

gas control which has been underwater.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.

Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT LA MISE EN MARCHE, reniﬂez tout autour de l’appareil pour déceler une odeur de gaz. Reniﬂez au niveau

du plancher, car certains gaz sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne tentez pas d’allumer l’appareil

• Ne touchez à aucun interrupteur; n'utilisez pas de téléphones se trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un téléphone extérieur. Suivez les

instructions du fournisseur.

• Si vous ne pouvez pas rejoindre le fournisseur, appelez le service incendie.

C) N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement. Faites inspecter l’appareil par un tech-

nicien qualiﬁé et remplacez toute partie du système de contrôle et toute commande qui ont été plongés dans l’eau.

DO NOT REMOVE THIS INSTRUCTION PLATE

TO TURN OFF GAS APPLIANCE

This appliance must be installed in accordance with local codes, if any;

if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or

Natural Gas and Propane Installation Codes, CSA B149.1.

CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface

temperatures keep children, clothing and furniture, gasoline and other liquids having ﬂammable

vapors away. Keep burner and control compartment clean. See installation and operating

instructions accompanying appliance.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life. Improper installation, adjustment,

alteration, service or maintenance can cause injury or property damage. Refer to the owner’s

information manual provided with this appliance. For assistance or additional information

consult a qualified installer, service agency or gas supplier.

AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice

risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou

la mort.

Une installation, d'ajustement, de modiﬁcation, de service ou d'entretien peut provoquer

des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de

l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémen-

taires consulter un installateur qualiﬁé, une agence de service ou fournisseur de gaz.

1) Ensure the wall switch/receiver is in the remote position.

2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be

heard from the receiver.

3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4) The unit will turn on.

Note: The ﬁrst attempt to ignition will last approximately 60 seconds. If there is no ﬂame ignition (rectiﬁca-

tion) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a

second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the

second attempt the board will go into lock out.

The system will need to be reset as follows (after going into lock out mode):

a) Wait 5 minutes - turn the system off using ON/OFF switch or press ON/OFF button if using

remote

b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF button if using remote.

c) Unit will repeat step 2.

1) S’assurer que l’interrupteur mural/récepteur soit sur ''Remote''.

2) Appuyer sur la touche ON/OFF de la télécommande puis relâcher. Un bip se fera entendre depuis le

récepteur

3) Après environ 4 secondes, le système d'allumage par étincelles se mettra en marche pendant 60 secondes

pour allumer le brûleur principal.

4) L'appareil s’allume.

Remarque : Au premier allumage, le système tente d’allumer les ﬂammes pendant 60 secondes. Si l’essai

est infructueux, le système fait une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectiﬁcation.

Ce délai écoulé, le système tente à nouveau d'allumer les ﬂammes en produisant des étincelles pendant 60

secondes. Si les ﬂammes ne s’allument toujours pas, le système se met en mode verrouillage.

Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :

a) Attendre 5 minutes puis éteindre l’appareil en utilisant l’interrupteur ou la touche ON/OFF de la

télécommande.

b) Attendre 2 secondes et rallumer le système à l’aide de l’interrupteur ou de la télécommande.

c) L'appareil répètera l'étape 2.

1) Turn the wall mounted switch or remote to the "OFF" position.

2) If service is to be performed–you must disconnect power and shut off gas to the unit.

1) Utiliser l'interrupteur mural ou la télécommande pour mettre le système sur ''OFF''.

2) Lors de l'entretien de l'appareil –débrancher l'alimentation électrique et couper le gaz de l'appareil.

LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

Otros manuales para Bellavista B41XTCE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Regency Fireplace Products

Regency Fireplace Products

Regency Fireplace Products P90-NG10 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Classic H2100M Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products V18M2-NG/LP Instrucciones de funcionamiento

Regency Fireplace Products

Regency Fireplace Products Energy U31 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Classic I2453M Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products City CP60E Series Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products E18 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products P121-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products NARRABRI F100B-1 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Gi29L-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Liberty LRI4E-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products F180B-2 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products HZ54E Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Alterra F175B-2 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900C-NG1 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products U32 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products IG34-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900L Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products P36-NG4 Natural Gas Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products I31-NG3 Manual de servicio

Regency Fireplace Products

Regency Fireplace Products F1100S Manual de servicio

Regency Fireplace Products

Regency Fireplace Products Cascades I1500 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Bellavista B36XTCE-10 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products U900E-NG11 Guía de inicio rápido

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación