Regency Fireplace Products U900E-NG11 Guía de inicio rápido

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

920-007e 05.27.21

www.regency-ﬁre.com

Regency Ultimate™U900E

Gas Fireplace

Owners &

Installation Manual

MODELS: U900E-NG11 Natural Gas

U900E-LP11 Propane

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Certiﬁed to/Certiﬁé pour: CSA 2.17-2017

ANSI Z21.88-2017

CSA 2.33-2017

Tested by:

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appli-

ance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Warning

Fire or explosion Hazard

failure to follow safety warnings exactly could result in serious

injury, death, or property damage.

2| Regency Ultimate™ U900E-11 Gas Fireplace

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with

other gases unless a certiﬁed kit is used.

This appliance may be installed as an OEM installation in a manufactured home (USA only) or mobile home and must be

installed in accordance with the manufacturer's instruction and the Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280, in the Untied States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH, in

Canada.

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency® product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following standards: to

Vented Gas Fireplace Heaters ANSI Z21.88-2017 • CSA 2.33-2017 and Gas-ﬁred Appliances for Use at High Altitudes CSA

2.17-2017.

This appliance may only be installed in an aftermarket permanently located, manufactured home (U.S.A only) or mobile home,

where not prohibited by local codes.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria

for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home

Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence

of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA

70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1

in Canada.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as

applicable to local codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

Ensure that structural members are not cut or weakened during installation.

Regency Ultimate™ U900E-11 Gas Fireplace | 3

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The U900E has been designed to provide

you with all the warmth and charm of a ﬁreplace at the ﬂick of a switch. The model U900E has been approved by

Warnock Hersey/Intertek for both safety and efﬁciency. As it also bears our own mark, it promises to provide you

with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint

yourself with these instructions and the many features of your Regency® Fireplace.

ON DEMAND PILOT LIGHT (SEVEN DAY SAFETY TIMER)

Important information if using the appliance in CPI (continuous pilot mode) only

This appliance is a ProFlame 2 system ﬁtted with the “On Demand” Pilot, a safety feature which will shut down the gas valve completely

by extinguishing the pilot light in the event of a continuous full seven days of inactivity.

This only applies if the CPI (continuous pilot) switch is in the “on” position in your remote control transmitter.

Each time the main burner shuts down, manually or through the call from the thermostat, the seven day timer starts again.

The seven day inactivity timer is controlled within the circuit board. Therefore, if in CPI mode and when the pilot light is extinguished

after seven straight days of inactivity, the CPI setting on the remote control transmitter will remain in the “CPI” (continuous pilot) position.

Therefore, all that is required to relight the pilot would be to press the on/off button on the remote control transmitter from “on” to “off” and

back to “on”. Once the pilot has re-established operation will resume as normal. There is no requirement to do anything with the IPI/CPI

mode on the remote control transmitter.

If the unit never goes as long as seven full days without a call for heat, the pilot will remain lit until it is manually shut-off.

If the unit is being operated in IPI (intermittent pilot) mode, neither the above instructions nor the seven day timer will apply.

See the instructions in this manual and on the Lighting Instructions plate on the appliance to light or re-light the pilot.

4| Regency Ultimate™ U900E-11 Gas Fireplace

table of contents

On Demand Pilot Light (seven day safety timer) ............................3

Copy of Safety Decal ......................................................................5

Decal location .................................................................................5

Important Message .......................................................................7

Before You Start ..............................................................................7

General Safety Information .............................................................7

Lighting Procedure .........................................................................8

Shutdown Procedure ......................................................................8

Copy of the Lighting Plate Instructions ...........................................9

Proﬂame II Remote Control Operating Instructions ........................10

Installation Checklist .......................................................................14

Locating Your Gas Fireplace ...........................................................14

Heatwave

Duct System .............................................................................14

MA Code - CO Detector .................................................................15

Clearances .....................................................................................16

Mantel Clearances ..........................................................................17

Mantel Leg Clearances ...................................................................17

Unit Assembly Prior To Installation .................................................18

Nailing Strips ..................................................................................18

Installation Access panel ................................................................18

Framing Dimensions .......................................................................19

Optional Framing kit ........................................................................20

Horizontal vent deﬂector installation ...............................................21

Wall mount On / Off Switch and battery holder installation ............22

Non-Combustible Requirements.....................................................23

Non-combustible facing installation ...............................................23

Framing & Finishing ........................................................................24

Exterior Vent Termination Requirements ........................................26

Vent Restrictor Setting ....................................................................27

Venting ............................................................................................28

Direct Vent System (Flex) .............................................................28

4” x 6-5/8” Rigid Pipe .....................................................................29

Cross Reference Chart only ...........................................................29

Rigid Pipe Venting Systems ............................................................31

Venting Introduction ........................................................................32

Venting Arrangement for Horizontal Terminations ..........................32

Venting Arrangement for Vertical Terminations ...............................33

Vertical Termination -Co-linear Flex System ..................................36

Venting Arrangements - Vertical Termination ..................................37

with Co-linear Flex System for both ................................................37

Residential & Manufactured Homes into Masonry Fireplaces ........37

Unit Installation with Horizontal Termination ..................................38

4" x 6-5/8" venting ..........................................................................38

owner's information

installer's information

Unit Installation with Horizontal Termination ..................................39

Dura-Vent Horizontal terminations ..................................................40

unit installation with Vertical Termination ........................................41

4" x 6-5/8" venting ..........................................................................41

Vertical ﬂue extension kit (part #946-756) ......................................43

Ceiling Firestop / ﬁrestop spacer (part #946-757) ..........................43

High Elevation .................................................................................44

Gas Line .........................................................................................44

Installation ......................................................................................44

Pilot Adjustment ..............................................................................44

Gas Pipe Pressure Testing .............................................................44

885 S.I.T. Valve ..............................................................................44

Description......................................................................................44

Aeration Adjustment .......................................................................45

Wiring Diagram ...............................................................................46

log set installation ...........................................................................47

Front trim removal / Installation ......................................................49

Inner panel removal / Installation ....................................................49

Screen & inner Door frame Installation ...........................................50

Glass surround installation .............................................................51

Optional ﬁnishing trim installation ...................................................51

Faceplate installation ......................................................................52

First Fire .........................................................................................53

Operating Instructions ....................................................................53

Coding/Pairing of remote control transmitter with on/off switch ......53

Lighting Procedure .........................................................................54

Shutdown Procedure ......................................................................54

Copy of the Lighting Plate Instructions ..........................................55

Normal Operating Sounds of Gas Appliances ................................56

Maintenance Instructions................................................................56

Glass Gasket ..................................................................................57

Glass Door ......................................................................................57

Glass Replacement ........................................................................57

General Vent Maintenance .............................................................57

Fan Service ....................................................................................58

Glass door removal.........................................................................59

Valve Tray Replacement .................................................................60

Gas Maintenance ...........................................................................61

Main Assembly ...............................................................................62

Accessories ....................................................................................63

Warranty .........................................................................................66

Regency Ultimate™ U900E-11 Gas Fireplace | 5

safety decal

This is a copy of the label that accompanies each U900E-NG and U900E-LP Direct Vent Gas Fireplace. We have printed a copy of the contents here for your

review.

NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

COPY OF SAFETY DECAL

For the State of Massachusetts, installation

and repair must be done by a plumber or

gasﬁtter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, ﬂexible con-

nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli-

ances individual manual shut-off must be a

t-handle type valve.

The State of Massachusetts requires the

installation of a carbon monoxide alarm in

accordance with NFPA 720 and a CO alarm

with battery back up in the same room where

the gas appliance is installed.

Part #: 920-006a

Colour: Black on grey except what is indicated as being printed red.

Size: (File at 100%) 9.3"w x 6.05"h

Material: 2 ml silver matt polyester (DPM SMS)

Dec 19/18: Created draft

Jan. 24/19: Rev A - Remodeled decal + added ETL logo at the bottom

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

504

DOOR SEAL: Please

check that the door is

properly sealed

FPI Fireplace Products International Ltd. Delta, BC, Canada

Minimum Clearances to Combustibles /

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de Série

Electrical supply / Alimentation électrique 115VAC, 1.13 A, 60Hz.

Fan Part # 910-157/P

Made in Canada/ Fabriqué au Canada

Duplicate S/N

(See Instruction Manual for

detailed instructions)

(Voir manuel pour plus de détails)

APPAREIL FONCTIONNANT AU GAZ PROPANE

CONÇU POUR FOYER :

Modèle U900E-LP

PROPANE GAS: Model U900E-LP11

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

APPAREIL FONCTIONNANT AU GAZ NATUREL

CONÇU POUR FOYER : Modèle U900E-NG11

5.0" WC/C.E. (1.25 kPa)

3.5" WC/C.E. (0.87 kPa)

1.6" WC/C.E. (0.40 kPa)

# 35 DMS

34,000 Btu/h (9.96 kW)

23,500 Btu/h (6.89 kW)

0-4500 ft/pi (0-1372 m)

11" WC (2.73 kpa)

10" WC/C.E. (2.49 kPa)

6.4" WC/C.E. (1.60 kPa)

# 52 DMS

31,500 Btu/h (9.23kW)

25,000 Btu/h (7.33 kW)

0-4500 ft/pi (0-1372 m)

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

Side Walls / Murs latéraux

A 8” (203 mm)

Ceiling / Plafond

B 48” (1219 mm)

Min. Mantel Height / Hteur Min Manteau

C 20" (508 mm)

Max. Mantel Depth / Prof. Max Manteau

D 12” (305 mm)

Alcove Width / Largeur Alcôve

E 84" (1524 mm)

Alcove Depth / Profondeur Alcôve

F 36" (2134 mm)

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles

This appliance is only for use with the type(s) of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by

local codes. See owner's manual for details. This appliance is supplied with a conversion kit.

L'appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation National Fuel Gas Code ANSI Z223.1, ou CSA-B149.1 Natural Gas and

Propane Installation Code en vigueur.

L'appareil doit être installé conformément à la norme CAN/CSA-Z240, Série MM, Maisons mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction

and Safety Standard. Si ces normes ne sont pas applicables, veuillez vous référer à la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C

Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec les types de gaz indiqués sur la plaque signalétique et peut être installé dans une maison préfabriquée (É.-U. seulement) ou mobile installée à demeure si les règlements

locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Une trousse de conversion est fournie avec cet appareil.

Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si une trousse de conversion certifiée est fournie.

For Use Only with Barrier (Part # 466-111) Follow installation instructions. Utiliser uniquement avec l’écran (n°466-111). Suivre les consignes d'installation.

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximal é

D bit calorifique minimalé

Altitude

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximalé

D bit calorifique minimalé

Altitude

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. FOYER AU GAZ À ÉVACUATION -

Part No. 946-753 register kit may be used. La trousse de registre (pièce n 946-753) peut être utilisée.

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.

Listed/Nom: VENTED GAS FIREPLACE / FOYER AU GAZ À ÉVACUATION

Certified to/Certifi : é

ANSI Z21.88-2017 • CSA-2.33-2017

CSA 2.17-2017

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.

C #: 4001172

NATURAL GAS: Model U900E-NG11

920-006a

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 68.28%

Propane Gas / Gaz propane 69.49%

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

EP5011169

DECAL LOCATION

Remove outer faceplate and door (see manual for

instructions) once the Faceplate and Glass door have

been removed the rating plate will be attached to a chain.

DO NOT REMOVE DECAL FROM UNIT.

6| Regency Ultimate™ U900E-11 Gas Fireplace

dimensions

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

Outer Faceplate size - 43-1/16" W x 25-1/4" H

Glass Surround size - 47" W x 25-1/4" H

Finishing Trim (Clean Edge Design) size - 40-1/8" W x 18-1/4" H

Steel header on edge

Reference Description Inches/Millimeters

I Gas Connection Opening Height 1-11/16" (43mm)

J Gas Connection Height 2-11/16" (67mm)

K Gas Connection Inset 1-1/8" (29mm)

L Gas Connection Opening Width 4-11/16" (119mm)

Note: Gas connection is from the right or left side of the appliance, and electrical connection is on the left side of the appliance. A

metal receptacle box is supplied/installed with the appliance to make all 120 volt electrical connections.

Regency Ultimate™ U900E-11 Gas Fireplace | 7

owner's information

4. This appliance must be connected to the

speciﬁed vent and termination cap to the outside

of the building envelope. Never vent to another

room or inside a building. Make sure that the

vent is ﬁtted as per Venting instructions.

5. Inspect the venting system annually for blockage

and any signs of deterioration.

6. Venting terminals shall not be recessed into a

wall or siding.

7. Any safety glass removed for servicing must

be replaced prior to operating the appliance.

8. To prevent injury, do not allow anyone who is

unfamiliar with the operation to use the ﬁreplace.

9. Wear gloves and safety glasses for protection

while doing required maintenance.

10. Be aware of electrical wiring locations in walls

and ceilings when cutting holes for termination.

11. Under no circumstance should this appliance

be modiﬁed. Parts that have to be removed for

servicing should be replaced prior to operating

this appliance.

12. Installation and any repairs to this appliance

should be done by a qualiﬁed service person.

A professional service person should be called

to inspect this appliance annually. Make it a

practice to have all of your gas appliances

checked annually.

13. Do not slam shut or strike the glass door.

14. Under no circumstances should any solid fuels

(wood, paper, cardboard, coal, etc.) be used in

this appliance.

15. The appliance area must be kept clear and

free of combustible materials, (gases and other

ﬂammable vapours and liquids).

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The Gas Fireplace must be installed in accordance

with these instructions. Carefully read all the

instructions in this manual ﬁrst. Consult the "authority

having jurisdiction" to determine the need for a permit

prior to starting the installation. It is the responsibility

of the installer to ensure this ﬁreplace is installed

in compliance with manufacturers instructions and

all applicable codes.

BEFORE YOU START

Safe installation and operation of this appliance

requires common sense, however, we are required

by the Canadian Safety Standards and ANSI

Standards to make you aware of the following: CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE.

CHILDREN AND ADULTS SHOULD BE

ALERTED TO THE HAZARDS OF HIGH

SURFACE TEMPERATURES, ESPE-

CIALLY THE FIREPLACE GLASS, AND

SHOULD STAY AWAYTO AVOID BURNS

OR CLOTHING IGNITION.

GENERAL SAFETY

INFORMATION

1. The appliance installation must conform with

local codes or, in the absence of local codes, with

the current Canadian or National Gas Codes,

CAN1-B149 or ANSI Z223.1 Installation Codes.

2. The appliance when installed, must be

electrically grounded in accordance with local

codes, or in the absence of local codes with the

current National Electrical Code, ANSI/NFPA 70

or CSA C22.1 Canadian Electrical Code.

3. See general construction and assembly

instructions. The appliance and vent should be

enclosed.

INSTALLATION AND REPAIR SHOULD

BE DONE BY AN AUTHORIZED

SERVICE PERSON. THE APPLIANCE

SHOULD BE INSPECTED BEFORE

USE AND AT LEAST ANNUALLY BY A

PROFESSIONAL SERVICE PERSON.

MORE FREQUENT CLEANING MAY

BE REQUIRED DUE TO EXCESSIVE

LINT FROM CARPETING, BEDDING

MATERIAL,ETC.IT IS IMPERATIVETHAT

CONTROLCOMPARTMENTS,BURNERS

AND CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED

OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE A

SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE

IN THE SAME AREA AS THE APPLI-

ANCE. TODDLERS,YOUNG CHILDREN

AND OTHERS MAY BE SUSCEPTIBLE

TO ACCIDENTAL CONTACT BURNS. A

PHYSICAL BARRIERS IS RECOMMEND-

ED IFTHERE ARE AT RISK INDIVIDUAL

INTHE HOUSE. TO RESTRICT ACCESS

TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO

KEEP TODDLERS, YOUNG CHILDREN

AND OTHER AT RISK INDIVIDUALS OUT

OF THE ROOM AND AWAY FROM HOT

SURFACES.

A BARRIER DESIGNED TO REDUCE

THE RISK OF BURNS FROM THE HOT

VIEWING GLASS IS PROVIDED WITH

THIS APPLIANCE AND SHALL BE

INSTALLED FOR THE PROTECTION

OF CHILDREN AND OTHER AT-RISK

INDIVIDUALS

IFTHE BARRIER BECOMES DAMAGED,

THE BARRIER SHALL BE REPLACED

WITHTHE MANUFACTURER'S BARRIER

FOR THIS APPLIANCE.

ANY SAFETY SCREEN, GUARD, OR

BARRIER REMOVED FOR SERVICING

AN APPLIANCE MUST BE REPLACED

PRIORTOOPERATINGTHEAPPLIANCE.

8| Regency Ultimate™ U900E-11 Gas Fireplace

owner's information

* Not offered on all models.

IMPORTANT: The remote control system supplied with this appliance has

several options for starting/operating the appliance using the battery holder

and ON/OFF key on the hand held transmitter.

Prior to operating this appliance, please read the remote control operating

instructions (packaged with remote control) to understand how to operate

this remote control system.

1. Ensure the battery holder switch is in the Remote position and / or wall

mounted battery holder (if equipped) is in the <REMOTE> position.

2. Press and release the ON/OFF button on the remote handheld transmitter

(see Diagram 1). An audible beep should be heard from the receiver. If

not using the remote, the unit can also be turned on by sliding the battery

holder switch to the <ON> position (if equipped).

Note: The ﬁrst try for ignition will last approximately 60 seconds. If there is no

ﬂame ignition (rectiﬁcation) the board will stop sparking for approximately

35 seconds. After wait time , the board will start second try for ignition by

sparking for approximately 60 seconds . If there is still no positive ignition

the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off by pressing the ON/OFF button on the remote.

b) Wait 5 minutes then repeat from step 2.

SHUTDOWN PROCEDURE

1. Press the ON/OFF button on the remote

2. If service is to be performed- you must disconnect power and shut off gas

to the unit.

ON/OFF Button

Diagram 1

Remote shown in Manual Mode on Hi

3. After approximately 4 seconds the spark ignition system will spark for 60

seconds to light the pilot.

4. The unit will turn on.

LIGHTING PROCEDURE

Fan Operation: The standard fan can be operated by using the remote control

supplied with this unit. See remote control instructions.

Note: In thermostat mode: When the appliance is turned on, the fan will not

come on for the ﬁrst 5 minutes (if fan is turned on). When the appliance is

turned off the fan will not turn off for 12 minutes (if in on position)

Manual mode: Fan will turn on and off immediately using the remote control

transmitter if the fan function is in the "on" position.

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection

See remote control instructions for details.

On Demand Pilot (seven day safety timer)

Important information if using the appliance in CPI (continuous pilot mode) only

This appliance is a ProFlame 2 system ﬁtted with the “On Demand” Pilot, a safety feature which will shut down the gas valve completely by extinguishing the

pilot light in the event of a continuous full seven days of inactivity.

This only applies if the CPI (continuous pilot) switch is in the “on” position in your remote control transmitter.

Each time the main burner shuts down, manually or through the call from the thermostat, the seven day timer starts again.

The seven day inactivity timer is controlled within the circuit board. Therefore, if in CPI mode and when the pilot light is extinguished after seven straight days

of inactivity, the CPI setting on the remote control transmitter will remain in the “CPI” (continuous pilot) position. Therefore, all that is required to relight the pilot

would be to press the on/off button on the remote control transmitter from “on” to “off” and back to “on”. Once the pilot has re-established operation will resume

as normal. There is no requirement to do anything with the IPI/CPI mode on the remote control transmitter.

If the unit never goes as long as seven full days without a call for heat, the pilot will remain lit until it is manually shut-off.

If the unit is being operated in IPI (intermittent pilot) mode, neither the above instructions nor the seven day timer will apply.

See the instructions in this manual and on the Lighting Instructions plate on the appliance to light or re-light the pilot.

Regency Ultimate™ U900E-11 Gas Fireplace | 9

owner's information

COPY OF THE LIGHTING PLATE INSTRUCTIONS

919-649

Part #: 919-649

Colours: Black on Grey, except for parts indicated as being Red.

Punch out .25" hole top right corner where indicated.

Size: 100%

w- 6.52"

h- 11.13"

Apr 05/16: Created decal

Apr. 26/16: Added Fr. Headers/warnings

w- 6.5"

h- 11"

A) This appliance is equipped with an ignition device which automatically lights the pilot.

Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the oor

because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

C) Do not use this appliance if any part has been under water. Immediately call a qualied service

technician to inspect the appliance and replace any part of the control system and any

gas control which has been underwater.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.

Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT LA MISE EN MARCHE, reniez tout autour de l’appareil pour déceler une odeur de gaz. Reniez au niveau du plancher, car certains gaz

sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne tentez pas d’allumer l’appareil

• Ne touchez à aucun interrupteur; n'utilisez pas de téléphones se trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un téléphone extérieur. Suivez les instructions du fournisseur.

• Si vous ne pouvez pas rejoindre le fournisseur, appelez le service incendie.

C) N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement. Faites inspecter l’appareil par un technicien qualié et remplacez

tout élément du système de contrôle ou de commande qui a été plongé dans l’eau.

DO NOT REMOVE THIS INSTRUCTION PLATE

NE PAS ENLEVER CETTE ÉTIQUETTE D’INSTRUCTIONS

TO TURN OFF GAS APPLIANCE / POUR ÉTEINDRE UN APPAREIL AU GAZ

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54,

or Natural Gas and Propane Installation Codes, CSA B149.1.

Cet appareil doit être installé conformément aux codes locaux, s’il y a lieu. En l’absence de tels codes, suivre le National Fuel Gas Code,

ANSI Z223.1/NFPA 54, ou les Natural Gas and Propane Installation Codes, CSA B149.1.

CAUTION: Hot while in operation. Do not touch. Severe burns may result. Due to high surface temperatures keep

children, clothing and furniture, gasoline and other liquids having ammable vapors away. Keep burner and control

compartment clean. See installation and operating instructions accompanying appliance.

ATTENTION : Surfaces chaudes lorsque l’appareil est en marche. Ne pas toucher. Risque de brûlures graves. En raison

des températures élevées, les enfants, les vêtements et le mobilier, le carburant et tout autre liquide aux vapeurs

inammables doivent être tenus éloignés de l’appareil. Nettoyer régulièrement le brûleur et le compartiment des

commandes. Voir les consignes d’installation et d’utilisation fournies avec l’appareil.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional

information consult a qualified installer, service agency or gas supplier.

AVERTISSEMENT : Quiconque ne respecte pas scrupuleusement les instructions de la présente notice risque de déclencher

un incendie ou une explosion pouvant entraîner des dégâts matériels ou des blessures pouvant être mortelles.

Tout défaut d'installation, de réglage, de modication, de service ou d'entretien peut entraîner des blessures ou des dom-

mages matériels. Reportez-vous au manuel d'utilisation fourni avec cet équipement. Pour obtenir de l'aide ou des informa-

tions complémentaires, consulter un installateur ou un service d'entretien qualié, ou le fournisseur de gaz.

1) Ensure the Main switch is in the ON position and/or the wall mounted battery holder (if equipped) is in the <REMOTE> position.

2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be heard from the receiver. If not

using the remote, the unit can also be turned on by sliding the battery holder switch to the <ON> position (if equipped).

3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4) The unit will turn on.

Note: The rst attempt to ignition will last approximately 60 seconds. If there is no ame ignition (rectication) the board will stop spark-

ing for approximately 35 seconds. After this wait time, the board will start a second try for ignition by sparking for approximately 60

seconds. If there is still no positive ignition after the second attempt the board will go into lock out.

The system will need to be reset as follows (after going into lock out mode):

a) Wait 5 minutes - turn the system o󰀨 by pressing the ON/OFF button on the remote.

b) After approximately 2 seconds press the ON/OFF button again.

c) Unit will repeat step 2.

1) S’assurer que le commutateur principal est en position ON et/ou que le bloc-piles mural (le cas échéant) est en position <REMOTE>.

2) Appuyer sur la touche ON/OFF de la télécommande puis relâcher. Un bip sonore retentira depuis le récepteur. Si vous n'utilisez pas

la télécommande, l'appareil peut également être allumé en faisant glisser le commutateur du bloc-piles sur la position <ON> (le cas

échéant).

3) Après environ 4 secondes, le système d'allumage produira une étincelle pendant 60 secondes pour allumer le brûleur principal.

4) L'appareil s’allumera.

Remarque : Au premier allumage, le système tente d’allumer les ammes pendant 60 secondes. Si l’essai est infructueux, le système

fera une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectication. Ce délai écoulé, le système tente à nouveau d'allumer les

ammes en produisant des étincelles pendant 60 secondes. Si les ammes ne s’allument toujours pas, le système se met en mode ver-

rouillage.

Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :

a) Attendre 5 minutes et éteindre l’appareil en appuyant sur la touche ON/OFF de la télécommande.

b) Attendre 2 secondes et appuyer encore une fois sur la touche ON/OFF.

c) L'appareil répètera l'étape 2.

1) Press the ON/OFF button on the remote.

2) If service is to be performed–you must disconnect power and shut off gas to the unit.

1) Appuyer sur la touche ON/OFF de la télécommande.

2) Lors de l'entretien de l'appareil, vous devez débrancher l'alimentation électrique et couper le gaz alimentant l'appareil.

LIGHTING INSTRUCTIONS / CONSIGNES D’ALLUMAGE

FOR YOUR SAFETY READ BEFORE LIGHTING

POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE

10 | Regency Ultimate™ U900E-11 Gas Fireplace

owner's information

PROFLAME II REMOTE CONTROL OPERATING INSTRUCTIONS

Figure 2: Transmitter LCD Display

OPERATING PROCEDURE

Initializing the System for the First Time

Power the receiver. Press the PRG button located on the top right hand

corner of receiver. The receiver will beep three times to indicate that it

is ready to synchronize with a transmitter. Install the 3 AAA type batter-

ies in the transmitter battery bay, located on the base of the transmitter

(ﬁg. 3). With the batteries already installed in the transmitter, opush

the ON button. The receiver's command is accepted and sets to the

particular code of that transmitter. The system is now initialized.

(*) The receiver may be independent or integral jto the IFC hearth appli-

ance control module. The receiver instruction may not be independent

when part of the IFC.

Figure 3: Battery Compartment

WARNING: THE TRANSMITTER AND IFC ARE RADIO FRE-

QUENCY DEVICES.

The Proﬂame 2 Transmitter provides for controlling the following hearth

appliance functions:

1. Main Burner On/Off

2. Main Burner ﬂame modulation (6 levels)

3. Choice of standing or intermittent pilot (CPI/IPI)

4. Thermostat and Smart thermostat functions

5. Accent light modulation (6 levels)**

6. Split ﬂow valve**

7. Comfort Fan speed modulation (6 levels)**

** This feature is not available on any Hampton models.

IMPORTANT:The Proﬂame Transmitter 2 is an integrated part of the

Proﬂame 2 System, which consists of these elements:

• Proﬂame 2 Transmitter, to be used in conjunction with:

• Integrated Fireplaces Control (Proﬂame 2 IFC)

The Proﬂame Transmitter uses a streamline design with a simple button

layout and informative LCD display (Fig. 1). A Mode Key is provided to

index between the features and a Thermostat Key is used to turn on/off

or index through Thermostat functions (Fig. 1 & 2). Additionally, a Key

Lock feature is provided (Fig. 22).

TECHNICAL DATA

REMOTE CONTROL

Supply Voltage 4.5V (three 1.5V AAA batteries)

Ambient temperature

ratings

0 - 50oC (32 - 122oF)

Radio Frequency 315 MHZ

ATTENTION!

- Turn “OFF” the main gas supply of the appliance during installation or

maintenance of the IFC.

- Turn “OFF” main gas supply to the appliance prior to removing or

reinserting the batteries.

- In case of remote control malfunction, turn off the IFC device using

the "ON/OFF" main switch.

- For installation / maintenance, switch off the IFC device removing

main power supply plug.

Figure 1: Proﬂame Transmitter

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Regency Fireplace Products

Regency Fireplace Products

Regency Fireplace Products P36D-NG1 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Panorama P36 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Classic H2100M Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products LRI3E-LP1 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Bellavista B36XTCE Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Grandview G600C-1 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products HZ54E Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Horizon HZ40E-NG10 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products City Series Manual de usuario

Regency Fireplace Products

Regency Fireplace Products Horizon HZO42-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products City Series Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Regency Gi29LU Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products P36-NG4 Natural Gas Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products CF780 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Bellavista B36XTCE-10 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900L Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Gi29LE Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products P42 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Greenfire GFi350LNG-R Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900C-NG2 Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products GEM54-NG Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products DVi34L Series Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Classic I2450M Guía de inicio rápido

Regency Fireplace Products

Regency Fireplace Products Energy U31-NG10 Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación