Redline Communications RedCONNEX AN-80i Manual de usuario

AN-80i

Advanced Broadband Wireless

Infrastructure Solutions

Quick Install Guide

1 Safety Notices

1. Do not exceed the described limits on product labels. Position power cords to avoid

damage. Do not overload wall outlets. Protect equipment by disconnecting power when

not in use.

2. Do not place PoE power adaptor on or near a direct heat source or operate near water

or in a wet location. Disconnect the PoE power before cleaning and use only a damp

cloth for cleaning. Do not use liquid or aerosol cleaners.

3. The AN-80i unit must not be located near power lines or other electrical power circuits.

4. The AN-80i must be properly grounded to protect against power surges and

accumulated static electricity. It is the user's responsibility to install this device in

accordance with the local electrical codes and building codes: grounding of the

transceiver unit, mast, lead-in wire and discharge unit, location of discharge unit, size of

grounding conductors and connection requirements for grounding electrodes.

2 Important Service Information

1. Refer all repairs to qualified service personnel. Do not remove the covers or modify any

part of this device, as this voids the warranty.

2. Locate the serial numbers and record these on your registration card for future

reference. Record the MAC address located on the AN-80i.

3AN-80i User Documentation

The RDL-80i system user manuals are available online at Redline Partner support portal. If you

can not access the Redline support portal directly, contact your Redline partner or sales

representative to obtain electronic copies of the RDL-3000 system documentation (Adobe PDF

format).

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

4 Test Overview

This Quick Install Guide provides steps for basic configuration and operational testing of

an AN-80i PTP link. This procedure assumes a setup consisting of two complete AN-80i

units. Refer to the AN-80i User Manual and Installation Guidelines for additional safety

instructions and for specific operational and installation details.

4.1 Required Test Facilities

You will require the following to perform these tests:

1. Identify the RF channel(s) to be used.

2. Obtain a valid Options Key for each AN-80i unit. This key (string of numbers, letters, and

dashes) must be entered into AN-80i configuration to allow full operation of the wireless

link.

3. Record the MAC address for each system to be tested/installed (label on AN-80i units).

The MAC address is needed to identify each AN-80i and select the correct Options Key

to be entered.

4. One or two PCs each having an Ethernet interface port, Web browser software installed

(Internet Explorer recommended), and a CAT-5 cross-over Ethernet cable for each PC.

5. A location with adequate space and power facilities.

6. To satisfy FCC and IC RF exposure requirements for RF transmitting devices, the

following distances should be maintained between the antenna of this device and

persons during device operation:

Table 1:FCC & IC RF Recommended Safe Separation Distances

Frequency (GHz) Mode Separation Distance

3.3 - 3.8 PTP / PMP 130 cm (52 in) or more

4.9 - 5.3 PTP / PMP 255 cm (101 in) or more

5.4 PTP / PMP 40 cm (16 in) or more

5.8 PMP 20 cm (8 in) or more

PTP 310 cm (122 in) or more

7. Redline does not endorse testing indoors with antennas. The operation of antennas in

close proximity results in poor connectivity due to high RF multipath effect and RF

saturation may damage equipment. Indoor testing may require the use of an RF

chamber.

When performing indoor testing the RF outputs from each AN-80i can be connected

together through a static/variable attenuator. Refer to the connection diagrams on the

following page.

4.2 Required Test Equipment

1. PC#1: Use a crossover CAT-5 Ethernet cable to connect PC#1 to the PoE Data In port

on the AN-80i. Equipped with a Web browser (requires Internet Explorer 6.0 or higher),

and Ethernet port for connection to AN-80i (PTP Slave). The IP address/subnet mask

must be set for the same subnet as the AN-80i. Recommended IP settings are:

IP address = 192.168.25.22, Net Mask = 255.255.255.0

2. PC#2: Use a crossover CAT-5 Ethernet cable to connect PC#2 to the PoE Data In port

on the AN-80i. Equipped with a Web browser and Ethernet port for connection to AN-80i

(PTP Master). The IP address/subnet mask must be set for the same subnet as the AN-

80i. Recommended IP settings are:

IP address = 192.168.25.23, Net Mask = 255.255.255.0

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

Figure 1: AN-80i Indoor Test Connection Diagram

Figure 2: AN-80i Outdoor Test Connection Diagram

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

5 Assemble and Configure AN-80i

Unpack the AN-80i and connect all components according to the Quick Test wiring

diagrams on page 3. Do not power-on the AN-80i unit at this time.

PoE Caution -- Warning to Service Personnel: 48 VDC

Customer equipment including personal computers, routers, etc., must be connected

only to the INPUT (DATA) port on the PoE unit. Only the outdoors Ethernet interface

cable connecting to the AN-80i can be safely connected to the OUTPUT (DATA &

POWER) connector. Connecting customer premises Ethernet equipment directly to

the OUTPUT (DATA & POWER) connector on the Power-over-Ethernet power

adapter may damage customer equipment.

6 Configure AN-80i Systems

1. Enter the AN-80i Options Key

a) Use an Ethernet cable to connect the PC #1 (192.168.25.22) to the INPUT port of

the PoE power adapter.

b) Power-on the AN-80i by connecting AC power to the PoE power adapter.

c) On the PC, open a browser and enter the default IP address (192.168.25.2). Login to

the AN-80i using the factory defaults:

Username: admin

Password: admin

d) Click Product Options in the left hand menu of the Web screen and enter the options

key for the this AN-80i unit. Every options key is unique to the MAC address of an

AN-80i and keys cannot be reused. Option keys are provided by your local Redline

equipment supplier. The options key enables AN-80i features including the maximum

Uncoded Burst Rate (UBR) and frequency ranges (region codes). Without the

options key, only very limited operation is possible (restricted power, UBR, and

frequency selection).

Figure 3: Configuration - Options Key

Important: If an AN-80i is placed in-service without first

entering a purchased permanent Options Key -- the

wireless link will experience a service outage.

2. Configure the AN-80i

For each link, one AN-80i unit must be designated as 'PTP Master' and the second unit

as 'PTP Slave'. When powered-on, the PTP Master will actively transmit to establish a

link with the (passive) PTP Slave.

Click Configure System in the left hand menu of the Web screen and make the

recommended settings for each AN-80i. It is recommended to first configure the PTP

Slave.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

Table 2: Web -Recommended Settings

Setting PTP Slave PTP Master

IP Address 192.168.25.2 192.168.25.3

RF Freq. (MHz) Must match Master RF

setting

Set RF according to

network design

ATPC Enable (Disabled) (Disabled)

Adaptive Modulation (Enabled) (Enabled)

System Mode PTP Slave PTP Master

Encryption Type None None

Link Length Measurement Mode Automatic Automatic

Radio Enable (Enabled) (Enabled)

After making these settings, click Save at the bottom of the configuration screen. If the

IP address was changed, you must change the address entered in the Web browser to

match the new AN-80i IP address.

Repeat steps 1 & 2 to configure the PTP Master AN-80i using the second test PC

(192.168.25.23) if available. If only one PC is used, move the PC#1 Ethernet connection

to the second PoE power adapter.

3. Test the Wireless Connection

The AN-80i units should now be operating on the same RF channel and will

automatically negotiate a wireless connection. Use the following steps to verify

connectivity:

a) From PC #2, enter the IP address of the PTP Slave AN-80i (192.168.25.2) into the

Web browser and login to the AN-80i unit.

b) On PC #2, open a command line window and use the following command to send a

ping message to PC#1 (192.168.25.22) over the wireless interface.

ping 192.168.25.22

You should observe a result similar to the following:

Reply from 192.168.25.22: bytes=32 time=1ms TTL=63

7 Field Installation Instructions

These steps should be performed after successfully completing the pre-installation tests

and configuration.

Install AN-80i

Install the AN-80i, mounting bracket, and antenna. The maximum length of the Ethernet

cable is 100 m (328 ft). For example, 98 m from the AN-80i to the PoE, and then 2 m

from the PoE to the network equipment connection.

Important: Ethernet Plug Must 'Click' into Socket

When inserting the RJ-45 plug, you should hear an audible 'click

' from the

plastic locking mechanism. Ensure the connector is locked before sealing and

weatherproofing the AN-80i. Do not use cables where this locking mechanism is

broken or has been removed!

Always follow local and national electrical and building codes for grounding and safety. If

you have determined that it is appropriate to install lightning protection for your system,

refer to the AN-80i Installation Guidelines manual for additional information.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

8 Mounting Brackets

8.1 Heavy-Duty Mounting Option

Figure 4: AN-80i with 80i-HD-MNT Mounting Kit

8.2 Lightweight Mounting Option

Figure 5: AN-80i with 80i-LD-MNT Mounting

8.3 Stand-Alone Mounting Option

Figure 6: AN-80i with 80i-SA-MNT Mounting Kit

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

AN-80i Installation Guidelines

1. Verify Free Channel (Spectrum Sweep)

It is recommended to check that the planned RF channel is available at the deployment

site. A spectrum sweep must be performed from both ends of the link. When performing

a sweep from the PTP Slave, the PTP Master must be powered-off or have the

transmitter disabled. The PTP Slave will remain passive during a spectrum sweep from

the PTP Master.

a) Login to the AN-80i Web interface and click Spectrum Sweep in the left hand menu.

b) Enter the Start Frequency, End Frequency, and Step (multiple of 2.5 MHz) for the

spectrum to be scanned. Set the No of Acquisitions to '10' and click the Start button

to begin the scan.

c) After reviewing the results, enter a narrower frequency scan and higher sample value

to monitor a potentially clear channel.

d) Repeat the spectrum sweep from the remote-end AN-80i.

Note: It is also recommended to use the Redline RF Monitoring Tool. This PC-based

application continuously polls both ends of a wireless link and graphs the RSSI and

SINADR values in real time. Contact your Redline sales representative to obtain this

useful deployment and troubleshooting tool.

2. Align Antennas

a) Align each antenna in azimuth and elevation plane. Verify that RSSI values at the

base station and subscriber match your link budget predictions. If the RSSI is not

within 5 dB of the expected value, recheck the antenna alignment and ensure there

are no obstructions in the RF path. Record RSSI/CINR as reference values.

b) If desired, you can enable the antenna alignment buzzer. This feature provides an

audible signal of the received signal strength (stronger signal->faster repetitions).

Click Configure System in the left hand menu of the Web screen and make the

following setting:

Antenna Alignment Buzzer Enable: (Enabled)

The buzzer remains active until disabled by the operator.

3. Connect AN-80i to the Network

Make all necessary changes to the AN-80i subscriber station configuration before

connecting to the network. Use a CAT-5 Ethernet cable to connect the data network to

the Data In port on the PoE power adapter. Refer to the AN-80i User Manual and AN-80i

Installation Guidelines manual for further details.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Otros manuales para RedCONNEX AN-80i

Tabla de contenidos

Otros manuales de Módulo inalámbrico de Redline Communications

Redline Communications

Redline Communications RDL-3000 Family Manual de usuario

Manuales populares de Módulo inalámbrico de otras marcas

Laird

Laird RM024 Manual de usuario

Laird

Laird BT830-SA Guía de configuración rápida

Ebyte

Ebyte E49-400T20S Manual de usuario

Fibocom

Fibocom FM101-NA-20 Instrucciones de instalación

Waldmann

Waldmann EnOcean TALK MODUL G2 Manual de usuario

Smartech

Smartech LBT-1.DO4 Manual de usuario

Cooper Wiring Devices

Cooper Wiring Devices ESPIRE RF RFAPM Manual de usuario

Yuga

Yuga CLM920 Manual de usuario

Waldmann

Waldmann TALK Bluetooth Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions UC864-G Manual de instalación

Ebyte

Ebyte E07-900M10S Manual de usuario

Quectel

Quectel SC690A Series Suplemento

Panasonic

Panasonic INDUSTRY PAN9028 Guía de configuración rápida

Ebyte

Ebyte E70-433NW30S Manual de usuario

LongSung Technology

LongSung Technology U9507E Manual de usuario

Wistron NeWeb

Wistron NeWeb DNUR-S2 Manual de usuario

Ebyte

Ebyte E49-400M20S4 Manual de usuario

RF-Star

RF-Star SimpleLink RF-BM-2652P1 CC2652P Manual de usuario