Redback A 4031B Manual de usuario
Operating Manual
A 4031B 30 Watt Public Address Amplifier
A 4033B 30 Watt Public Address Amplifier Rack Mount
Redback®Proudly Made In Australia
IMPORTANT NOTE:
Please read these instructions carefully from front to back prior to installation. They include important setup instructions.
Failure to follow these instructions may prevent the system from working as designed.
®
A 4031B
A 4033B
2Redback®Proudly Made In Australia
FEATURES
• 3 Inputs suitable for either microphone or line level, or for use as microphone and line level coupled together. disc, cassette, tuner, etc.
• Bass and treble controls (on both microphone and auxiliary inputs).
• Full 30W RMS output (100V and 4 -16Ωoutputs).
• Push to talk muting.
• Protection against over-voltage, over current, thermal run-away and short circuit load.
• Internationally accepted IEC mains socket (240V AC operation only).
• Stereo RCA sockets for all auxiliary inputs (configured to mono internally allowing standard stereo equipment to be directly connected).
• Fully balanced microphone inputs.
• Tape output, suitable for recording, or for connection to a second amplifier.
• Ten year warranty.
CONNECTIONS
Microphone 1
There are three types of sockets on the rear of the amplifier for microphone one. These are 6.35 mm (unbalanced) jack, 5 pin din, or 3 pin XLR
female. The 5 pin din has facility for PTT (push to talk) muting. The PTT contacts will mute input 2 (mic 2 and aux 2) and input 3 (mic 3 and
aux 3). The PTT contacts will not mute Aux 1 input. Wiring for 5 pin din socket is as per Fig 1. We recommend that you connect only one
microphone at a time to input 1.
For connection to the 3 pin XLR sockets refer to Fig 2.
Microphones 2 and 3
These are via 3 pin XLR sockets. Refer to Fig 2 for wiring these.
Speaker Outputs
Screw terminals are provided for both VC (voice coil) and 100V outputs. Minimum impedance for 100V loads is 333Ω(When only the 100V
output is used).Minimum impedance when only VC output is used is 8-16Ω@ 30W total load. A combination of 100V and VC is possible how-
ever we do not recommend this. If more than 30W is used then the unit may shut down due to overloading.
Tape Out
This is a mono output configured for a stereo lead for direct connection to a stereo source. This is suitable for connection to an auxiliary input
on external equipment. This is also suitable for driving 600Ωloads.
JP1 JP2
Configuration 1
When both jumpers are set to the outside the following logic applies...
•When paging through input 1, the VOX switch (where fitted) mutes
both inputs 2 and 3.
•When the PTT contacts on input 1 are closed, both inputs 2 and 3
are muted.
•Paging through input 2 or input 3 has no effect on any other input.
Note
1-There is no PTT facility on inputs 2 and 3.
2 - The PTT facility on microphone 1 will not mute Aux.1.
Configuration 2
When both jumpers are set to the inside the following logic applies...
• When paging through input 2, the VOX switch mutes input 3.
• When the PTT contacts on input 1 are closed, input 3 is muted.
• Paging through input 3 has no effect on any other input.
Note
1 - There is no PTT facility on inputs 2 and 3.
2 - There is no priority between input 1 and input 2 in this
configuration, i.e. paging on both inputs 1 and 2 simultaneously will
mean they mix together.
INTERNAL JUMPER SETTINGS
The amplifier has 3 sets of internally selectable jumpers, located as per figure 3.
VOX Muting Adjustments
VOX can be selected ON or OFF on the board via JP3.
1-VR1 adjusts the VOX sensitivity (i.e. input level that will activate switch). Turning the trimpot anticlockwise (as viewed from top) will make the
VOX switch less sensitive. This will prevent unwanted activation due to high ambient (background noise).
2 - VR2 adjusts the tail length (i.e. time before switching off) of the VOX switch. Turning VR2 anti-clockwise will increase the tail length.
Important Note: There are only two combinations of jumper settings for JP1 and JP2:
• Configuration 1: both jumpers set to the outside
• Configuration 2: both jumpers set to the inside
No other combinations can be used.
JP1 JP2
3
Redback®Proudly Made In Australia
Figure 1 - Inside top view of amplifier, showing the location VOX adjustments.
OPERATION
Once all inputs and outputs are connected:
1 - Turn bass and treble to midway point.
2 - Turn all volume controls to zero.
3 - Turn power switch on. Power indicator should illuminate.
4-Turn on microphone or auxiliary input source and adjust appropriate volume control to desired level.
The microphone and auxiliary for each input are mixed together, e.g. mic 1 and aux 1 are mixed. Both the mic and auxiliary inputs can be run
together but note there is only the one volume control for both of these.
TROUBLESHOOTING
No Power
(Power LED light does not illuminate)
Check mains fuse. Only replace with M205, 240V AC 0.5A rated fuse.
Distorted output
Check that the speaker type is correct for the output that you are using. Check for any short circuits on the speaker line.
Very low output
Make sure that the input is the correct level (check for shorted connectors). Check for any short circuits on the speaker line.
Continually blows fuses
Make sure that the speaker line is not shorted. Check also speaker types, ratings and if on correct output.
Amplifier keeps cutting in and out
Make sure that there is adequate ventilation around the amplifier. Check the vent slots on the case are not covered or blocked. Check also
speaker types, ratings and for any short circuits on the speaker line.
4Redback®Proudly Made In Australia
BALANCED
AUDIO
PTT
Figure 2 - 5 Pin din socket
wiring diagram. As viewed
from the rear of the amplifier.
From Microphone
Input
Unbalanced
1
2
3
Signal
Shield
XLR Mic
Input
From Microphone
Input
Balanced
Shield
XLR Mic
Input
Signal
12
3
Figure 3 - Microphone Connections
Connector Type:........................................................XLR 3Pin Female
Pin 1: .........................................................................................Earth
Pin 2: ....................................................................Signal Inphase (hot)
Pin 3: ...........................................................Signal Out of Phase (cold)
FOR P.T.T. (Push To Talk) paging use the 5 pin din input on mic 1
1
4
3
5
2
SPECIFICATIONS
POWER OUTPUT: 30 Watts RMS
T.H.D.: typically < 0.5% @ 1kHz
FREQUENCY RESPONSE
Microphone: 52Hz - 10kHz, ±3dB
Auxiliary: 40Hz - 10kHz, ±3dB
SPEAKER OUTPUTS: 100V (330Ω) (floating)
or 8 - 16Ω(0V referenced)
NOISE LEVEL: All volume controls min:
typically 76dB below rated output
(All inputs display same signal to noise ratio)
OUTPUT CONNECTORS
Speakers: Screw Terminals
Tape Output: RCA Stereo Socket
INPUT SENSITIVITY
Mic 1: 2.6mV Balanced
or 3.2mV Unbalanced
Mic 2: 2.6mV Balanced
Mic 3: 2.6mV Balanced
Aux 1: 150mV
Aux 2: 150mV
Aux 3: 150mV
MUTING: PTT Via Microphone
Switch Contacts
or Optional VOX Muting
-79dB below rated output
INPUT CONNECTORS
Mic 1: 5 pin DIN balanced
or 3 pin XLR balanced
or 6.35mm jack unbalanced
Mic 2: 3 pin XLR balanced
Mic 3: 3 pin XLR balanced
Aux 1: RCA Stereo Socket
Aux 2: RCA Stereo Socket
Aux 3: RCA Stereo Socket
240V AC Power: IEC Type Chassis Socket
CONTROLS
Input 1 (Mic 1 / Aux 1): Volume
Input 2 (Mic 2 / Aux 2): Volume
Input 3 (Mic 3 / Aux 3): Volume
Bass: ±10dB @ 100Hz
Treble: ±13dB @ 10kHz
Power: On/Off Switch
POWER SUPPLY 240V AC
INDICATORS: Power on LED
PROTECTION: AC Fuse 0.5A
DC Fuse 2 x 3A
DIMENSIONS
A 4031B: ≈300W x 220D x 80H mm
A 4033B: ≈483W x 220D x 88H mm
WEIGHT:
A 4031B: ≈4.1kg
A 4033B: ≈5.1kg
ACCESSORIES IEC Mains Lead
* Specifications Subject to Change Without Notice
Este manual sirve para los siguientes modelos
1
Otros manuales de Amplificador de Redback
Redback
Redback A 4031C Manual de usuario
Redback
Redback A 4387A Manual de usuario
Redback
Redback A4260B Manual de usuario
Redback
Redback A 4235A Manual de usuario
Redback
Redback A 4116 Manual de usuario
Redback
Redback A 4210 Manual de usuario
Redback
Redback A 4262B Manual de usuario
Redback
Redback Phase 5 A 4390A Manual de usuario
Redback
Redback A 4024 Manual de usuario
Redback
Redback A 5122 Manual de usuario
Redback
Redback A 4260A Manual de usuario
Redback
Redback A 4020B Manual de usuario
Redback
Redback A 4017 Manual de usuario
Redback
Redback A4260 Manual de usuario
Redback
Redback A 4312 Manual de usuario
Redback
Redback A 4310 Manual de usuario
Redback
Redback A 2082 Manual de usuario
Redback
Redback PHASE 5 A 4395A Manual de usuario
Redback
Redback A 1937 Manual de usuario
Redback
Redback A 1116 Manual de usuario
