Raymarine ST50 plus Manual de instrucciones

Distributed by

Any reference to Raytheon or

RTN in this manual should be

interpreted as Raymarine.

The names Raytheon and RTN

are owned by the

Raytheon Company.

Nautech Limited, Anchorage Park, Portsmouth

PO3

5TD.

England

Telephone (0705) 69361 I. Fax (0705) 694642

DEPTH

Operation and

Installation

ST50

Plus

Depth

Operation and Installation Handbook

Autohelm and SeaTalk are registered Trade Marks of Nautech Limited

Autohelms policy of continuous improvement and updating ma); change product specifications without

prior notice

ST50

plus Depth Operation and Installation Handbook

Package Contents

The following items are included in the ST50 Plus Depth package:

1. ST50 Pius Depth control head

Fixing studs (2 offI

Thumb nuts (2 oftI

4. Fitting template

5. Power cable

Depth transducer (through

hull)

with

14m(45ftI

of cable

7. Control head cover

Operation and Installation handbook

Worldwide

Setice

Cenb-e handbook

10. Warranty document

11.

Security code sticker

ST50

plus Depth Operation and Installation Handbook

DEP,”

-1

ST50

Plus Depth Operation and Installation Handbook

Contents

Introduction

.........................................................................

Chapter 1: Control Head Installation

.........................................

1.1

Sing

............................................................................

1.2 Mounting Procedure

........................................................

1.3 Power Supply (stanchalone operation)

..................................

1.4 Power Supply (SeaTalk operation)

.....................

;‘.

............... f

1.5 Connection of Separated Instruments

.................................

;

1.6 Ring Connection

............................................................. I

1.7 Connection to SeaTalk Compatible Autopilots

........................ I

Chapter 2: Transducer Installation

.......................................... .

2.1 Connection to the Control Head

.......................................... -

2.2 Transducer Selection

......................................................

2.3Transducer

Installation c

....................................................

Chapter 3: Fault Finding and Maintenance

.............................

3.1 FaultFinding

............................................................... .13

3.2 Maintenance

............................................................... 14

Chapter 4: Operation

..........................................................

4.1

DepthKey

..................................................................

.16

4.2AarmKey .................................................................... 18

4.3

Dffset Key

...................................................................

4.4

Reset Key

................................................................... 21

4.5 Display Contrast

...........................................................

Chapter 5: CODE Lock Security

.............................................

Chapter

Calibration

........................................................

6.1

initial Calibration

............................................................

6.2 Intermediate Calibration

.................................................

6.3 Extended Calibration

......................................................

Chapter 7: General Specification

..........................................

ST50

Plus Depth Operation and Installation Handbook

ST50

plus Depth Operation and Installation Handbook

Intmduction

The ST50 Plus Depth is a SeaTalk compatible, multifunction instrument that

employs a powerful echo sounder to give excellent performance over a wide

range of sea conditions.

Deep, shallow, anchor watch alarms can be set to provide visual and audible

warnings when the water depth reaches selected thresholds.

The ST50 Plus Depth can be configured to operate as a master unit or a

dedicated repeater.

settings are stored in permanent memory and

retained even when the power source is disconnected.

The ST50 Plus Depth also incorporates a securii feature to protect

instruments mounted in vulnerable areas such as the cockpit, helm or mast.

Thank you for purchasing an Autohelm product May we take this opportunity

towishyouyearsoftroublefreeoperation.

‘

ST!50

Plus Depth Operation and htaliation

Handbook Chapter 1: Confrol Head Installation

Chapter

Coniroi

i-&j

ins&&h

llOmm(4.33in)

38 .75mm

(1.5in)

1.1

Sing

The ST50 Plus Depth is designed for above or below deck installafion

where it is:



Easily readable by the helmsman



Protected against physical damage



At least 230mm (gin) from a compass



At least

5&m

(20in) from radio receiving equipment



Accessible from behind for ease of installation and cable running

Caution:

To prevent moisture forming on the display window, the ST50 Plus

Depth ‘breathes’ through a small vent in the cable boss.

Ihere-

fore, the control head must be sited where the rear case is

protected from contact with water.

_.-.-

___^_

__._

_...

.._-

._.-

____,_.-

-- -

,’

ST!%

plus Depth Operation and Installation Handbook

Cable boss 2 Fiiing studs

3lhumb

nuts

4Gashet

1.2 Mounting Procedure

Make sure that the selected location is

clean,

smooth and flat.

Apply the self-adhesive template (supplied) to the selected location and

mark the centres for the fHing studs (2) and the cable boss

(1).

Drii two 4mm

(5/32in)

clearance holes for the fixing studs

(2)

through

the bulkhead. Remove the template.

Cut the clearance hole for the cable boss

(1)

using a 50mm (2in)

diameter cutter.

5. Screw the two fixing studs

(2)

into the control head.

Pass the SeaTalk cable and transducer tails through the cable-boss (1)

clearance hole.

7. Assemble the contiol head to

tie

bulkhead and secure from behind

using the thumb nuts

(3).

Note:

The rear case is fitted with a foam gasket to form a water-tight seal between

the instrument and the selected installation face. Under no circumstances

must silicone greases be applied to this gasket as an additional method of

sealing-the silicone will expand and distort the

rear case.

ChaMer 1: Control Head Installation

Bracket Mounting

The ST50 Plus Depth can, as an alternative, be bracket mounted using the

Autohelm Mounting Kit.

Flush Mounting

A flush mounting kii is available for installations where a flush mount is

required or more desirable. Full installation instructions are provided with

the kit.

---

e--m._

--._-___

’

ST50 Plus Depth Operation and ImtaUation Handbook Chapter I: Control Head Installation

1.3 Power Supply (stand-alone operation)

Connect

the 2m (6ft.l power supply cable directly to the distribution

2. Cut the cable to length and connect the red wire to the

+12V

terminal

and screen to the OV terminal.

3. Cut back and insulate the yellow wire.

4. Protectthe

circuiiwith a SAcircuiibreaker.

Longer runs to the power supply can be made using the

(3OftI SeaTalk

Extension Cable

D131).

1.4 Power Supply (SeaTalk operation)

All instmrnents in a SeaTalk system receive power and information from the

SeaTalk bus. Each instrument has two SeaTalk connectors

pin) on

15Omm (6in) tails. To supply power and information to the instrument simply

plug adjacent tails into the ST50 Plus Depth tails.

”

:s.

To transducer

,::

::.

1,.

.l’.,

SeaTalk tails SeaTalk

tails

D,,,.

1.5 Connection of Separated lnsttuments

Separated instruments can be connected using one of the range of SeaTalk

Extension Cables. These cables are supplied with a SeaTalk

connecMitted

to each end. Ajunction boxcan be used tojointhecableifitis cutforeasier

routing or shortening.

If preferred, any 2 core, screened cable conforming the following specifiMion

may be used instead of the SeaTalk cable.



AWG, 2 core screened cable with a minimum copper area of 0.5mmz.

Junction

box

rYeUowl

Screen J

LRed J

8 \

ST50 Plus Depth Operation and Installation Handbook

1.6 Ring Connection

Chapter 2: Transducer Installation

Installations with large numbers of instruments on a SeaTalk bus may require

a second ringmain connection to the power supply breaker to prevent

excessive voltage drops. Refer to the foflowing list to determine whether a

second ring main is necessary.

Cable run upto 10m (3%)

Single connection: 13 instruments maximum

Second connection: 26 instruments maximum

Cable run

upto

20m (66ft)

Single connection: 7 instruments maximum

Second connection: 13 instruments maximum

The second ringmain should be connected to the spare lead on the last

instrument in the chain and directed back to the circuit breaker.

2.1 Connection to the Control Head

The depth transducer is supplied, as standard, with a through hull

fling

and

14m

(45ftI

of cable. The cable is equipped with a SeaTalk connector that

plugs into a control head connector.

1.7 Connection to SeaTalk Compatible Autopilots

If the installation includes a SeaTalk compatible Autopilot the

ST50

instru

ments may be connected to the SeaTalk bus at any point. No independent

connection to the 12V power supply is necessary as the instruments receive

power from the Autopilot course computer.

To autopilot

SeaTalk BUS

Connection

To any further

ST50 Instruments

or Autopilot

Control Units “,,u-

Chapter 2: Transducer

installation

2.2 Transducer Selection

The type of depth transducer used is governed by the hull material. The

following list shows the appropriate transducer for hull type.

Transducer Type Hull Material

ZO91 Through Hull Plastic: GRP (Glass Reinforced

Plastic),

Steel and

Aluminium

Z118

Through Hull Bronze:

2120 Retractable througb

hull:

Wocd

GRP (Glass Reinforced Plastic), Steel and

Aluminium

2.3 Transducer Installation

All

depth transducers are supplied with detailed installation and maintenance

instructions.

These instructions, together with the following notes, should be read

thoroughly before attempting to install the transducer.

Tabla de contenidos

Otros manuales de Transductor de Raymarine

Raymarine

Raymarine RV-100 RealVision 3D Manual de usuario

Raymarine

Raymarine HYPERVISION HV-100 Manual de usuario

Raymarine

Raymarine REALVISION 3D RV-3 Series Manual de usuario

Raymarine

Raymarine RV2 Series Manual de usuario

Raymarine

Raymarine DownVision CPT-70 Manual de usuario

Raymarine

Raymarine REALVISION 3D Manual de usuario

Raymarine

Raymarine HYPERVISIONT HV-300 Series Manual de usuario

Raymarine

Raymarine HYPERVISION HV-100 Manual de usuario

Raymarine

Raymarine RVM-100 Manual de usuario

Raymarine

Raymarine HYPERVISION HV-300 Manual de usuario

Raymarine

Raymarine RV-100 RealVision 3D Manual de usuario

Raymarine

Raymarine RV-300 Series Manual de usuario

Raymarine

Raymarine DownVision CPT-70 Manual de usuario

Raymarine

Raymarine RSW-Wired Manual de usuario

Raymarine

Raymarine Wind Vane Manual de usuario

Raymarine

Raymarine Realvision RV-220P Manual de usuario

Raymarine

Raymarine RVM-400 Series Manual de usuario

Raymarine

Raymarine Transducers Manual de usuario

Raymarine

Raymarine RV-100 RealVision 3D Manual de usuario

Manuales populares de Transductor de otras marcas

HBM

HBM AD101B Manual de usuario

Camille Bauer

Camille Bauer SINEAX F534 Manual de usuario

Trane

Trane KIT 16724 Instrucciones de montaje

Lumel

Lumel P18 Manual de usuario

B&C Speakers

B&C Speakers DE75PTN Manual de usuario

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Manual

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Manual de usuario

ProMinent

ProMinent Dulcometer DMT Manual de usuario

MKS

MKS MicroPirani 925 Series Cómo utilizar

WIKA

WIKA WU-20 Manual de usuario

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Manual de usuario

Camille Bauer

Camille Bauer SIRAX CH-5610 Manual de usuario

WIKA

WIKA F2802 Manual de usuario

Veris Industries

Veris Industries PW Series Manual de usuario

HBM

HBM TJ1-S6 Manual de usuario

Simrad

Simrad ES120-7C - REV D Guía del usuario

HBM

HBM C18 Manual de usuario

Airmar

Airmar M260 Manual de instrucciones