Raymarine mn100 Manual de usuario
Digital Display
Important
Due to the wireless communication systems used in Micronet
instruments they are only recommended for use on boats up to 18 metres
(60 ft.) Before installing to a boat of aluminium or steel construction,
please contact your Raymarine dealer.
Like any other electronic instruments your Micronet system is designed
to serve only as an aid to navigation and it remains the skippers
responsibility to maintain a permanent watch and be aware of developing
situations.
EMC Conformance
All Raymarine equipment is designed to the best industry standards for
use in the recreational marine environment. The design and
manufacture of Raymarine equipment conforms to the appropriate
Electromagnetic Compatibility (EMC) standards. Correct installation is
required to ensure that performance is not compromised.
mn100 Digital Display
www.raymarine.com
1 Information Page
1.1 Introduction - 2
1.2 Specifications - 2
1.3 Power Management and Battery Life - 2
1.4 Safety and Disposal - 4
2 Operation
2.1 Display Information - 5
2.2 Switching the System On and Off - 5
2.3 Backlighting - 6
2.4 Audible Signals and Alarms - 6
2.5 Utilities - 8
2.6 Chapter and Page Operation - 9
2.7 Chapter and Page Description - 11
3 Setup and Calibration
3.1 Entering Setup and Calibration Mode - 18
3.2 Chapter and Page Setup and Calibration - 18
3.3 Editing Values - 18
3.4 Setup Page Description - 20
3.5 Calibration Page Description - 23
4 Seatrial and Calibration
4.1 Depth Offset - 29
4.2 Speed Calibration - 30
4.3 Wind Calibration - 31
4.4 Compass Calibration and Alignment - 32
5 Installation
5.1 Tools List & Parts - 33
5.2 Precautions and Positioning Advise - 33
5.3 Bracket Mounting - 34
5.4 Surface Mounting - 35
5.5 External Power Connections - 36
6 Maintenance and Fault Finding
6.1 Care and Maintenance - 37
6.2 Fault Finding and Technical Support - 37
7 Warranty Information
Contents
1
www.raymarine.com
1 Information
1.1 Introduction
Your Micronet display is powered for life by the environment. Although
feature packed and highly visible in all conditions, current demand is so
low, and the supply so efficient, that the solar-powered display is self
sufficient. Combined with other displays in the Micronet range this
display becomes part of a complete navigational system.
1.2 Specifications
Height of digits: 38mm (1.5")
Backlighting: 3 levels with daylight shutoff
System-wide or local control
Power: Solar Powered
300 hrs autonomy by day, 7 nights at brightest backlighting,
20 nights at economy backlighting without charge
Units of display: Boat Speed (knots, km per hour, statute miles per hour)
Distance (nautical miles, statute miles, kilometres)
Depth (metres, feet, fathoms)
Wind Speed (knots, metres per second, Beaufort)
Alarm: Audible Alarm for Depth, Wind
Weight: 285g (0.63lbs)
Operating Temp.: -10oto +60oC (14oto 140oF)
Frequency: 868 MHz or 916 MHz
This unit can be controlled using the T113 Remote Display
1.3 Power Management and Battery Life
What makes your mn100 display possible is Raymarine’s revolutionary
approach to power management. By reducing the amount of power
being used by the electronics and maximizing the potential of the sun to
provide power, a mn100 display becomes a virtually perpetual device.
Power status is indicated by two icons on the display:
Battery Level and Charge Rate
Used together these icons will show the condition of the power supply.
mn100 Digital Display
2www.raymarine.com
Information
3
If using the displays at night, power usage can be reduced dramatically
by switching the Backlighting to level 1 or Off. If Backlighting is not
required on displays located below decks it is best to set them to "Local"
Backlighting control (see page 26 -s35) so that power is not being
wasted in displays which may not be visible from the one being viewed.
If the internal battery is fully charged then it does not matter how
much the display is subjected to bright sunlight no further charging
is required and the Charge Rate Indicator will remain low.
If the displays are to be stored for a long period of time before next
use (Over Winter) ensure that the batteries are fully charged before
storage. If necessary connect to a 9 to 30V DC power supply for 24
hrs prior to storage, using the external power leads.
www.raymarine.com
Bright Sunny Day
Overcast Day
Night
Battery is charged and being
topped up by the sun. (see Note)
Battery is low and being charged
by the sun.
Battery is charged and requires no
further charging.
Battery is low but maintaining it’s
level.
Battery is charged but is not
charging.
Battery is low with no charging.
It is recommended that the
instrument be left in daylight for
some time for the battery to
recover, or charge from an external
9-30V power source. A fully
discharged battery will recharge in
approximately 12 hours of direct
bright sunlight.
LOW Power
Sleep Mode
If there is no boat speed or change in heading registered on the system
for a period of 12 hours your Micronet display will switch off to conserve
power. A "POWER SAVE" alarm will sound before the system switches
off. Pressing any button within 10 seconds of the alarm sounding will
allow the system to remain switched on.
Backlighting will automatically shut down/off when operated in daylight.
AArrttiiffiicciiaalllliigghhttWWIILLLLNNOOTTrreecchhaarrggeetthheebbaatttteerryy. Placing your Micronet
display close to an artificial light will seriously damage the display.
Only recharge in natural daylight.
Applying External Power
In cases where displays are mounted permanently below decks it will be
necessary to apply an external power source to prevent complete
discharge of the built in battery.
Connections on the rear of the display allow a 9V to 30V DC power
source to be connected. Connections can be made to the vessels DC
system or to a 9V battery pack. It is recommended that permanent
connection is only made when the displays are permanently fixed to the
vessel and not when the clip brackets are used.
Connection to a 9V (PP3) battery will fully recharge the internal battery
over a period of 24 hours.
1.4 Safety and Disposal
Your Micronet display contains Manganese Lithium Dioxide batteries
which should be disposed of correctly. Do not dispose of any instrument
in domestic waste. Refer to regulations in force in your country.
If in doubt return the instrument to Raymarine Ltd. for correct disposal.
mn100 Digital Display
4www.raymarine.com
2 Operation
Important:
Ensure that the "Auto Network" procedure described on the yellow
instruction sheet and full Setup and Calibration has been performed
correctly before attempting to use your Micronet system.
2.1 Display Information
2.2 Switching the System On and Off
To switch your Micronet system on or off select any display and press
the button for 2 seconds.
Operation
5
Chapter
Button
Hold
down for
on/off
Set-up
Button
Prompt
Alarm
Indicator
(Flashes)
Battery
Level
Set Button Page and Adjust Buttons
Hold down
for
Backlighting
Descriptive
Text
Charge
Rate
www.raymarine.com
Switch on Switch off
2.3 Backlighting
At any stage of the display’s operation press and hold for 2 seconds the
button to access the lighting control.
Pressing the and buttons will scroll through setting
OFF, 1, 2 and 3 whilst changing the backlighting.
Depending on the display setup (see page 26 –s35),
Backlighting on the whole system or just the single display
will be altered.
Backlighting is automatically switched off in daylight as part of the
display’s power saving feature and will not operate in daylight.
2.4 Audible Signals and Alarms
At stages during its operation your Micronet system will beep to indicate
alarms or moments of importance.
Power-up Once operating as part of a network the display will issue a single
beep as it is switched on by pressing the button for 2
seconds.
Button Press A single beep is issued each time a button is pressed. A second
beep is issued after a 2 second hold down of the button.
Timer A single beep will be issued at each minute of the countdown.
With 1 minute left to go a beep will sound every 10 seconds.
With 10 seconds to go a beep will sound every second.
Countdown complete will be indicated by a single burst of three
beeps.
Alarm Continuous bursts of three beeps will indicate an alarm.
The alarm activated will be indicated on the digital display,
accompanied by the flashing symbol.
Pressing any button will silence the alarm. See fault finding section
on p37.
Depth Shallow Alarm
The water depth has fallen below the preset alarm level.
The depth value that triggers the alarm is affected by any
keel or waterline offsets that have been added.
See page 22 s11
to set the alarm function.
This alarm does not sound as the depth increases above the preset
alarm level.
mn100 Digital Display
6www.raymarine.com
Operation
7
Depth Deep Alarm
The water depth has increased above or fallen below the
preset alarm level.
The depth value that triggers the alarm is affected by any
keel or waterline offsets that have been added.
See page 22 s12 to set the alarm function.
Wind High Alarm
The wind speed has increased beyond the preset alarm
level.
See page 22 s13 to set the alarm function.
This alarm does not sound as the wind speed decreases
below the preset alarm level.
Cross Track Error Large Alarm
A large cross track error has been alerted by the GPS.
See page 22 s14 to set the alarm function.
Waypoint Arrival Alarm
A waypoint arrival signal has been received from the GPS.
The waypoint name is shown on the top line of the display.
See page 23 s15 to set the alarm function
www.raymarine.com
mn100 Digital Display
8www.raymarine.com
2.5 Utilities
Keylock The Keylock feature protects from accidental key presses and is
intended for use in high activity applications such as crewed race
yachts. If your display is mounted in a position where keys may
be pressed accidentally (eg the companionway of a race yacht),
then you can enable keylock as follows:
Press and hold to enter set up
Press repeatedly to reach the OPTIONS chapter
Press repeatedly to reach the Key Lock page
Press to activate keylock
Press and hold to exit setup.
Once keylock is activated, pressing a key causes the unit to
give the unlock key prompt. Press followed by to
unlock the keys (this will allow the keys to function for one
minute, after which the keys will automatically relock).
Page Hiding To hide unwanted pages and configure an instrument to your
needs:
Press and hold to enter set up
Press to reach the OPTIONS chapter
Press to reach the Page Hiding page
Press to activate page hiding for 5 minutes
Press and hold to exit setup.
Once page hiding is activated:
Press for 2 seconds to hide a page.
A period of 5 minutes is allowed during which you can select
pages to hide.
Page Unhide To clear Page Hiding and return to all pages visible:
Press and hold to enter set up
Press to reach the OPTIONS chapter
Press to reach the Pages Hidden page
Press . to return to all pages visible
Press and hold to exit setup.
Otros manuales para mn100
1
Tabla de contenidos
Otros manuales de Monitor de Raymarine
Raymarine
Raymarine T210 Manual de usuario
Raymarine
Raymarine i70 Manual de usuario
Raymarine
Raymarine E-Series Manual de usuario
Raymarine
Raymarine St290 Manual de usuario
Raymarine
Raymarine ST40 Depth Instrument Guía del usuario
Raymarine
Raymarine i70 Manual de usuario
Raymarine
Raymarine ALPHA Manual de usuario
Raymarine
Raymarine gS Series Manual de usuario
Raymarine
Raymarine AXIOM XL 16 Manual de usuario
Raymarine
Raymarine gS Series Manual de usuario
Raymarine
Raymarine St290 Manual de usuario
Raymarine
Raymarine G170 Manual de usuario
Raymarine
Raymarine a9 Series Manual de usuario
Raymarine
Raymarine ST40 Guía del usuario
Raymarine
Raymarine A Series A50 Manual de usuario
Raymarine
Raymarine e7 Manual de usuario
Raymarine
Raymarine ALPHA Manual de usuario
Raymarine
Raymarine AXIOM+ Series Manual de usuario
Raymarine
Raymarine hsb2 PLUS Series Guía del usuario
Raymarine
Raymarine e7 Manual de usuario
