Raven CR7 Manual de usuario

User manual

CR7/CR12

QUICK START GUIDE

116-8000-017 REV. B2

| CR7/CR12 | QUICK START GUIDE

PAGE 2/35 | User manual |116-8000-017 |Rev. B2

DISCLAIMER | CR7/CR12 | QUICK START GUIDE

PAGE 3/35 | User manual |116-8000-017 |Rev. B2

DISCLAIMER

•The safety instructions contained in the manuals of the tractor or implements must be complied with at all

times.

•Always switch off the tractor before installing or repairing hydraulic and electrical components of the

SBGuidance system.

•It is strictly prohibited to use the CR7/CR12 system on public roads.

•It is strictly prohibited to leave a driving vehicle unattended when the CR7/CR12 system is switched on. The

driver is always responsible for the direction and course of the vehicle.

•To prevent injury or fire, replace defective fuses only with fuses of the same type and amperage.

•The SBGuidance the operating system is not able to detect and avoid obstacles. If there is an obstacle in your

path, you will always need to take action for it to be avoided.

•Only allow authorized/qualified persons to operate the system. Authorized/qualified persons are defined as:

persons who have read and understood the manual, have been given instructions by a product specialist, and

who are both physically and mentally fit and able to operate the system.

•The system contains moving parts! Make sure the immediate environment is clear of people before operating

the system.

•In case of system failure or breakdown switch of the tractor and disconnect the electrical power source to

avoid further damage. Contact your dealer for further instructions on how to repair your system.

•Always wear personal protective equipment when operating/adjusting/repairing the system outside of the

tractor cab.

•In order to prevent power surges from occurring, always start the machine first, before initiating the

SBGuidance control system.

•Only touch the touch-screen with your finger or by using a special touch-screen stylus/pen. Operating the

touch-screen with sharp objects may cause permanent damage to the screen.

•Always consult your supplier as to which products are best suited first before cleaning the touch-screen with

chemicals or alcohol.

•If the terminal is not used for a long period, better remove the terminal from the tractor and store in a heated

environment. This will extend the life span of the electronic components.

•To prevent theft, it is better to not let the terminal and GPS-antenna unattended in the tractor on the field.

WARNING!

PAY ATTENTION!

INDEX | CR7/CR12 | QUICK START GUIDE

PAGE 4/35 | User manual |116-8000-017 |Rev. B2

INDEX

DISCLAIMER.......................................................................................................................................................................................................3

INDEX...................................................................................................................................................................................................................4

1HOW TO CHANGE BETWEEN DIFFERENT TRACTORS ...............................................................................................................5

2COUPLING IMPLEMENT ........................................................................................................................................................................7

3DRIVE DIRECTION....................................................................................................................................................................................9

4NEW FIELD + CREATE NEW LINE....................................................................................................................................................10

5ADD SECOND LINE OR ADD MULTIPLE LINES ..........................................................................................................................13

6LOAD FIELD .............................................................................................................................................................................................14

7SWITCHING BETWEEN THE LINES..................................................................................................................................................17

8SHIFT THE POSITION OF THE LINE ................................................................................................................................................18

9NEW FIELD: RECORD FIELD BOUNDARY .....................................................................................................................................19

10 RECORD FIELD BOUNDERY...............................................................................................................................................................20

11 PRE-PLANNING OPERATION............................................................................................................................................................25

12 OPERATIONS ..........................................................................................................................................................................................27

13 EDIT REGIONS ........................................................................................................................................................................................30

14 NEW TASK + START OPERATION...................................................................................................................................................32

15 TASK + RELOAD OPERATION...........................................................................................................................................................33

16 EXAMPLE OF BUIDING A BOUNDERY...........................................................................................................................................34

HOW TO CHANGE BETWEEN DIFFERENT TRACTORS | CR7/CR12 | QUICK START GUIDE

PAGE 5/35 | User manual |116-8000-017 |Rev. B2

1HOW TO CHANGE BETWEEN DIFFERENT TRACTORS

Beschrijving

Afbeelding

If the tractor profile has to be changed.

Open the UT with the the UT widget.

Press the gear icon.

“Machine settings”.

Press the bar: change profile.

When you have selected the correct profile,

confirm the chosen profile by pressing the

checkmark. It is possible that the antenna

will be restarted. The UT can be closed by

pressing the green checkmark at the bottom

left.

HOW TO CHANGE BETWEEN DIFFERENT TRACTORS | CR7/CR12 | QUICK START GUIDE

PAGE 6/35 | User manual |116-8000-017 |Rev. B2

Press settings (the gear icon at the bottom

left), and then press Machine (the tractor

icon).

Press the configured tractor. A different type

of machine must also be loaded inside the

machine garage.

Select the correct tractor from the dropdown

menu.

SELECT IMPLEMENT | CR7/CR12 | QUICK START GUIDE

PAGE 7/35 | User manual |116-8000-017 |Rev. B2

2SELECT IMPLEMENT

Beschrijving

Afbeelding

Press settings (the gear icon at the bottom

left), and then press Machine (the tractor

icon).

Press the configured tractor. A different type

of machine must also be loaded inside the

machine garage.

There are two options, front and rear

mounted implements. An overview is

provided over the current mounted

implemts. To unmount a mounted machine:

Press the red cross behind the machine.

At the bottom of both sections is a button

“mount equipment”. Press it to mount the

equipment on the desired side. Multiple

implements can be mounted.

After pressing the mount equipment button

it is possible to switch between the already

created machines. Select the machine you

want and confirm with the green check mark

at the bottom right.

If a new machine needs to be created; press

"create new equipment"

SELECT IMPLEMENT | CR7/CR12 | QUICK START GUIDE

PAGE 8/35 | User manual |116-8000-017 |Rev. B2

Note:

Currently the “spreader” is mounted with a

working width of 16 meters devided in one

section. Working width is the distance that

will be created between the various

guidance lines. Press the green checkmark

finish the configuration.

An overview of the current selected tractor

and implement is provided.

Press the green check mark to confirm.

The machine has been configured, press the

green check mark again to return to the

main screen.

New lines (AB Lines):

Chapter 4

Loading field:

Chapter 6

New Field (create bounderies):

Chapter 10

DRIVE DIRECTION | CR7/CR12 | QUICK START GUIDE

PAGE 9/35 | User manual |116-8000-017 |Rev. B2

3DRIVE DIRECTION

Beschrijving

Afbeelding

It is possible that the direction is not

recognized correctly (forwards/backwards).

You can recognize it by the white arrow that

appears in the middle of the screen.

When driving forward and the white arrow is

visible (the system thinks you are driving

backwards) press as you drive forward on

the white arrow and it will disappear.

The white arrow is gone, the system knows

the correct direction of driving again.

Note:

NEW FIELD + CREATE NEW LINE | CR7/CR12 | QUICK START GUIDE

PAGE 10/35 | User manual |116-8000-017 |Rev. B2

4NEW FIELD + CREATE NEW LINE

Beschrijving

Afbeelding

Press on icon: “New field + New line”.

When the list of fields is open, first close it.

After this the icon will appear.

Enter a field name, task can also be renamed

(Field name + current date and time is the

default name).

Press to next page.

An overview of the tractor and attached

machine.

Press to next page.

If the machine configuration is not correct;

Reference back to Chapter 2.

Now we’ve created a new field. A new

guidance line can now be created by

pressing ‘’lines’’.

Otros manuales para CR7

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Raven

Raven

Raven SmarTrax Spra-Coupe 220 Manual de usuario

Raven

Raven AccuBoom Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven TC1 Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven AccuBoom Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven RS1 Manual de usuario

Raven

Raven AutoBoom Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven OMNiDRIVE Manual de usuario

Raven

Raven SBGuidance Auto Manual de usuario

Raven

Raven OmniRow Manual de usuario

Raven

Raven VSN Manual de usuario

Raven

Raven SC1 Manual de uso y cuidado

Raven

Raven SC1 Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven Hawkeye Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven Case IH Patriot 3XX0 Manual de usuario

Raven

Raven AutoBoom Case IH Patriot 250 Manual de usuario

Raven

Raven RS1 Manual de usuario

Raven

Raven SmarTrax Manual de usuario

Raven

Raven RS1 Manual de uso y cuidado

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario

TURF TANK

TURF TANK One+ Manual de usuario