Raven ENVIZIO PLUS Manual de usuario
ENVIZIO PLUS
Installation and Operation Manual
1
Congratulations on your purchase of the Envizio Plus guidance system!
This system is the ultimate guidance solution, featuring numerous guidance
patterns, LED combined with on-screen guidance, datalogging, and much
more.
Initial Start-up
Upon initial start-up of your Envizio Plus system, you will be prompted to
set two configuration settings. Once these two settings are made, the
Envizio Plus is ready for use. You will not be prompted again for these two
settings, only the very first time you power-on the system. After that, if you
wish to change these settings, you may do so via the Configuration Pages,
which you will learn about later in this manual.
Starting the Envizio Plus System
1. Press the Power switch to power-on the Envizio Plus system.
2. The first initial start-up screen, Swath Width, displays. Touch either the
‘10’ or the ‘1’ and then the right or the left red arrow to either
increase or decrease the swath width by increments of 10 or 1. After you
have set the desired number, touch ‘Next’.
2
3. The second initial start-up screen, Antenna Position, displays. Touch
either the ‘10’ or the ‘1’ and then the right or the left red arrow or the
up or down red arrow to either increase or decrease the antenna
position in increments of 10 or 1. After you have set the desired
number, touch ‘OK’.
4. The Home Screen will display and you can begin guidance.
Helpful Hints:
• Normally the antenna position is set in
reference to the application location.
• If you touch ‘Cancel’ on either of the two
configuration screens above, you will be
prompted again to set these the next time you
power-on the Envizio Plus system.
• This is the overall boom width for guidance.
To configure individual booms, see the
configuration section.
3
Home Screen Areas
1. GPS Status - Shows a green check mark if GPS is detected, a red ‘X’ if not.
Touch the icon to view the GPS Status screen and the ‘Auto Detect’ setting. May
also show a yellow caution.
2. File Space Status - Shows the internal memory remaining, as well as the
memory status of the USB storage device, if attached. A green check mark
appears if the memory space is OK, a yellow warning if memory is low, and a
red ‘X’ if there is no memory available. Touch the icon to show the remaining
memory available.
3. Log Status- A green check mark indicates that the log status is ‘On’ and
that a coverage map will be saved to the internal memory. A red ‘X’ indicates
that the job will not be logged. Touch the icon to turn the log on or off.
4. Screen Name and Time - Shows the current screen name and time.
Note: The time is only available if the Envizio Plus system is receiving RMC or
ZDA NMEA messages.
5. Job Status - Shows the current status of the job as well as the job name that
is displayed (if a job is started).
6. Start Guidance - Starts any new job. Touch the ‘Start Guidance’
button to start a new job.
7. Open Old Job- Opens a previous or existing job. Touch the ‘Open Old
Job’ button to view and select existing jobs.
8. Shut Down - Shuts down the system. Touch the ‘Shut Down’ button to
shut down the system.
9. Configuration Pages - Touch the ‘Configuration Pages’ button to show
and/or change configuration settings for Swath Configuration, Antenna
Position, Lightbar Configuration, Boom Control, Screen Background, File
Management, Program Updates, Time Zone Settings, Display Units, Brightness
Settings, Language Settings, Demo Mode, Guidance Page Smoothing, and TM1
Tilt Sensor.
10. Software Version - Shows the current software version of the Envizio
Plus system.
1
2
3
4
6
7
8
9
510
4
Status Symbols
The following symbols can appear on the Home screen, and refer to the
status of the GPS, File space, or Log files.
Icon Name Description
Green Check Mark: This part of the system is
normal/enabled and all operating conditions are
met.
Yellow Caution: This part of the system is
receiving a warning. Operation can proceed
with caution. Touch this icon to view the
system warning.
Red ‘X’: The system is experiencing a problem
in this area or the user has elected to not use this
function. This problem may need to be corrected
before proceeding with operation. Touch this
icon to view the system problem.
5
Job Screen Features and Areas
Swath Number or Mode
Coverage Area
Distance To Line
Green indicates that the booms
are on and coverage is being logged
A-B Line
Speed, Course
or Rates (if using a
Switch to this guidance pattern
Over Ground (COG),
Guidance Line
Distance To Line
Raven console.
(touch to toggle)
Touch to enable the
AccuBoom override
if using a CAN system
6
Screen Icons
The following screen icons appear on the Guidance screen.
Icon Name Description
Menu Button: Shows the current menu options
for the job when you touch the icon.
Straight A-B Pattern: Allows you to switch to
the Straight A-B pattern from the pattern you
are presently running by touching the icon.
Last Pass Pattern: Allows you to switch to the
Last Pass pattern from the pattern you are
presently running by touching the icon.
Pivot Pattern: Allows you to switch to the
Pivot pattern from the pattern you are presently
running by touching the icon.
Zoom Out: Allows you to zoom out from the
field or area by touching the icon.
Zoom In: Allows you to zoom in on the field or
area by touching the icon.
Boom Sense Icon: This icon shows the status of
the boom, with green being ‘On’ and red being
‘Off’.
Vehicle Icon: The tip of the arrow represents
the antenna position of the vehicle and where it
is in reference to the swath line, field, etc. If
your boom sense configuration is set to ‘Touch
Vehicle Arrow’, you must touch this icon to turn
the coverage map on and off.
7
Icon Name Description
SmarTrax Icon: This icon shows the status of
the SmarTrax system, with green being system
‘On’ and the red X being system ‘Off’.
Autoboom Icons:
Autoboom is on and both booms are on.
Autoboom is on, the left boom is on, the right
boom is off.
Autoboom is on, the left boom is off, the right
boom is on.
Autoboom is on, but both booms are off.
Autoboom is off and both booms are off.
Touch the Autoboom icon to display
the Autoboom Configuration page
8
Starting Guidance
1. From the Home Screen, touch ‘Start Guidance’.
2. Touch one of the three available patterns (see the table below for
pattern descriptions).
Pattern Description
Straight A straight A-B line pattern for parallel guidance.
Pivot A 360 degree (or circle) pattern.
Last Pass Guidance based on the last nearest pass driven.
Helpful Hints: The Envizio Plus system will allow you
to save up to 100 A-B Lines. See the ‘Saving an A-B
Line’ section for more information.
9
3. Press OK to proceed with the system generated file name, or touch
‘Change Name’ to type in a name for the file.
Helpful Hints:
• The default file name contains the date and time as
received by GPS. This will only appear if the Log
status is ‘On’. If you forgot to turn the Log status
‘On’, you can go back to the Home screen and turn
it on at anytime during the job. You will then be
prompted to name the file.
• If you choose to type your own name for the file,
you can use the touch pad to type the letters of the
file name. The keypad letters (shown below) work
similar to that of a telephone. For example, touch
the ‘ABC’ button once for ‘A’, three times for the
‘C’, and so on. Once you have typed in the name,
touch OK.
Tabla de contenidos
Otros manuales de Sistema de navegación para automóviles de Raven
