Radius 350 Manual de usuario
Congratulations on your purchase of the Radius 350 business feature
phone. This business phone has been ergonomically designed to suit
professional office requirements.
This telephone performs all basic functions supported by your service
provider. It works with all analogue PBX switching systems
The caller ID memory and phone book provide a great convenience to
manage your phone calls.
The User Guide describes the installation procedures and features.
User Guide
–8ddDXDDX800+
FX500 FXFX500
1
Accessories & Content 2
Installation 2
Wall Mounting 3
Features 3
Function Buttons 5
Main Menu Settings 7
Setting Up 8
- Language 8
- Local Area Code 8
- Date & Time 8
- Recall 9
- LCD Contrast 9
- Pulse/Tone Dialling 9
- Baby Call 10
- Exit Menu 10
- Message Waiting 10
Using the Radius 350 11
- Pre-Dialling 11
- Headset 11
- Volume Control 11
- Speaker Phone 12
- Mute 12
- Redial 12
- Pause 13
Index
2
- Recall 13
One and Two-Touch Memories 13
Caller ID 15
- To Review Calls 15
- To Make Calls From Caller ID 15
- To Delete Caller ID’s 16
Phone Book Memories 16
- to Add Contacts 17
- Search 18
- Edit 18
Automatic Call Timer 19
The following items are included in this package of the Radius 350
Analogue Business Feature Phone :-
- Phone base unit with handset
- 2 x Line cords
- Instruction Guide
- Mains Power Adaptor
1) Insert one end of the curly handset cord into the socket on
the handset and the other end into the socket on the LEFT
hand side of the base unit (next to the telephone cradle).
2) Insert the supplied power adaptor small plug into the power
Accessories & Content
Installation
3
socket on the rear of the base unit. Plug the adaptor into a
mains socket and switch on.
3) Insert the required line cord into the socket marked LINE on
the rear of the base unit.
4) Wall Mounting
- Fit the desk/wall bracket to the 4 slots on the underside of
the telephone, next to the battery compartment, with “wall”
facing upwards.
- Directly beneath the hook switch push down on the latch
and pivot up.
- Drill 2 holes vertically 88mm apart on the wall where you
wish to locate the phone and insert the screws. Tighten the
screws so that the phone slots in place and fits snugly.
- Note –take care not to drill through holes or elctrical cable.
1. Speakerphone
2. Large LCD Display (8.5cm x 4cm)
3. Headset Socket (2.5mm)
4. Desktop or wall Mountable
5. 70 Incoming Caller ID Memories
6. 70 Phone Book Memories
7. 16 Last Dialed Number Memories
8. 8 One Touch Memories and 10 Two Touch Memories
9. 16 Digit Alphanumeric display
10. 32 Digit Memory / Redial
11. FSK/DTMF dual system compatible
12. 12 Language Options
13. Local Area Code Setting
14. Time, Date,Month and Day setting
15. Recall Settings
16. Tone / Pulse setting
17. PABX code setting
18. LCD contrast setting- 5 levels
19. Mute switch
20. Electronic Ringer Hi-Lo-off
Features
4
21. Message Waiting –Line Reversal and 100v
22. Pre Dial Function
23. Call Back Function
24. Total Calls and New Calls Display
25. Pause -3.6 Sec
26. Volume control for Headset / Handset / Speaker –4 levels
27. Automatic call timer
28. Hearing Aid Compatible
29. 6v Power Adaptor Supplied
30. 2 x3m Line Cords BT & RJ45
31. 3M Extended Handset cord
32. CE & RoHs Compatible
5
Function Buttons
Description
M1 –M8
8 One touch memories (24 Digits maximum).
can store and dial frequently called number.s
Please refer to the user guide section ‘One
touch memories’
SHIFT
Using the SHIFT key up to 10 two touch
memories can be stored into the 10 key pad
buttons 1 –0
To scroll up/down when browsing selection
To review the dialled numbers. Press this
button then use keys to browse.
DELETE
To Delete an entry or a record in the memory.
Press and hold the button for more than 3
seconds, you can delete all records of the
incoming or outgoing calls.
ENTER
To enter the telephone set up menu. Dial the
numbers in predial mode
(Phone Book)
70 Contact Name and Numbers can be
stored
Function Buttons
6
(Headset / Speaker)
To accept a call or to make a call. In On
Hook mode, with headset connected, if you
press this button to take or make a call using
a headset.
If you want to use the Speaker phone,
disconnect the headset.
(Receive volume)
4 levels for receiver volume control for
Headset, Handset and Speaker Phone –Low
–Normal –Medium - High
MUTE
Press this button to Mute the Microphone. To
release mute, press the button again. The
word MUTE will be displayed on the LCD
REDIAL
(pause)
The last dialed number (upto 32 Digits) will be
retained in the redial memory. To recall a
dialed number simply lift the handset and
press the redial button.
This button can also be used to add a pause
(Pause time is 3.6 sec) when storing a PBX
access code into memories.
RECALL
Recall, also known as Flash, used to transfer
calls between extensions or to use network
services.
STORE
Used to store the 8 one touch memories
and the 10 two touch memories
7
Press and hold the “ENTER” button for 4 sec (on-hook or off hook)
the LCD displays “OPTIONS MENU ”. The following is the key
sequence when pressing the “(Up)” button.
Menu
Default
OPTIONS MENU
SET LANGUAGE
ENGLISH
LOCALAREA CODE
- - -
SET TIME/DATE
12:00 AM1/01
SET FLASH TIME
100Ms
LCD CONTRAST
3
SET TONE/PULSE
TONE
SET PBX CODE
Not applicable for
EU countries
BABY CALL
OFF
EXIT OPTIONS
Press the ENTER Button to go to the submenu, then press the (Up) or
(Down) to scroll. Press the ENTER button to save and return back or
press the RECALL button to exit.
Main menu settings
8
1. Setting language
- Press and hold the ENTER Button for 4 sec.(On hook or
Off hook)
- The LCD will show : OPTIONS MENU
- Press (Up) button
- The LCD will show : SET LANGUAGE
- Press ENTER to enter in to the menu
- Use (Up) or (Down) button to select the language
- Then ENTER button to confirm and set the language
2. Setting local area code
- Press and hold the ENTER button for 4 sec.(On hook or Off
hook)
- The LCD will show : OPTIONS MENU
- Using (Up) or (Down) button go to “LOCAL AREA CODE
MENU”
- Press ENTER button to enter in to the menu
- The LCD will show : AREACODE - - - -
- Use (Up) or (Down) button to set the area code digit by
digit, pressing ENTER to select
- Then ENTER button to confirm and set the area code.
3. Setting time & date
NB: if connected to a PABX system, some systems automatically
set date and time –please refer to the PABX user guide.
- Press and hold the ENTER button for 4 sec.(On hook or Off
hook)
- The LCD will show : OPTIONS MENU
- Using (Up) or (Down) button go to “SET TIME/DATE”
- Press ENTER to enter the menu
- The LCD will show : TIME/DATE
- Use (Up) or (Down) button to adjust the correct hour /
Minute / Month / Day at the top of the LCD
- Then ENTER button to confirm and set the time and
Setting Up
9
date.
4. Setting RECALL (flash) time
- Press and hold the ENTER button for 4 sec.(On hook or Off
hook)
- The LCD will show : OPTIONS MENU
- Using (Up) or (Down) button go to “SET FLASH TIME”
- Press ENTER to enter the menu
- The LCD will show : FLASH 300MS,
- Use (Up) or (Down) button to select the required flash
timing
- Then ENTER button to confirm and set the flash time.
Note:You have 4 options to choose from –100Ms, 300Ms, 600Ms,
1000Ms The UK standard being 100Ms
5. Setting LCD contrast
- Press and hold the ENTER button for 4 sec.(On hook or Off
hook)
- The LCD will show : OPTIONS MENU
- Using (Up) or (Down) button go to “LCD CONTRAST”
- Press ENTER to enter the menu
- The LCD will show : CONTRAST 3,
- Use (Up) or (Down) button to select the required LCD
contrast level
- Then ENTER button to confirm and set the LCD
contrast level.
6. Setting Pulse/Tone dialing mode
The Radius 350 is factory set for TONE Dialling. Should you need
PULSE dialling proceed as follows:
- Press and hold the ENTER button for 4 sec.(On hook or Off
hook)
- The LCD will show : OPTIONS MENU
- Using (Up) or (Down) button go to “SET TONE/PULSE”
- Press ENTER to enter the menu
- The LCD will show : TONE,
- Use (Up) or (Down) button to select the required dialing
Tabla de contenidos
