Radio Shack Automatic Desktop Dialer Manual de usuario
Cat. No. 43-444
90-Memory Automatic Desktop Dialer
Your RadioShack Automatic Desktop Dialer gives you easy ac-
cess to frequently called telephone numbers. Three levels of
memory storage let you store up to 90 numbers and quickly dial
each with the press of just a button or two. The dialer comes
with a 7-foot modular cord. Its features include:
32- or 33-Digit Memory — lets you store up to 32 digits (tone
mode) or 33 digits (pulse mode) in each memory location.
Quick-Reference Card — reminds you where each number is
stored.
Chain-Dialing — you can dial up to 16 stored numbers in se-
quence for banking services or long distance.
Touch-Tone or Pulse Dialing — lets you use your dialer with
either tone or pulse service.
Note: Your dialer requires 2 AAA batteries (not supplied) for
power.
Your dialer is ETL listed to UL standards and meets all applica-
ble FCC standards.
© 1998 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
43-444.fm Page 1 Friday, August 13, 1999 8:31 AM
2
This symbol is intended to alert you to the presence of unin-
sulated dangerous voltage within the product’s enclosure
that might be of sufficient magnitude to constitute a risk of
electric shock. Do not open the product’s case.
This symbol is intended to inform you that important operat-
ing and maintenance instructions are included in the litera-
ture accompanying this product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
WARNING: To reduce the risk of fire
or shock hazard, do not expose this
product to rain or moisture.
!
!
43-444.fm Page 2 Friday, August 13, 1999 8:31 AM
3
READ THIS BEFORE INSTALLATION
We have designed your dialer to conform to federal regulations,
and you can connect it to most telephone lines. However, each
device that you connect to the telephone line draws power from
the telephone line. We refer to this power draw as the device’s
ringer equivalency number
, or REN. The REN is on the bottom
of your dialer.
If you use more than one telephone or other device on the line,
add up all the RENs. If the total is more than five, your tele-
phone might not ring. In rural areas, a total REN of three might
impair ringer operation. If ringer operation is impaired, remove a
device from the line.
FCC STATEMENT
Your dialer complies with Part 68 of
FCC Rules
. You must,
upon request, provide the FCC Registration Number and the
REN to your phone company. Both numbers are on the bottom
of the dialer.
Note: You must not connect your dialer to:
• coin-operated systems
• party-line systems
• most electronic key telephone systems
43-444.fm Page 3 Friday, August 13, 1999 8:31 AM
4
INSTALLING BATTERIES
Your dialer uses two AAA batteries (not supplied) for power. For
the best performance and longest life, we recommend alkaline
batteries, such as RadioShack Cat. No. 23-555.
Cautions:
• Use only fresh batteries of the required size and recom-
mended type.
• Do not mix old and new batteries, different types of batter-
ies (standard, alkaline, or rechargeable), or rechargeable
batteries of different capacities.
Note: If you are replacing the batteries, disconnect the dialer’s
modular line cord from the telephone jack during the battery in-
stallation process.
Follow these steps to install batteries.
1. Use a screwdriver to remove the screw in the battery com-
partment cover on the bottom of the system, then remove
the cover.
2. Put fresh batteries into the compart-
ment as indicated by the polarity sym-
bols (+ and –) marked inside.
43-444.fm Page 4 Friday, August 13, 1999 8:31 AM
5
3. Replace the cover, then reinsert and tighten the screw.
When the STORE indicator flashes continuously while you are
dialing or storing a number, replace the batteries.
Cautions:
• Always remove old or weak batteries. Batteries can leak
chemicals that can destroy electronic parts.
• Dispose of old batteries promptly and properly. Do not burn
or bury them.
CONNECTING THE DIALER
Unplug your phone’s modular cord from the telephone line jack
and plug it into the dialer’s PHONE jack. Then connect one end
43-444.fm Page 5 Friday, August 13, 1999 8:31 AM
6
of the supplied line cord to your dialer’s LINE jack and plug the
other end into the telephone line jack.
STORING A NUMBER IN MEMORY
Note: The dialer stores numbers based on the dialing mode
(touch-tone or pulse dial) your phone is set to use. Be sure your
telephone is set to the desired mode before you store any num-
bers.
1. Use a paper clip (or other pointed object) to remove the
cover from the dialer’s quick-reference card, so you can
easily access the card to write down the number you store.
43-444.fm Page 6 Friday, August 13, 1999 8:31 AM
7
2. Lift the telephone’s handset and press STORE on the dialer.
The STORE indicator lights.
Note: If you are using a speakerphone, you can turn the
speakerphone on and off instead of lifting and replacing the
handset in this procedure.
3. Using the telephone’s keypad, enter the number you want
to store.
Note: If you enter a number incorrectly, replace the hand-
set and start over at Step 2.
4. Each memory button controls three locations; top (white),
middle (shaded), and bottom (gray).
• To store a number in a top (white) memory location,
press that memory button.
• To store a number in a middle (shaded) memory loca-
tion, press LEVEL 2 then the memory button.
43-444.fm Page 7 Friday, August 13, 1999 8:31 AM
8
• To store a number in a bottom (gray) memory location,
press LEVEL 3 then the memory button.
A beep sounds and the STORE indicator turns off.
5. Replace the telephone’s handset and write the name asso-
ciated with the number you stored in the appropriate white,
shaded, or gray space next to the memory button. Use a
pencil in case you need to change it later.
6. Repeat Steps 2–5 for each number you want to store.
7. Replace the quick-reference card’s cover when you finish.
Entering a Pause
In some telephone systems, you must dial an access code (9,
for example) and wait for a second dial tone before you can dial
an outside number. You can store the access code with the
phone number. However, you should also store a pause after
the access code to allow the outside line time to connect. To en-
ter a 3-second pause, press STORE.
Notes:
• You may store more than one pause in a row.
• Each pause counts as one digit in memory.
Testing Stored Emergency Numbers
If you store an emergency service’s number (police department,
911, fire department) and you choose to test the stored number,
43-444.fm Page 8 Friday, August 13, 1999 8:31 AM
9
make the test call during the late evening or early morning
hours to avoid peak demand periods. Also, remain on the line to
explain the reason for your call.
DIALING A NUMBER IN MEMORY
Lift the telephone’s handset then:
• for numbers in a top (white) location, press the memory
button.
• for numbers in a middle (shaded) location, press LEVEL 2
then the memory button.
• for numbers in a bottom (gray) location, press LEVEL 3 then
the memory button.
Your dialer dials the stored number.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as alter-
nate long distance or bank by phone), store each group of num-
bers in its own memory location.
To use a service number, dial the service’s main number first
then press STORE at the appropriate place in the call. Press the
memory button for the location where the additional information
is stored. You can dial up to 16 digits in sequence.
43-444.fm Page 9 Friday, August 13, 1999 8:31 AM
10
REPLACING/ERASING A STORED
NUMBER
To replace a stored number, simply store a new number in its
place.
To erase a stored number and leave that memory location emp-
ty, follow the steps listed in “Storing a Number in Memory,” on
Page 6 except do not enter a number in Step 3.
MAINTENANCE
To enjoy your RadioShack 90-Memory Automatic Desktop Dial-
er for a long time:
• Keep the dialer dry. If it gets wet, wipe it dry immediately.
• Use and store the dialer only in normal temperature envi-
ronments.
• Handle the dialer gently and carefully. Do not drop it.
• Keep the dialer away from dust and dirt.
• Wipe the dialer with a damp cloth occasionally.
Modifying or tampering with the dialer’s internal components
can cause a malfunction and might invalidate its warranty. If
your dialer is not performing as it should, take it to your local
RadioShack store for assistance. If the trouble is affecting the
telephone lines, the phone company can ask you to disconnect
your dialer until you have resolved the problem.
43-444.fm Page 10 Friday, August 13, 1999 8:31 AM
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema telefónico de Radio Shack
