Racal Instruments 1260 Manual de usuario

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF

IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF

MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY

RENTALS

• ITAR CERTIFIED

SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff

at our full-service, in-house repair center

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment

We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

REMOTE INSPECTION

Remotely inspect equipment before purchasing with

our interactive website at www.instraview.com

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more

information on price quotations, drivers, technical

specications, manuals, and documentation

View

Instra

1260 VXI

SWITCHING CARD

1260-35

MULTIPLEXER / SCANNER

PUBLICATION NO. 980673-006

RACAL INSTRUMENTS

Racal Instruments, Inc.

4 Goodyear St., Irvine, CA 92618-2002

Tel: (800) 722-3262, FAX: (949) 859-7309

Racal Instruments, Ltd.

480 Bath Road, Slough, Berkshire, SL1 6BE, United Kingdom

Tel: +44 (0) 8706 080134; FAX: +44 (0) 1753 791290

Racal Systems Electronique S.A.

18 Avenue Dutartre, 78150 LeChesnay, France

Tel: +33 (1) 3923 2222; FAX: +33 (1) 3923 2225

Racal Systems Elettronica s.r.l.

Strada 2-Palazzo C4, 20090 Milanofiori Assago, Milan, Italy

Tel: +39 (02) 5750 1796; FAX +39 (02) 5750 1828

Racal Elektronik System GmbH.

Frankenforster Strasse 21, 51427 Bergisch Gladbach, Germany

Tel:+49 2204 92220; FAX: +49 2204 21491

Racal Australia Pty. Ltd.

3 Powells Road, Brookvale, NSW 2100, Australia

Tel: +61 (2) 9936 7000, FAX: +61 (2) 9936 7036

Racal Electronics Pte. Ltd.

26 Ayer Rajah Crescent, 04-06/07 Ayer Rajah Industrial Estate, Singapore 0513.

Tel: +65 7792200, FAX: +65 7785400

Racal Instruments, Ltd.

Unit 5, 25F., Mega Trade Center, No 1, Mei Wan Road, Tsuen Wan, Hong Kong, PRC

Tel: +852 2405 5500, FAX: +852 2416 4335

http://www.racalinst.com

PUBLICATION DATE: April 10, 2000

This book or parts thereof may not be reproduced in any form without written permission of the publisher.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

WARRANTY STATEMENT

All Racal Instruments, Inc. products are designed and manufactured to exacting standards and in full

conformance to Racal’s ISO 9001 procedures.

For the specific terms of your standard warranty, or optional extended warranty or service agreement, contact

your Racal customer service advisor. Please have the following information available to facilitate service.

1. Product serial number

2. Product model number

3. Your company and contact information

You may contact your customer service advisor by:

E-Mail: [email protected]

Telephone: +1 800 722 3262 (USA)

+44(0) 8706 080134 (UK)

+852 2405 5500 (Hong Kong)

Fax: +1 949 859 7309 (USA)

+44(0) 1628 662017 (UK)

+852 2416 4335 (Hong Kong)

RETURN of PRODUCT

Authorization is required from Racal Instruments before you send us your product for service or calibration. Call

your nearest Racal Instruments support facility. A list is located on the last page of this manual. If you are

unsure where to call, contact Racal Instruments, Inc. Customer Support Department in Irvine, California, USA at

1-800-722-3262 or 1-949-859-8999 or via fax at 1-949-859-7139. We can be reached at:

[email protected].

PROPRIETARY NOTICE

This document and the technical data herein disclosed, are proprietary to Racal Instruments, and shall not,

without express written permission of Racal Instruments, be used, in whole or in part to solicit quotations from a

competitive source or used for manufacture by anyone other than Racal Instruments. The information herein has

been developed at private expense, and may only be used for operation and maintenance reference purposes or

for purposes of engineering evaluation and incorporation into technical specifications and other documents which

specify procurement of products from Racal Instruments.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FOR YOUR SAFETY

Before undertaking any troubleshooting, maintenance or exploratory procedure, read carefully the

WARNINGS and CAUTION notices.

This equipment contains voltage hazardous to human life and safety, and is capable of inflicting

personal injury.

If this instrument is to be powered from the AC line (mains) through an autotransformer, ensure the

common connector is connected to the neutral (earth pole) of the power supply.

Before operating the unit, ensure the conductor (green wire) is connected to the ground (earth)

conductor of the power outlet. Do not use a two-conductor extension cord or a three-prong/two-

prong adapter. This will defeat the protective feature of the third conductor in the power cord.

Maintenance and calibration procedures sometimes call for operation of the unit with power applied

and protective covers removed. Read the procedures and heed warnings to avoid “live” circuit

points.

Before operating this instrument:

1. Ensure the instrument is configured to operate on the voltage at the power source. See

Installation Section.

2. Ensure the proper fuse is in place for the power source to operate.

3. Ensure all other devices connected to or in proximity to this instrument are properly grounded or

connected to the protective third-wire earth ground.

If the instrument:

-fails to operate satisfactorily

-shows visible damage

-has been stored under unfavorable conditions

-has sustained stress

Do not operate until performance is checked by qualified personnel.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

This page was left intentionally blank.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Amendment Page 6/98 1

NOTE FOR SYSTEMS WITH 1260-OPT 01T

The “Module-Specific Syntax” section of this manual shows the command syntax for the

1260-01S Smart Card. If you are using the newer 1260-01T Smart Card, the commands

will NOT work as shown.

Consult the 1260-01T Manual for a description of the commands that may be used with the

1260-01T Smart Card.

The channel numbers described in this manual are valid for the 1260-01T. The channel

numbers continue to be used for the 1260-01T.

The syntax of the commands that use channel numbers has changed for those cards

controlled by the 1260-01T.

The new syntax used to close a channel is:

CLOSE (@ <module address> ( <channel> ) )

For example, for a relay module whose <module address> is set to 7, closing <channel> 0

is performed with the command:

CLOSE (@7 (0))

Using the older 1260-01S, the command would be (as shown in this manual):

CLOSE 7.0

Many other command syntax differences exist. Please consult chapter 2 of the 1260-01T

manual for a description of the commands that are available for the 1260-01T.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Control Information for the 1260-35A

The 1260-35A operates as a 4-wire MUX. Thus, when a channel is operated, 2 relays must be operated in

parallel. For each channel, when a bit of Control Register X is set (or cleared), the same bit of Control

Each channel on this module is therefore controlled by setting or clearing two bits, one each in two different

Control Registers. Control Registers on the module operate 8 channels simultaneously. There are eight

control bits per Control Register. Setting the bit to a 1 closes the relay; setting the bit to a 0 opens the relay.

The table below shows the mapping between logical channels used to operate the relay module in message-

based mode and the bits within the Control Registers which may be used to operate the channel in register-

based mode.

Each Control Register is located 2 addresses from the previous Control Register. That is, each Control

is located at the “Base A24 Address” for the module. Consult the “Register-Based Operation” Section of

Chapter 2 of the 1260-01T manual for a description of calculating control register addresses

For example, when closing channel 13, both byte 1 and byte 7 must have bit 5 set.

Channel Control Register Control Bit

0 0 and 6 0

1 0 and 6 1

2 0 and 6 2

3 0 and 6 3

4 0 and 6 4

5 0 and 6 5

6 0 and 6 6

7 0 and 6 7

8 1 and 7 0

9 1 and 7 1

10 1 and 7 2

11 1 and 7 3

12 1 and 7 4

13 1 and 7 5

14 1 and 7 6

15 1 and 7 7

16 2 and 8 0

17 2 and 8 1

18 2 and 8 2

19 2 and 8 3

20 2 and 8 4

21 2 and 8 5

22 2 and 8 6

23 2 and 8 7

24 3 and 9 0

25 3 and 9 1

26 3 and 9 2

27 3 and 9 3

28 3 and 9 4

29 3 and 9 5

30 3 and 9 6

31 3 and 9 7

32 4 and 10 0

33 4 and 10 1

34 4 and 10 2

35 4 and 10 3

36 4 and 10 4

37 4 and 10 5

38 4 and 10 6

39 4 and 10 7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Channel Control Register Control Bit

40 5 and 11 0

41 5 and 11 1

42 5 and 11 2

43 5 and 11 3

44 5 and 11 4

45 5 and 11 5

46 5 and 11 6

47 5 and 11 7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Control Information for the 1260-35B

The following information describes the control-register-to-relay-channel mapping for a 1260-35B Relay

Module. This information may be used to control a 1260-35B when using a 1260-01T in the register-based

mode of operation.

Each relay on this module is controlled by setting or clearing a single bit within a Control Register. Control

Registers on the module operate 8 channels simultaneously. There are eight control bits per Control Register.

Setting the bit to a 1 closes the relay; setting the bit to a 0 opens the relay.

The table below shows the mapping from logical channels to control bits. The logical channels are used when

operating the relay module in message-based mode. The control bits within the Control Registers are used to

operate the module in register-based mode.

Each Control Register is located 2 addresses from the previous Control Register. That is, each Control

is located at the “Base A24 Address” for the module. Consult the “Register-Based Operation” Section of

Chapter 2 of the 1260-01T manual for a description of calculating control register addresses.

Channel Control Register Control Bit

000

101

202

303

404

505

606

707

810

911

10 1 2

11 1 3

12 1 4

13 1 5

14 1 6

15 1 7

16 2 0

17 2 1

18 2 2

19 2 3

20 2 4

21 2 5

22 2 6

23 2 7

24 3 0

25 3 1

26 3 2

27 3 3

28 3 4

29 3 5

30 3 6

31 3 7

32 4 0

33 4 1

34 4 2

35 4 3

36 4 4

37 4 5

38 4 6

39 4 7

40 5 0

41 5 1

42 5 2

43 5 3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Channel Control Register Control Bit

44 5 4

45 5 5

46 5 6

47 5 7

48 6 0

49 6 1

50 6 2

51 6 3

52 6 4

53 6 5

54 6 6

55 6 7

56 7 0

57 7 1

58 7 2

59 7 3

60 7 4

61 7 5

62 7 6

63 7 7

64 8 0

65 8 1

66 8 2

67 8 3

68 8 4

69 8 5

70 8 6

71 8 7

72 9 0

73 9 1

74 9 2

75 9 3

76 9 4

77 9 5

78 9 6

79 9 7

80 10 0

81 10 1

82 10 2

83 10 3

84 10 4

85 10 5

86 10 6

87 10 7

88 11 0

89 11 1

90 11 2

91 11 3

92 11 4

93 11 5

94 11 6

95 11 7

96 12 0

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Otros manuales para 1260

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Racal Instruments

Racal Instruments

Racal Instruments 1260 VXI Manual de usuario

Racal Instruments

Racal Instruments 2460 Series Manual de usuario

Racal Instruments

Racal Instruments 1260-38 Manual de usuario

Racal Instruments

Racal Instruments 1260 Manual de usuario

Racal Instruments

Racal Instruments 7064R-S-1844 Manual de usuario

Racal Instruments

Racal Instruments 1260 Manual de usuario

Racal Instruments

Racal Instruments 1260-93 Manual de usuario

Racal Instruments

Racal Instruments 1260 VXI Manual de usuario

Racal Instruments

Racal Instruments 1260 Manual de usuario

Racal Instruments

Racal Instruments 1260-17 Manual de usuario

Racal Instruments

Racal Instruments 1260 VXI Manual de usuario

Racal Instruments

Racal Instruments 1260-50A Manual de usuario

Racal Instruments

Racal Instruments 7064R-S-1843 Manual de usuario

Racal Instruments

Racal Instruments 1260 VXI Manual de usuario

Racal Instruments

Racal Instruments 1260-132 Manual de usuario

Racal Instruments

Racal Instruments 1260-43 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario