R2TECK DVL-2 Manual de usuario
Digital Video Transmission System
DVL-2
USER MANUAL
Wuxi R2TECK Co.,Ltd
Content
1. EASY WAY TO START THE DEVICE...........................................................................................................1
2. SPECIFICATION.............................................................................................................................................. 3
3 INTRODUCTION................................................................................................................................................4
3.1 Disclaimer................................................................................................................................................ 4
3.2 Profile....................................................................................................................................................... 4
3.3 Intended usage....................................................................................................................................... 4
3.4 Caution..................................................................................................................................................... 4
4. PRODUCT OVERVIEW...................................................................................................................................6
4.1 Brief introduction.....................................................................................................................................6
4.2 Standard spec.........................................................................................................................................6
5. PORT DEFINITION.......................................................................................................................................... 8
5.1 Transmitter port.......................................................................................................................................8
5.1.1 Back side......................................................................................................................................8
5.1.2 Right side port............................................................................................................................. 8
5.1.3 Front side port........................................................................................................................... 10
5.2 Receiver port.........................................................................................................................................10
5.2.1 Bottom side port........................................................................................................................10
5.2.2 Left side port.............................................................................................................................. 11
5.2.3 Right side port........................................................................................................................... 12
5.2.4 Front side port........................................................................................... 错误！未定义书签。
6. INSTALLATION...............................................................................................................................................16
6.1 Transmitter installation........................................................................................................................ 16
6.2 Receiver installation............................................................................................................................ 16
7. BIND AND FREQUENCY SWITCH.............................................................................................................17
8. APP INSTRUCTION.......................................................................................................................................18
8.1 OSD setting...........................................................................................................................................18
8.2 Power setting........................................................................................................................................ 18
9. TROUBLES SOLUTION................................................................................................................................19
9.1 Trouble symptoms / diagnosis / solution..........................................................................................19
10. APPENDIX.....................................................................................................................................................22
10.1 Video resource requirement.............................................................................................................22
10.2 Monitor OSD content.........................................................................................................................22
1
1. Easy way to start the device
1.1 Operating steps and instructions
1.1.1 OSD module
Install GPS module.
Install voltage monitoring cable.
Install OSD Data output cable.
Install Mavlink data cable. (optional, if you do not need, just go to next step.)
Turn on the power (Transmitter supply the power).
There should be below instructions if the OSD module works well.
Power indication LED3 red light turn-on, LED2 blue light flash.
LED3 blue light turn-on if 4 satellites could be searched
1.1.2 Transmitter
Install the antennas.
Install the HDMI camera cable.
Install OSD data output cable.
Connect camera to the power, select the correct video format.
Place the Transmitter in horizontal position, connect transmitter to the power.
There should be below instructions if the transmitter works well.
WORK light flash regularly.
HDMI light turn-on
LINK light turn-on if the transmitter connect to receiver.
1.1.3 Receiver
Install the antennas
Install the monitor by HDMI cable. (optional)
Install USB-to serial port adapter. (optional)
Install GPS on the receiver.
Connect to the power. (battery of 12V-DC power)
Turn on the power.
There should be below instructions if the receiver works well.
Upper cabin: Power light turn-on, MODE light flash twice. Will start sensor calibration when upper cabin
clockwise rotation on 2~3 weeks and then Counterclockwise rotation 2 to 3 weeks. Antennas point to
North if calibrate success (for the North please refer compass). Please press LEFT FINE-TUNE and
RIGHT FINE-TUNE button for adjustment the direction if have deviation.
Below cabin:
WORK light flash regularly
HDMI light turn-on(if installed the HDMI monitor).
LINK light turn-on if the transmitter connect to transmitter.
HDMI monitor instruction (if installed the HDMI monitor):
2
The monitor shows logo "R2TECK" after receiver connect to the power.
After that, the monitor shows progress bar: Start-up / Selfcheck / Link.
Monitor real-time display the camera video when the transmitter connect to receiver.
Wait upper cabin GPS light turn-on.
When the monitor display is normal, place the transmitter and receiver to the same position. Press
POSITION CONFIRM button 2 seconds to confirm the coordinate of starting point. GPS light flash means
the coordinate successful be confirmed.
After that, don’t move the receiver position (please confirm the coordinate again in offline status if move
the receiver position).
Make transmitter from receiver more than 10 meters away, press MODE button 2 seconds, will switch
from offline mode to tracking mode. MODE light turn-on.
1.1.4 Mobile
The mobile connect the wifi network "R2TECK_DVL1", WIFI password "12345688"
wait for connecting
Run the APP (if the APP is already running, turn off it first then run again)
The mobile real-time display the camera video, the MOBILE light on the receiver turn-on.
Attention: Currently only allow working one mobile, if want to change the mobile, please follow below process:
Disconnect the mobile with receiver wifi network.
Wait receiver MOBILE light turn off.
Repeat the above 4 steps.
IOS App installation: In App store, search the key word “r2teck”and download.
Android installation: In 360 mobile assistant, search the key word “r2teck” and download.
In Google play, search the key word “r2teck” and download.
3
1.1.3.1
2. Specification
Here list the detailed specification about DVL2
2.1.1
Function specification
Communication distance (outdoor,
no obstruction)
800mw ground distance ≥6000m
Output Power (EIRP)
25mw-800mw adjustable
Sensitivity
-95dbm±2dbm
Frequency
5G
Physics specification
working temperature
-10~60℃
storage temperature
-20~50℃
dimension (including the shell, not
including the antennas)
Transmitter: L.75.5mm x W. 54.5mm x H. 22mm
Receiver: L.330mm x W. 395mm x H. 360mm
Weight (including the shell, not
including the antennas)
Transmitter: 102g
Receiver: 4.6kg
Hardware function support
Transmitter working voltage
2S~3S，DC-12V
Receiver working voltage
3S，DC-12V
Receiver working current
＞2A (DC-12V)
2.1.2 OSD Specification & Functions
Physical Parameters:
Weight of OSD Data collect module
3.9g
Volume of OSD Data collect module
38*27*5.6(mm)
GPS module weight
29g
GPS module volume
54*15(mm)
Power Supply:
Voltage of Data collection module
DC 5.0V±5%
Voltage of GPS module
DC 5.0V±5%
4
3 Introduction
3.1 Disclaimer
Thanks for purchasing the DVL2 from Wuxi R2TECK. Everyone need to read and understand this
disclaimer before using the DVL2. You are supposed to be accepted the disclaimer once the product is
started to use. Please comply with the installation and using process indicated in this use manual. Wuxi
R2TECK will not be responsible for the consequence of the improper use, improper install, improper
modify.
The product name, brand mentioned here are belong to R2TECK.
3.2 Profile
This use manual as the instruction of Full-HD Digital Video Transmission system DVL-2, the
components and functions mentioned here may not be the standard spec. please check the enclosed list
with the product, please contact with the dealer if you have any question
The right of the manual write, modify and release only belong to Wuxi R2TECK, Without the
authorization of Wuxi R2TECK, this use manual could not be copied or modified or released
The information in this manual is only for DVL2 Full-HD Digital Video Transmission System.
This manual is subject to change without prior notice.
Version
profile code & version
release date
RR.H.0002. 0017. V01
2017.11
3.3 Intended usage
DVL-2 use for wireless Full-HD Digital Video transmission
3.4 Caution
The effectiveness of the use recorder is subject to if comply with operate and maintain
direction in this manual.
Before start the product, the staff must make sure the operate process and condition is
5
correct. specially to check the product cables are good or not, if the cable is damaged,
please change it before start the product.
DVL-2 is intended to use on the UAV and other Full-HD digital video transmission. DVL-2
may not be reached the defined function if it works in the improper temperature, improper
humidity and improver air pressure.
DVL-2 should not work when it is wet. Have to make sure it is dry when you use it.
DVL-2 is the high precise product, it is forbid to beat and clash.
Product life time is 2 years, quality warranty is 1 year.
Manufacture and dealer are responsible for the product maintenance, without the
authorization, please don't fix the product and don't modify the product.
6
4. Product overview
4.1 Brief introduction
DVL-2 is the auto antenna tracker 1080p full-HD Digital Video transmission system which including
OSD module、air part and ground part, it transmit the video and image by the wireless communication
mode. DVL-2 is perfect for the transmission distance because of the receiver antennas can be
automatically adjusted. Please install the transmitter and OSD module on the aircraft, connect the
receiver to the monitor or mobile phone to monitoring the video.
4.2 Standard spec
4.2.1 product main part
Transmitter x 1
Receiver x 1
Transmitter antenna x 2
Receiver antenna x 2
7
Receiver mobile antenna x 2
4.2.1 OSD module part
OSD Data collection module
×1
GPS module
×1
Voltage monitoring cable
×1
OSD Data output cable
×1
Mavlink data cable
×1
4.2.3 Receiver cable
Transmitter power cable x 1 (standard)
Transmitter power cable 12V
HDMI cable (D-D) x 1
Camera HDMI cable
4.2.3 Transmitter cable
USB to serial adapter x 1 (Standard)
Receiver Mavlink data cable (Red:
VCC; Black: GND; White: TX; Green:
RX)
8
5. Port definition
5.1 Transmitter port
5.1.1 Back side
5.1.1.1
[1]: For frequency switch setting
Press the button more than 5 seconds, 4 lights (HDMI, LINK, OSD, WORK) are all turn-off,
release the key, 4 lights flash as 0.5Hz frequency, and then 4 lights back to normal state, that
means channel change is finished. If devices not connected yet after 10 seconds of frequency
switch process, please switch again. The frequency supported by device as below：
5180
5220
5260
5320
5520
5540
5560
5580
560
5620
5640
5660
5680
5700
[2]: For bind the transmitter and receiver.
Press the button more than 5 seconds, 4 lights (HDMI, LINK, OSD, WORK) are all turn-off, then
4 lights flash one by one, when the LED light works well that means they are well bind. This may
takes 2 minutes. If the connection has not been resumed after 2 minutes, repower on both ends,
and don’t need rebind.
5.1.2 Right side port
5.1.2.1
Tabla de contenidos
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
