Quicksilver M135 Manual de usuario

Quicksilver Audio M135Mono Amplifier

Operating Instructions

Thank you for purchasing the Quicksilver Audio M135 Mono Amplifiers. These amplifiers have been engineered to

have a very wide bandwidth, extremely low distortion and superior dynamic range.

Theoutputtransformerusedinthisamplifierisbasedonthebestdesignsofthepastbutusessuperiornewmaterials

to achieve a very high level of performance. The high frequency characteristics of this transformer are so stable that

many different output tubes may be used without the need for circuit changes or compensation adjustments.

The front end circuitry used in this amplifier was developed by Quicksilver and is unique to the audio industry. It is

D.C. coupled for low frequency stability, and nulls out any change in power supply voltages, negating the need for

regulated power supplies and their inherent sonic problems.

This is an all tube design and uses no circuit boards or transistors.

This device has very high internal voltages. Never operate with the bottom removed!

Never operate your amplifers with the speakers disconnected.

Toprolongthelifeofyouramplifiers,neverturnthemonandoffwithinashortperiodoftime

(45 seconds.)

PLACEMENT

The M135 Mono Amplifiers should have at least 6 inches of ventilation space on either side and

at least 10 inches above them. If this is not possible, then use a fan for cooling.

SPEAKER CONNECTION

Five-way binding posts are used for speaker connection. For better sonic performance, we

recommend using the screw-down part of the post rather than banana plugs to connect your

speakerwire. Makesuretheleadsdonottoucheachother. Theratingonthebackofyourspeaker

system will determine whether you use the 4 or 8 ohm tap.

INPUT

100K

Serial Number Plate

SYSTEM GROUNDING

Your Mono Amplifiers come with three pronged grounded AC plugs. In some systems, where the

preamp is also grounded, a ground loop may appear as a low level hum. Using an adaptor on the

AC plug, to lift the ground, will solve this problem.

4Ω8ΩFuse

Power cord

4 AMP SLO-BLO FUSE

Standard fuse value must not be exceeded. If a fuse blows, replace and check output tube bias.

If there is a large change in any tube, then that tube is probably damaged. If the bias has not

changed then the cause of the fuse blowing may be due to other problems, such as poor system

grounding,unstablepreamp,shortedspeaker,etc. Interchangingtheampsbetweenchannelswill

help localize the problem to either the system or the amplifier.

TUBES

Theinputtubesinthisamplifierwerechosenfortheirspecificperformancecharacteristics.These

tubes should last several years or many thousands of hours. We can only guarantee the

performance of this unit when used with input tubes supplied by Quicksilver.

Quicksilver ships the M135 Amplifiers with matched EL34 output tubes but the M135 can use a

variety of output tubes. The output tubes do not need to be matched however matched tubes can

provide better performance.

Outputtubeswillneedtobe replaced periodically. When adegradationinsoundoccurs, thefuse

blows repeatedly or the tubes will not hold their bias anymore it is time for new output tubes. We

recommend purchasing tubes from Quicksilver Audio or your dealer and we recommend keeping

an extra output tube on hand in the event that one fails.

OUTPUT TUBE BIAS SETTING

Output tube bias should be set immediately when new tubes are put in; then again in 15 minutes;

and periodically the first few times of using the amplifiers. After that the bias should be checked

monthly.

Thebiasmustbesetcorrectlyforthetypeofoutputtubethatisused.Themaximumsettingforeach

tube is as follows:

EL34 45ma

KT77 50ma

6L6 50ma

6550 60ma

KT88 60ma

Bias controls are behind the door near the right front panel handle. Open the door by applying

pressure with a finger at the bottom right. To check the bias push in the control for the tube you

want to check. Each tube corresponds to the control nearest it.

To adjust the bias you will need a slot-head screwdriver. Adjust by turning clockwise to increase

bias; counterclockwise to decrease bias. Do this for each of the six output tubes. Actual bias is

shownonthefrontpanelbiasmeter. TheM135canuseavarietyofoutputtubes. Rememberthat

bias set above the recommended values will wear out your tubes prematurely.

If you depress two or more jacks at the same time the meter averages the readings of the tubes,

so your meter will not be damaged. Tube biases should be checked individually.

WARRANTY

Quicksilver Audio warranties your amplifiers for a period of 3 years from the date of purchase

(90 days on tubes.) Parts and labor are provided free of charge as long as the failure was not

caused by misuse, accident or negligence. Shipping to the factory is not included.

Retain at least one packing carton in case a unit needs to be returned for service.

Quicksilver Audio

5635 Riggins Court, Unit 15

Reno, NV 89502

(775) 825-1514 / Fax 825-1552

www.quicksilveraudio.com

Quicksilver Audio M135 Mono Amplifiers

SPECIFICATIONS

Power Output =135 watts into 4 or 8 ohms

from 20Hz to 20 KHz

Power Bandwidth =10 Hz to 100 KHz

Input Sensitivity =1.33 volts

Power Supply

Energy Storage =575 joules

Dimensions

- Chassis = 13“ deep x 17” wide x 8” high

- Front panel =19" wide x 8 3/4" high,

Rack handles 2" deep

Finish - Chassis =Textured black

- Front panel =Silver anodize,

Rack handles black

Weight =70 lbs

Tube Complement = 1 - 12FQ7

1 - 12AU7

6 - EL34

Warranty =3 years parts and labor

Tubes 90 days

Tabla de contenidos

Otros manuales de Amplificador de Quicksilver

Quicksilver

Quicksilver 88 Manual de usuario

Quicksilver

Quicksilver Silver 60 Mono Manual de usuario

Quicksilver

Quicksilver Integrated amplifier Manual de usuario

Quicksilver

Quicksilver Audio V4 Manual de usuario

Quicksilver

Quicksilver Quicksilver Audio V4 Mono Amplifier Manual de usuario

Quicksilver

Quicksilver 8417G Manual de usuario

Quicksilver

Quicksilver Mini-Mite Manual de usuario

Quicksilver

Quicksilver M60 Manual de usuario

Quicksilver

Quicksilver KT Series Manual de usuario

Quicksilver

Quicksilver Remote Control Line Stage Preamplifier Manual de usuario

Quicksilver

Quicksilver Line Stage Preamplifier Manual de usuario

Quicksilver

Quicksilver Triode Mono Amplifier Manual de usuario

Quicksilver

Quicksilver GLA Manual de usuario

Quicksilver

Quicksilver Preamplifier Manual de usuario

Quicksilver

Quicksilver Mid Mono Manual de usuario

Quicksilver

Quicksilver Phono Stage Preamplifie Manual de usuario

Quicksilver

Quicksilver Audio M80 Manual de usuario

Quicksilver

Quicksilver SET Mono Amplifier Manual de usuario

Quicksilver

Quicksilver Audio Mono 100 Manual de usuario

Quicksilver

Quicksilver Sixty Watt Mono Amplifier Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario