Quell Q4000DCS-WCB Manual de usuario

INTELLIGENT WIRELESS

Smoke Alarm User Guide

Photoelectric Smoke Alarm with Voice

and Wireless Interconnect – Battery Operated

Model Q4000DCS-WCB

Model Q4000DCS-WCL

Model Q4000DCS-WBB

Model Q4000DCS-WBL

Model Q4000LDCS-WCH (Safety Light)

Model Q4000LDCS-WBH (Safety Light)

WIRELESS INTERCONNECT:

You do NOT need a home wi-fi system to use

these units. Multiple wireless units create their

own independent wireless alarm network.

Quell alarms connect to each other wirelessly

via communication on the 915-928 MHz band.

10YEAR SEALED

LITHIUM BATTERY

WIRELESS INTERCONNECT

VOICE ALARM

PHOTOELECTRIC SMOKE ALARM

P/N: 137071, 137073, 137077,

137072, 137074, 137078

P/N:0316-7201-02

Thank You for Purchasing this Quell®Smoke Alarm

These models are powered by a non-replaceable, long life sealed lithium battery system, and include SMART HUSH

Control to temporarily silence nuisance alarms. They are capable of interconnecting wirelessly via RF signals.

READ SECTION 7: Activation and Wireless Alarm Network, before powering the units. You do NOT need a

home wi-fi system to use these units. Quell®alarms connect to each other wirelessly via communication on

the 915-928 MHz band.

Teach children how to respond to the alarm and that they should never play with the unit.

Your Quell®Smoke Alarm was designed for use in a residential environment.

NOTE: Please thoroughly read this user guide and save the document for future reference and to pass on to any

subsequent owner.

Quell® is a registered trademark of Kidde Australia Pty Ltd.

Contents

1. Product features . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Product Specifications . . . . . . . . . . . . . . . . . . . . . . . 4

3. Recommended Locations for Smoke Alarms . . . . . . . . . . . . . . . 5

4. Locations To Avoid . . . . . . . . . . . . . . . . . . . . . . . . . 8

5. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. Installation / Mounting Instructions . . . . . . . . . . . . . . . . . . 10

7. Activation and Wireless alarm network . . . . . . . . . . . . . . . . . 11

7.1 Setting up a wireless alarm network . . . . . . . . . . . . . . . . . 11

7.2 Adding another device to an existing wireless alarm network . . . . . . . 12

7.3 Resetting a Device’s Wireless Settings . . . . . . . . . . . . . . . . 13

8. Operation and Testing . . . . . . . . . . . . . . . . . . . . . . . 14

9. Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . 15

10. Other Alarm Visual and Audible Indicators. . . . . . . . . . . . . . . . 18

11. Recognizing Nuisance Alarms . . . . . . . . . . . . . . . . . . . . 19

12. Bat tery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

13. Permanently Disable Alarm / Discharge Battery. . . . . . . . . . . . . . 20

14. Cleaning Your Alarm . . . . . . . . . . . . . . . . . . . . . . . . 21

15. Good Safety Habits . . . . . . . . . . . . . . . . . . . . . . . . 21

16. What To Do When The Alarm Sounds . . . . . . . . . . . . . . . . . 22

17. Warranty & Contact Details . . . . . . . . . . . . . . . . . . . . . 23

18. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1. Product features

The Q4000 series is powered from a non-replaceable battery. The smoke alarm ensures protection in the event of a

power failure.

•Smoke Alarm SMART HUSH Control

•Voice message system

•Powered by 3V DC non-replaceable sealed lithium battery.

•Wireless interconnectable to QUELL compatible alarms.

•One large, user- friendly button.

•LED safety light on model Q4000LDCS-WCH and Q4000LDCS-WBH to help illuminate escape pathways

2. Product Specifications

Models

Q4000DCS-WCB with voice

Q4000DCS-WBB with voice

Q4000DCS-WCL with voice

Q4000DCS-WBL with voice

Q4000LDCS-WCH with Light

Q4000LDCS-WBH with Light

Electrical Rating

3V sealed lithium battery

Radio Frequency

925MHz

Sensor

Photoelectric

Wireless Interconnecting

Smoke Alarms

up to any combination of 23 QUELL wireless smoke alarms models. Compatible

models are Q2300W and Q4000 Series

Wireless Range At least 100m line of sight. Distance vary depending on obstructions.

Operating Temperature 0 °C to 40°C

Operating Humidity Up to 93% Humidity (Non-Condensing)

Storage and Transport Conditions - 20° C to +60° C, 5-95%RH (non-condensing)

Audiable Alarm 85 decibels at 3 metres with voice message “Fire!”

3. Recommended Locations for Smoke Alarms

Refer to your local state and federal laws or contact your local fire brigade to determine the minimum

installation requirements (Figure 3.1 A and Figure 3.1 B ).

Recommended Locations

•In every room where someone sleeps with the door closed. The closed door may prevent an alarm located outside

from waking the sleeper.

•In the immediate area of bedrooms and the exit path from all sleeping areas (Figure 3.1 A).

•In stairways, as stairways act like chimneys for smoke and heat.

•In any room where large electrical appliances are operated (e.g., portable heaters or humidifiers).

•If a hallway or room is more than 9.1m long put alarms at both ends.

•For maximum household protection see Figure 3.1 C. Ordinary residential construction.

Things to Consider:

•Smoke from a fire will rise to the ceiling and spread horizontally.

•Mounting the smoke alarm in the centre of the ceiling places it closest to all points in the room.

•When mounting an alarm on the ceiling, locate it at a minimum of 30cm from the side wall (Figure 3. 2A).

•For sloped, peaked or cathedral ceilings the alarm should be placed between 500mm and 1500mm from the highest

point of the ceiling (Figure 3.2A and 3.2B).

•Smoke alarms in rooms with ceiling slopes greater than 1m in 8m horizontally, should be located on the high side of

the room (Figure 3. 2 A ).

For Wall Mounting:

When mounting the alarm on the wall, use an interior wall with the top edge of the alarm at a minimum of 10cm and a

maximum of 30cm below the ceiling (Figure 3.2 A).

DINING

ROOM

LIVING

ROOM

Smoke Alarms for Minimum Protection

Not within 3m of cooking appliances

Smoke Alarms for Additional Protection

KITCHEN

BEDROOM

BEDROOM BEDROOM

LIVING

ROOM KITCHEN

BEDROOMBEDROOM HALL

BASEMENT

FIGURE 3.1 A FIGURE 3.1 B

FIGURE 3.1 C

SINGLE FLOOR PLAN MULTIPLE FLOOR PLAN

BEDROOM

FAMILY ROOM

WORKSHOPBASEMENT

KITCHEN

HALL

GARAGE

MASTER

BEDROOM

FIRE

EXTINGUISHERS

SMOKE

ALARMS

FIRE BLANKET

TOTAL HOME PROTECTION

CEILING

300 mm

MINIMUM

100 mm

MINIMUM

300 mm

MAXIMUM

SIDE WALL

BEST

PLACEMENT

ACCEPTABLE

PLACEMENT

DO NOT INSTALL

DEAD AIR

NOT IN

THIS AREA

ANYWHERE IN THIS

AREA

NOT IN

THIS AREA

ANYWHERE IN THIS

AREA

SLOPED CEILING

500mm

1000mm

500mm

Smoke alarm should

be located between

500mm and 1500mm

of the highest point.

DEAD AIR

DO NOT INSTALL

FIGURE 3.2 A

FIGURE 3.2 B

CEILING APEX

4. Locations To Avoid

•Smoke alarms should not be installed within 0.9m(3 ft)

•of the door to a bathroom containing a tub or shower

•forced air supply ducts used for heating or cooling

•ceiling or whole house ventilating fans

•other high air flow areas

•Areas where curtains or other objects will block the sensor. Smoke must be able to reach the sensor to accurately

detect conditions.

•Install at least 300mm away from a light fitting.

•No closer than 400 mm outside the circumference of a ceiling fan.

•Keep out of insect infested areas.

•Avoid excessively dusty, dirty or greasy areas.

•Do not install in areas where the temperature is colder than 0°C or hotter than 40°C.

•Do not install in areas where the relative humidity (RH) is greater than 93%.

•Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature and

should not be installed within 3m of cooking appliances.

•Avoid dead air spaces such as the peak of an “A” frame ceiling. “Dead Air” at the top may prevent smoke from reaching

the alarm in time to provide early warning. Refer to Figure 3.2A and 3.2B

NOTE: Smoke alarms are not to be used with detector guards unless the combination (alarm and guard) has been

evaluated and found suitable for that purpose.

5. Installation

Upon initial power being applied (from rotating onto mounting plate or moving the red activation wheel to the

“ON” position - see Figure 7.1-B) these units are ready to connect to a network.

NOTE: At any time during wireless alarm setup, if you have a problem, you can push and hold the Test/Hush

button on any problem unit until you hear three (3) beeps (approx 8 sec), and then release the button. The unit

will reset the unit’s wireless settings (described in Section 7.3). Once wireless settings are reset, the unit will

prompt the user to follow Quickstart instructions.

NOTE: Wireless units will emit a series of LED flashes, tones, and voices as the unit(s) search for a wireless alarm

setup. If you are intending to use wireless units without the wireless function, ignore these notifications, and

the wireless function will eventually turn off. You can turn the wireless function on again at a later date if desired.

See Section 7.2.

NOTE: After activation, the battery can be turned off by turning the switch anti-clockwise. If the alarm is

removed from the mounting plate, the battery will remain active.

Wireless

These models have wireless alarm interconnect capability. When one interconnected unit sounds an alarm, all other

compatible wireless units in the wireless alarm network will alarm. These alarms connect to each other wirelessly

via communication on the 915-928 MHz band.

•A maximum of 24 Quell Safety devices may be interconnected. The interconnect system should not exceed

the following individual limits: 12 smoke alarms and/or 18 alarms total (smoke, CO, Smoke/ CO Combination,

heat, etc.) and/or 6 remote signaling devices and / or relay modules.

•Maximum distance between wireless interconnect models is greater than 100 meters in open air.

COMPATIBLE WIRELESS INTERCONNECT UNITS

DC Models: Q4000DCS-WCB, Q4000DCS-WCL,

Q4000DCS-WBB, Q4000DCS-WBL,

Q4000LDCS-WCH (Safety Light),

Q4000LDCS-WBH (Safety Light)

6. Installation / Mounting Instructions

CAUTION: THIS UNIT IS SEALED INCLUDING THE BATTERY. THE COVER IS NOT REMOVABLE!

Once the steps to setup the wireless alarm network have been completed(See section 7), please proceed to the

following installation steps.

1. To obtain aesthetic alignment of the alarm with the hallway or wall, the “A” line on the mounting bracket should be

parallel with the hallway when ceiling mounting or horizontal when wall mounting.

2. After selecting the proper smoke alarm location as described in Section 6, attach the mounting bracket to the

ceiling as shown in Figure 6-A. For wall mounting see Figure 6-B. Place the mounting plate on the wall; be sure the

“A” line is horizontal (parallel to the floor). Use the screws and anchors provided to secure the mounting bracket (use

3/16” drill bit for anchors).

3. This alarm has a battery permanently sealed inside; No battery installation is necessary.

Align the alarm with the mounting plate and rotate clockwise (right) until the unit stops and clicks into place.

• Install the alarm fully on the mounting bracket by rotating the alarm in a clockwise direction.

NOTE: The alarm will mount to the plate in four (4) positions (every 90 degrees).

The alarm is now activated! After installation/activation, test your alarm as described in Operation and Testing section.

WARNING : FAILURE TO PROPERLY INSTALL AND ACTIVATE THIS ALARM WILL PREVENT PROPER

OPERATION OF THIS ALARM AND WILL PREVENT ITS RESPONSE TO FIRE HAZARDS.

Figures 6-C

Figures 6-B

When mounting

in a hallway, the

“A” line should

be parallel with

the hallway.

Alignment Marks

(”A” Line) on

Mounting

Bracket

When wall

mounting, the

“A” line should

be horizontal.

Remove

Install

Figures 6-A

Otros manuales para Q4000DCS-WCB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Detector de humo de Quell

Quell

Quell Q1400 Manual de usuario

Quell

Quell SA 800 Manual de usuario

Quell

Quell Q10YHL Manual de usuario

Quell

Quell Q945 Manual de usuario

Quell

Quell Q1300 Manual de usuario

Quell

Quell Q4000DCS-WCB Manual de usuario

Quell

Quell Q301 Manual de usuario

Quell

Quell Q1300 Guía del usuario

Quell

Quell Simline QSP10 Manual de usuario

Quell

Quell QC1500 Manual de usuario

Quell

Quell Q2300W Manual de usuario

Quell

Quell Q2300 Manual de usuario

Quell

Quell Q307 Manual de usuario

Quell

Quell QPI9010 Manual de usuario

Quell

Quell Q946 Manual de usuario

Quell

Quell QM10 Manual de usuario

Quell

Quell Q910 Manual de usuario

Quell

Quell Q1400 Manual de usuario

Quell

Quell Q9080 Manual de usuario

Manuales populares de Detector de humo de otras marcas

x-sense

x-sense SD19-W Manual de usuario

BRK electronic

BRK electronic First Alert P1010 Manual de usuario

FireAngel

FireAngel Thermoptek ST-622 Manual de usuario

teko

teko Astra-42A Manual de usuario

Safetec

Safetec SDS-2/6 Manual del propietario

Siemens

Siemens PE-11C Manual de usuario

System Sensor

System Sensor DH500ACDC Manual de usuario

Resolution Products

Resolution Products RE612 CryptiX Manual de usuario

First Alert

First Alert PC900V Manual de usuario

Eminent

Eminent EM6590 E-Domotica Manual de usuario

Ei Electronics

Ei Electronics Ei Ei168RC Manual de usuario

Carrier

Carrier Kidde Quell Q301 Manual de usuario

VESDA

VESDA VLF-500 Manual de usuario

ELRO

ELRO FS8110 Manual de usuario

Heiman

Heiman SMOKI NS-626PHS Manual de usuario

Regin

Regin SDD-S65 Manual de usuario

Family Gard

Family Gard FG225 Manual de usuario

Greystone

Greystone DSD120 Manual de usuario