Quamtum HotSpot HS2 Manual de usuario
User manual
WIRELESS PORTABLE ROUTER (LTE)
We invite you to carefully read this manual before
using it. Please keep it for future refrence.
HotSpot HS2
Quamtum
If you have any questions about the
purchased product, please contact us for
personalized attention.
We appreciate your trust and preference
for purchasing one of our devices, we are
sure that you will obtain great benefits.
2
Limitation of Liability
Quamtum Connectivity de SA de CV, will not be responsible for any loss
of benefits or indirect, special, incidental or consequential damages resulting or
derived from the use of this product, whether or not it was informed, knew or
should have known of the possibility of such damages, including the cost of
installations or substitute products or any cost of downtime.
Copyright © 2023. All rights reserved. No part of this manual may be reproduced
or transmitted in any form or by any means without the prior written consent of
its affiliates. Quamtum Connectivity de SA de CV, reserves the right to
change or modify any information or specification contained in this manual
without prior notice and without any liability.
Due to the nature of wireless communications, data transmission and reception
can never be guaranteed. Data can be delayed, corrupted (ie, have errors), or
lost entirely.
All images shown below are for informational purposes.
3
Legal information
2. Instruction and Operations
2.1
2.2 General specifications
Product diagram
30
5
31
6
6
6
8
8
9
9
10
13
14
16
19
20
21
21
21
22
23
23
24
25
26
27
28
29
29
2.13.1 Access to the WEB administrator
Content
2.3 SIM installation
2.4 Battery charging
2.5 Turn on your HotSpot HS2
2.6 Internet connection
2.7 USB connection
2.8 Battery saving mode
2.9 Restore Factory Settings
2.10 Change SSID and password
2.11 Establish Wireless connection
2.12 Establish WPS connection
2.13 Using the interface
2.13.2 Main screen
2.13.3 Information
2.13.4 Messages
2.13.5 Contacts
1. Know the product
9. Federal Communications Commission (FCC) regulations
2.13.6 Advanced Settings
2.13.7 Quick Settings
3. Battery Care
4. Notes
5. Environmental Protection Statement
6. Applicable Environment
7. Electrical Specifications
8. FAQ
4
1 user manual.
1 Warranty policy.
1 Quick installation guide.
Use only accessories and devices approved by QUAMTUM CONNECTIVITY
DE SA DE CV, otherwise you run the risk of serious effects on
your health, electrical damage to your mobile device, or to the facilities
within your property.
By using accessories not authorized by QUAMTUM CONNECTIVITY DE
SA DE CV you invalidate the guarantee.
1. Get to know the
product The HotSpot HS2 PORTABLE WIRELESS (LTE) ROUTER
is a high-performance, powerful battery and high-speed modem
that's great to take with you wherever you go thanks to its pocket size
and light weight. Offers Wi-Fi connection to multiple devices like tablets,
computers, phones, etc.; To access the Internet, share files and more,
just plug and play.
Package content 1
PORTABLE WIRELESS ROUTER (LTE) HotSpot HS2.
1 USB cable.
5
6
4
6
2
1
5
3
2.2 General Specifications
1. LED Indicators
2. Device Case 3. Power
Button
2. Instruction and Operations
2.1 Product Diagram
4.USB connector
5. WPS Button
6. Device Cover
Description
1
LED indicators
4
Icon
2
3
No.
3. Battery
2. Message
Flashing: New message
Green: Battery over 70% Red: Low
battery Flashing:
Battery is charging
Intermittent
Intermittent
7
1. 4G(LTE) indicator
Intermittent
Green: Connected to the 4G network.
Blue: Connected in data roaming mode. Red: No
signal or
SIM card not recognized.
4. Wi-Fi
Blue: Wi-Fi access point enabled Flashing: WPS
active
Note: 1. Use only chargers compatible with the device and specified by the designated manufacturer.
Using an incompatible charger or one from an unknown manufacturer may cause the HotSpot HS2
PORTABLE WIRELESS (LTE) ROUTER to malfunction, fail, or even cause a fire. Such use voids all
warranties, whether express or implied, on the product. (2) Inside the box you will find the appropriate
USB cable to charge your device. If for some reason you do not have the cable provided by the
manufacturer, it is recommended to use one compatible with the following characteristics:
Output: 5.0Vdc 1A
2.4. Battery charge
Use only a standard SIM card (2FF), do not use 3FF (Micro SIM) or 4FF
(Nano SIM) cards unless you use a 2FF size adapter.
Input: 100-240 Vac 50/60 Hz 150 mA
If your PORTABLE WIRELESS ROUTER (LTE) HotSpot HS2 has not been
used for a long time, or the battery is completely depleted, the device
may not be able to turn on immediately after connecting the charger.
Charge the battery for a while before trying to turn on the equipment.
2.3. SIM Card Installation
8
2. Remove the battery
3. Put the SIM card in the
correct position
Note: Please do not use SIM/USIM cards that do not correspond to the port where the SIM/
USIM card will be placed, such as 3FF (Micro SIM) or 4FF (Nano SIM) cards, otherwise use a
2FF size adapter (Mini SIM)
A compatible SIM card and an active data plan must be used to enjoy internet service.
1. Remove the cover
2FF
9
Where XXXX stands for the last 4 digits of the MAC address.
2. Sign in to enter equipment settings. Default permissions:
The connection parameters have been preset according to the
requirements of the Operator and the PORTABLE WIRELESS ROUTER (LTE)
Web User: Telcel_Admin
And XXXXXXXXX is the hexadecimal password of 10 random digits.
HotSpot HS2 will automatically connect to the Internet.
The device is fully charged in an approximate period of 2-3 hours.
However, it is important to note that it requires a minimum period of 24
hours to be charged for the first time, this will allow you to define a high
charging threshold.
Web Password: TelcelXXXX
Logging in to the web
administration page
2.5. Turn on your HotSpot
HS2 Press and hold the power button until the LED indicators
start to flash.
Connect your HotSpot HS2 PORTABLE WIRELESS (LTE) ROUTER
to a computer via Wi-Fi or USB port. The information to access
the network can be found by removing the cover on the back of the
equipment and removing the battery, there you will find the label
with the default
information: SSID:
Telcel -HS2-XXXX Wi-Fi Password: XXXXXXXXXXX
To enter the web manager it is necessary to follow these steps:
1. Open the browser and enter http://192.168.8.1 in the
address bar.
2.6. Internet connection
Note: You can log in to the web management page and enable or disable auto connect.
Hot Spot HS2
10
Once logged in, you will be able to view your connection status data on
the main screen, configure your Wi-Fi network, manage connected devices,
access your statistics and more. To know more information
regarding your PORTABLE WIRELESS ROUTER (LTE) HotSpot HS2,
locate the Status Information section on the main screen, and you will
find, SIM card number, signal strength, IMSI, IMEI and more.
2.7 USB connection
When you connect your PORTABLE WIRELESS (LTE) ROUTER to the USB
port of your PC for the first time, you must allow the installation program to
run to enable Internet connection. When the first connection is made and
the device is detected by the port, the following dialog will be displayed:
Password: XXXXXXXXX
SSID: Telcel-HS2-XXXX
Tabla de contenidos
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad