Quadra-Fire CLASSIC BAY 1200 Guía de configuración

www.quadrare.com 7014-145 May 9, 2008

CLASSIC BAY 1200 PELLET STOVE & INSERT

Heat Exchanger & Exhaust Cleaning Instructions

Refer to your Owner’s Manual for complete cleaning

instructions for all components.

For trouble free use of your pellet appliance you must perform cleaning

as called for in these instructions. Not doing so will result in:

• Poor operating performance

• Smoke spillage into the home

• Overheating of components

Not properly cleaning your appliance on a regular basis will void your

warranty.

WARNING

Fire Risk

Page  7014-145 May 9, 2008

FIREPOT MAINTENANCE

Pull Cleaning Rod OUT and IN a couple of times to shake

debris loose.

The repot air holes will need to be scraped occasionally

depending on the quality of fuel being used. Use a putty

knife, a at head screwdriver or the repot clean-out tool

provided to remove excess carbon and clinkers from the

repot.

Firepot Cleaning Rod

Firepot Air Holes

PROPER SHUTDOWN PROCEDURE

NOTE: Performing this routine service will require approximately 20

minutes a month depending on type and quality of fuel you burn.

CLEANING OR FREQUENCY DAILY WEEKLY MONTHLY YEARLY

INSPECTION

FIREPOT

Wood Pellets

FIREPOT

Corn

Every 3 bags

Every 1 bag

ASHPAN

Wood Pellets Every 5 bags

HEAT EXCHANGER Every 1 ton of

fuel

-OR-

EXHAUST BLOWER

CONVECTION

BLOWER

Every 3 tons of fuel

or more frequently

depending on fuel

type

ASHPAN

Corn X

-OR-

Daily

Shock and Smoke Hazard

• Turn down thermostat, let appliance completely cool and exhaust

blower must be off. Now you can unplug appliance before servicing.

• Smoke spillage into room can occur if appliance is not cool before un-

plugging.

• Risk of shock if appliance not unplugged before servicing appliance.

CAUTION

Sample of a larger clinker

May 9, 2008 7014-145 Page 

Tools Needed: Shop Vac, Phillips head and at head screwdriver

1200 Pellet Insert

Heat Exchanger

Cleaning Rods

Lift the hopper lid to access the cleaning rods. Both

black bent handle pull rods are located close to the face

of the appliance to the left and right side. Figure 3.1.

Pull the rods straight out until they stop, approximately

0 inches (508mm).

.

To clean, slide the rods OUT and IN a couple of

times.

1. Open the right side access door and then open the

glass door.

. Grasp the bottom of the bafes and pull up to dis-

lodge from hook attachment.

. Use a standard screw driver to unlatch the covers

beneath the bafes of each side.

4. Re-install in reverse order.

B. Remove Bafe to Access Heat Exchanger

Tubes and Firebox Exhaust Exits

A. Cleaning the Heat Exchanger Chambers

Figure 3.1

Left & Right Access Covers

Remove Screws

Exposed Heat Exchanger Tubes

Drop Tube

Figure 3.2 - Bafe Removed

Use a Shop Vac to vacuum any y ash and soot from the

heat exchanger tubes and rebox area. Figure 3.2.

. Remove any debris that may be in the drop tube.

C. Vacuum Heat Exchanger Tubes, Firebox Area

and Drop Tube

D. Clean Firebox Exhaust Exits & Exhaust Blow

There are  exhaust exits at the back of the rebox on

the left and right side. Figure 2.

. Using a Phllips head screwdriver remove the screws

and set aside the access covers.

. Vacuum the  exhaust exits thoroughly.

4. Clean the exhaust blower blades while the access

cover on the left side is still removed. Figure 3.3.

Clean-Out Door

Exhaust Blower

Vent Pipe Adapter

Figure 3.4

Exhaust Blower

Left Access Cover

Figure 3.3

E. Clean Exhaust Exit Behind the Exhaust Blower

1. Open the hinged access door on the left of the insert.

Figure 3.5.

. Reach in and unlatch the clean-out door that is con-

nected to the rear of exhaust blower. Figure 3.4.

. Use a small vacuum hose attachment to clean area.

4. Re-latch and close clean-out door.

Exhaust

Blower

Convection

Blower

Hinged Access Door

Clean-Out

Door

Vent Pipe

Adapter

Firepot

Cleaning Rod

Figure 3.5

Page 4 7014-145 May 9, 2008

Tools Needed: Shop Vac and Phillips head screwdriver

1200 Pellet Stove

Lift the hopper lid to access the cleaning rods. Both

black bent handle pull rods are located close to the face

of the appliance to the left and right side. Figure 4.1.

Pull the rods straight out until they stop, approximately

0 inches (508mm).

.

To clean, slide the rods OUT and IN a couple of

times.

A. Cleaning the Heat Exchanger Chambers

Heat Exchanger Cleaning Rods

Figure 4.1

1. Open the upper right side panel door and then open

the glass door.

. The  bafes are located at the top inside of re-

box.

. Place your hand on the bafe and slide it up and the

bottom edge will fall down and then you can lift the

bafe out. Repeat for the other side.

4. Re-install in reverse order.

B. Remove Bafe to Access Heat Exchanger

Tubes and Firebox Exhaust Exits

Exposed Heat Exchanger Tubes

Drop Tube

Use a Shop Vac to vacuum any y ash and soot from the

heat exchanger tubes and rebox area. Figure 4.2.

. Remove any debris that may be in the drop tube.

C. Vacuum Heat Exchanger Tubes, Firebox Area

and Drop Tube

Figure 4.2

D. Clean Exhaust Exit Behind the Exhaust Blower

1. Open both the upper and lower right side panels.

Figure 4.3.

. Using a Phillips head screwdriver remove the 4 screws

from the clean-out plate and set aside. Figure 4.3.

. Use a small vacuum hose attachment to clean area.

Figure 4.4.

4. Re-attach clean-out plate and close side panels.

Clean-Out Plate Removed

Exhaust Blower

Clean-Out Plate

Remove 4 Screws

Open Right

Side Panels

Figure 4.3

Figure 4.4

Tabla de contenidos

Otros manuales de Estufa de pellets de Quadra-Fire

Quadra-Fire

Quadra-Fire SANTAFE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNINSAE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CB1200-I Pellet Insert CB1200I-B Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire 1000 Gold Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CB1200M-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CASTILEI-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CB1200M-MBK Manual de usuario

Quadra-Fire

Quadra-Fire TREKKER-CSB Manual de usuario

Quadra-Fire

Quadra-Fire TREKKER INSERT series Manual de usuario

Quadra-Fire

Quadra-Fire Santa Fe Pellet Stove Guía de seguridad

Quadra-Fire

Quadra-Fire SANTAFE-B1 Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire SANTAFE-C Manual de usuario

Quadra-Fire

Quadra-Fire CB1200M-MBK Manual del propietario

Quadra-Fire

Quadra-Fire SANTAFE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Manual de usuario

Quadra-Fire

Quadra-Fire MTV-E2-CSB Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire MTVI-E2-MBK-C Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-CSB Manual de usuario

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Manual de usuario

Manuales populares de Estufa de pellets de otras marcas

SMG

SMG Comfort Bilt HP50GC Manual de usuario

Palazzetti

Palazzetti JP Series Guía de instalación

Travis Industries

Travis Industries Avalon 900 PS Manual de usuario

Flame

Flame FP-45 Manual de usuario

Astra

Astra P-7 Manual de usuario

Heatilator

Heatilator ECO-ADV-PS35 Manual de usuario

Cadel

Cadel aquos 24 h2O Manual de usuario

vicenza

vicenza V4.5 Manual de usuario

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Manual técnico

Ferroli

Ferroli GEMMA Manual de usuario

pleasant hearth

pleasant hearth PH35PS Series Manual de usuario

Breckwell

Breckwell Tradition P24FS Manual de usuario

England's Stove Works

England's Stove Works 25-EP Manual de usuario

Avalon

Avalon Astoria Manual de usuario

Spartherm

Spartherm Mellino Guía rápida

United States Stove

United States Stove American Harvest 6039 Manual de usuario

Extraflame

Extraflame DUCHESSA IDRO Manual de usuario

SMG

SMG ComfortBilt HP21 Manual de usuario