Quadra-Fire TREKKER-CSB Manual de usuario

1September 24, 2018

7080-165D

TREKKER FREE STANDING PELLET

APPLIANCE

MODEL(S):

TREKKER-CSB

TREKKER-MBK

TREKKER-PBK

TREKKER-PDB

TREKKER-PFT

TREKKER-PMH

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

Tested and approved for wood pellets only. Burning of

any other type of fuel voids your warranty.

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Consult local building, re o󰀩cials or authorities

having jurisdiction about restrictions, installation

inspection, and permits.

WARNING

If the information in these instructions is

not followed exactly, a re could result

causing property damage, personal

injury, or death.

• Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

• Do not over re - If appliance or chimney connector

glows, you are over ring. Over ring will void your

warranty.

• Comply with all minimum clearances to combustibles

as specied. Failure to comply may cause house re.

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down. Hot glass will

cause burns.

WARNING

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high

temperatures

• High temperatures may ignite clothing or other

ammable materials.

• Keep clothing, furniture, draperies and other

ammable materials away.

NOTE

To obtain a French translation of this manual, please contact

your dealer or visit www.quadrare.com

Pour obtenir une traduction française de ce manuel, s’il vous

plaît contacter votre revendeur ou visitez www.quadrare.com

2September 24, 2018

7080-165D

TREKKER FS

1 Important Safety Information............. 3

A. Appliance Certication........................3

B. BTU & E󰀩ciency Specications ................3

C. Glass Specications .........................4

D. Electrical Rating ............................4

E. Mobile Home Approved .......................4

F. Non-Combustible Materials ....................4

G. Combustible Materials .......................4

H. Sleeping Room .............................4

I. California - Prop65 ...........................4

2 Getting Started .................................... 5

Design, Installation & Location Considerations .........5

B. Tools And Supplies Needed ...................6

C. Inspect Appliance and Components .............6

D. Removal of Appliance from Shipping Materials.....6

E. Install Checklist .............................7

3 Dimensions and Clearances.............. 8

A. Appliance Dimensions ........................8

B. Clearances to Combustibles (US & Canada) .....10

C. Hearth Pad Requirements (UL & ULC) ..........11

D. Alcove ...................................12

4 Vent Information................................ 13

A. Venting Termination Minimum Requirements .....13

B. Avoiding Smoke and Odors...................14

C. Negative Pressure..........................15

D. Draft ....................................15

E. Chimney and Exhaust Connection .............15

F. Equivalent Feet of Pipe ......................16

G. Pipe Selection Chart .......................16

5 Venting Systems ............................... 17

A. Through The Wall ..........................17

B. Vertical into Existing Class A Chimney ..........18

C. Through The Wall & Vertical - Exterior ..........18

D. Vertical - Interior - Typical Installation ...........18

E. Masonry..................................19

F. Alternate Masonry ..........................19

6 Appliance Set-Up .............................. 20

A. Leg Leveling System .......................20

B. Outside Air Kit Instructions ...................20

C. Top Vent Adapter Installation..................21

E. Optional Log Set Placement Instructions ........22

F. Installation of User Interface ..................23

G. Power to Appliance and User Interface..........23

H. Location & Mounting User Interface ............23

7 Mobile Home Installation.................. 24

8 Reference Materials.......................... 25

A. Service and Maintenance Log.................25

B. Accessories List............................27

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

3September 24, 2018 7080-165D

TREKKER FS

1 Important Safety Information

Model Trekker Pellet Appliance

Laboratory OMNI Test Laboratories, Inc.

Report No. 061-S-83-2

Type Solid Fuel Room Appliance, Pellet Fuel

Burning Type

Standard ASTM E1509-12, ULC S627-00 and

(UM) 84-HUD, Mobile Home Approved.

FCC

Complies with Part 15 of FCC Rules.

Operation is subject to the following two

conditions: (1) this device may not cause

harmful interference, and (2) this device

must accept any interference received,

including interference that may cause

undesired operation.

A. Appliance Certication B. BTU & E󰀩ciency Specications

Emissions Report

Number: 0061PS094E

EPA Certication #: 98-17

EPA Certied Emissions: 0.74 g/hr

*LHV Tested E󰀩ciency: 83.2%

**HHV Tested E󰀩ciency: 77.9%

***EPA BTU Output: 12,682 - 39,428 / HR

****BTU Input: 16,396 - 50,775 / HR

Vent Size: 3, 4 or 6 inches, “L” or “PL”

Hopper Capacity: 52 lbs.

Fuel Wood Pellets

* Weighted average LHV e󰀩ciency using data collected

during EPA emissions test.

**Weighted average HHV e󰀩ciency using data collected

during EPA emissions test.

***A range of BTU outputs based on HHV and the burn

rates from the low and high EPA tests.

****Maximum BTU input based on the high burn section

of the EPA emissions test.

This pellet appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate

this pellet appliance in a manner inconsistent with operating instructions in this manual.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the

ASTM E1509-04, ULC S627-00, (UM) 84-HUD and ULC/ORD-C-1482.

This manual describes the installation of the Quadra-Fire, Trekker pellet appliance. This appliance meets the 2020 U.S.

Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2020. Under specic test

conditions this appliance has been shown to deliver heat at rates ranging from 12,682 to 39,428 Btu/hr.

4September 24, 2018

7080-165D

TREKKER FS

C. Glass Specications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please

contact your dealer for replacement glass.

D. Electrical Rating

115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps

E. Mobile Home Approved

• This appliance is approved for mobile home

installations when not installed in a sleeping room and

when an outside combustion air inlet is provided.

• The structural integrity of the mobile home oor, ceiling,

and walls must be maintained.

• The appliance must be properly grounded to the frame

of the mobile home and use only Listed pellet vent

Class “L” or “PL” connector pipe.

• Outside Air Kit, part OAK-3 must be installed in a

mobile home installation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualied

installer, service agency or your dealer.

H. Sleeping Room

When installed in a sleeping room it is recommended that

3ft of vertical be installed prior to horizontally exiting the

room and a smoke/CO alarm be installed in the bedroom.

The size of the room must be at least 50ft³ per 1,000 Btu/hr

stove input, if the stove exceeds the room size, out air must

be installed.

I. California - Prop65

WARNING

This product and the fuels used to operate this product (wood), and

the products of combustion of such fuels, can expose you to

chemicals including carbon black, which is known to the State of

California to cause cancer, and carbon monoxide, which is known to

the State of California to cause birth defects or other reproductive

harm. For more information go to: WWW.P65Warnings.ca.gov

F. Non-Combustible Materials

G. Combustible Materials

Material made of/or surfaced with any of the following

materials:

- Wood

- Compressed Paper

- Plant Fibers

- Plastic

- Plywood/OSB

- Sheet Rock (drywall)

Any material that can ignite and burn: ame proofed or not,

plastered or non-plastered.

NOTE: Hearth & Home Technologies, manufacturer

of this appliance, reserves the right to alter its

products, their specications and/or price without

notice.

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all

components.

• Operating appliance without legs attached (if

supplied with appliance).

• Do NOT Over re - If appliance or chimney connector

glows, you are over ring.

Any such action that may cause a re hazard.

WARNING

Fire Risk

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided

by, the following actions:

Material which will not ignite and burn, composed of any

combination of the following:

-Steel

- Plaster

-Brick

-Iron

-Concrete

-Tile

-Glass

-Slate

Materials reported as passing ASTM E 136, Standard Test

Method for Behavior of Metals, in a Vertical Tube Furnace

of 750° C.

5September 24, 2018 7080-165D

TREKKER FS

Install Guide

2 Getting Started

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended:

Outside Air Intake

on windward side

NOT recommended:

Outside Air Intake

on leeward side

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Figure 5.1

Design, Installation & Location Considerations

1. Appliance Location

Since pellet exhaust can contain ash, soot or sparks, you

must consider the location of:

• Windows

• Air Intakes

• Air Conditioner

• Overhang, so󰀩ts, porch roofs, adjacent walls

• Landscaping, vegetation

• Horizontal or vertical vent termination

2. Floor Support

The supporting oor under the appliance must be able to

handle the weight of the appliance, fuel load and the weight

of the chimney.

Ensure that your oor will support these weights prior to

installation. Add su󰀩cient additional support to meet this

weight requirement prior to installation. The weight of the

appliance is 426 lbs. with a full load of fuel the max weight

is 473 lbs.

NOTICE: Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector,

re o󰀩cials or authorities having jurisdiction over

restrictions, installation inspection and permits.

It is a good idea to plan your installation on paper, using

exact measurements for clearances and oor protection,

before actually beginning the installation. Location of the

appliance and chimney will a󰀨ect performance.

Consideration must be given to:

• Safety, convenience, tra󰀩c ow

• Placement of the chimney and chimney connector and

to minimize the use of chimney o󰀨sets.

• Place the appliance where there will be a clear

passage for a Listed chimney through the ceiling and

roof (vertical) or through exterior wall (horizontal).

• Installing the required outside air kit will a󰀨ect the

location of the vent termination.

When locating vent and venting termination, the ideal

location is to vent above roof line when possible. This

minimizes the a󰀨ects of wind loading.

WARNING

Risk of Fire.

Damaged parts could impair safe operation. Do NOT

install damaged, incomplete or substitute components.

6September 24, 2018

7080-165D

TREKKER FS

B. Tools And Supplies Needed

C. Inspect Appliance and Components

• Open the appliance and remove all the parts and

articles packed inside the Component Pack. Inspect all

the parts and glass for shipping damage.

• Report to your dealer any parts damaged in shipment.

• All labels have been removed from the glass door.

• Plated surfaces have been wiped clean with a soft

cloth, if applicable.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benet.

• Follow pipe manufacturer instructions for

installation and air clearance requirements.

Figure 6.1

Figure 6.2

D. Removal of Appliance from Shipping

Materials

1. Remove box and 2x4 structural boards being careful

not to damage product.

2. Using 3/8 socket or wrench remove both front bolts

from pallet mount brackets. Front pallet mount brackets

will slide outwards away from appliance (Figure 6.1).

3. Using 3/8 socket or wrench remove bolts from side

pallet mount brackets. Side pallet mount brackets will

slide downwards from appliance (Figure 6.2).

4. Carefully pull appliance o󰀨 of pallet and put in desired

location following Hearth Pad and Clearance to

Combustibles on pages 8 & 9.

Tools and building supplies normally required for

installation, unless installing into an existing masonry

replace:

• Reciprocating Saw

• Channel Locks

• Hammer

• Phillips Screwdriver

• Tape Measure

• Plumb Line

• 1/4” Self-Tapping Screws

• Framing Material

• Hi-temp Caulking Material

• Gloves

• Safety Glasses

• Framing Square

• Electric Drill & Bits (1/4”)

• Level

May also need:

Vent Support Straps

Venting Paint

Risk of Fire!

• Damaged parts could impair safe operation.

• Do NOT install damaged, incomplete or

substitute components.

WARNING

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all

components.

• Operating appliance without legs attached (if supplied

with appliance).

• Do NOT Over re

Or any such action that may cause a re hazard.

7September 24, 2018 7080-165D

TREKKER FS

YES IF NO, WHY?

Verified clearance to combustibles.

Appliance is leveled and connector is secured to appliance.

Hearth extension size/height decided.

Outside air kit installed.

Floor protection requirements have been met.

If appliance is connected to a masonry chimney, it should be cleaned and

inspected by a professional. If installed to a factory built metal chimney, the

chimney must be installed according to the manufacturer’s instructions and

clearances.

Appliance Install

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney meets recommended height requirements (5 feet minimum vertical).

Roof flashing installed and sealed.

Terminations installed and sealed.

Venting/Chimney

Clearances

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Floor protection and heart extensions installed per manual requirements.

Appliance Setup

All protective materials removed.

All labels have been removed from the door.

All packaging materials are removed from inside/under appliance.

Manual bag and all of its contents are removed from inside/under the appliance

and given to the party responsible for use and operation.

WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead to a fire or

explosion.

Hearth & Home Technologies recommends the following:

Photographing the installation and copying this checklist for your file.

That this checklist remain visible at all times on the appliance until the installation is complete.

Electrical

120 VAC unswitched power provided to the appliance.

Check outlet with multi-meter for proper polarity and voltage (115-120 VAC).

Record voltage reading: _____________

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.

Customer:

Date Installed:

Lot/Address:

Location of Appliance:

Installer:

Dealer/Distributor Phone Number:

Serial Number:

Model Name:

__________________________________________________________________________

______________________________________________________________________

_______________________________________________________________________

________________________________________________________________

___________________________________________________________________________

________________________________________________________

______________________________________________________________________

_______________________________________________________________________

Started appliance and verified that all motors and blowers operate as they should.

Checked draft using a Manometer. Record readings: ______________________

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, ets.) and corrective action needed:

Comments communicated to party responsible __________________________ by ______________________ on ____________

(Builder/Gen. Contractor) (Installer) (Date)

Checked vacuum using a Manometer. Record readings: ____________________

E. Install Checklist

8September 24, 2018

7080-165D

TREKKER FS

Figure 8.1 - Top View Figure 8.4 - Top View with Top Vent Adapter (TPVNT-3) and

O󰀨set Adapter (812-3570).

3-5/8 in

(93mm)

3-5/8 in

(93mm)

10-3/8 in

(264mm)

10-3/8 in

(264mm)

3-3/4 in

(97mm)

4-1/8 in

(104mm)

6-1/8 in

(155mm)

6-1/8 in

(155mm)

14 in (357mm)

5-13/16 in

(147mm)

2-9/16 in

(65mm)

3-13/16 in

(97mm)

14-1/16 in

(357mm)

Figure 8.2 - Top View with Top Vent Adapter (TPVNT-3) and

O󰀨set Adapter (811-0720).

Figure 8.5 - Top View with Top Vent Adapter (TPVNT-6) and

O󰀨set Adapter (811-0720).

3-3/4 in

(97mm)

3-3/4 in

(97mm)

4-1/8 in

(104mm)

4-1/8 in

(104mm)

8-1/4 in

(208mm)

8-1/4 in

(208mm)

10-3/8 in

(264mm)

10-3/8 in

(264mm)

Figure 8.3 - Front View

28-1/8 in (714mm)

32 in

(813mm)

11-3/4 in

(297mm)

18-1/2 in (469mm)

28-7/16 in (722mm)

3 Dimensions and Clearances

A. Appliance Dimensions

9September 24, 2018 7080-165D

TREKKER FS

31-1/16 in

(788mm)

29-3/16 in

(741mm)

Figure 9.1 -Side View

Figure 9.2 - Side View with Top Vent Adapter (TPVNT-3) and

O󰀨set Adapter (812-3570).

25-3/8 in

(646mm)

25-3/8 in

(646mm)

27-1/8 in

(688mm)

27-1/8 in

(688mm)

Figure 9.4 - Side View with Top Vent Adapter (TPVNT-6) and

O󰀨set Adapter (811-0720).

29 in

(738mm)

29 in

(738mm)

30-5/8 in

(779mm)

30-5/8 in

(779mm)

Figure 9.3 - Side View with Top Vent Adapter (TPVNT-3) and

O󰀨set Adapter (811-0720).

28-3/4 in (730mm)

26-7/8 in (683mm)

19-9/16 in

(497mm)

20 in (508mm)

10 September 24, 2018

7080-165D

TREKKER FS

Installations with:

TPVNT-3 Top Vent Adapter with Heat Shield and

Clean-out

TPVNT-6 Top Vent Adapter with Clean-out

811-0720 (3” to 4”) O󰀨set Adapter

812-3570 (3” to 6”) O󰀨set Adapter

B. Clearances to Combustibles (US & Canada)

NOTE:

• Illustrations reect typical installations and are FOR

DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design

preference.

Horizontal Through the Wall Inches Millimeters

ABack Wall to Appliance 2 51

BSide Wall to Appliance 6 152

Corner Installation Inches Millimeters

CWalls to Appliance 251

Vertical Installation Inches Millimeters

DBack Wall to Flue Pipe 376

ESide Wall to Appliance 6 152

FBack Wall to Appliance 8 203

Corner Installation Inches Millimeters

GSide Wall to Flue Pipe 376

Otros manuales para TREKKER-CSB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Estufa de pellets de Quadra-Fire

Quadra-Fire

Quadra-Fire CB1200-B Manual de usuario

Quadra-Fire

Quadra-Fire SANTAFE-B1 Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire MTVERNINSAE-PMH Manual de usuario

Quadra-Fire

Quadra-Fire SANTAFE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire SANTAFE-C Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Manual de usuario

Quadra-Fire

Quadra-Fire CB1200M-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire TREKKERI-MBK Manual de usuario

Quadra-Fire

Quadra-Fire SANTAFE-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire CASTILEI-MBK Guía de seguridad

Quadra-Fire

Quadra-Fire CASTILEI-MBK Manual de usuario

Quadra-Fire

Quadra-Fire CASTILEI-MBK Manual de usuario

Quadra-Fire

Quadra-Fire SANTAFEI-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-CSB Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-MBK Manual de usuario

Quadra-Fire

Quadra-Fire MTVERNON-AE-CSB Manual de usuario

Quadra-Fire

Quadra-Fire CASTILE-MBK-B Manual de usuario

Quadra-Fire

Quadra-Fire MT. VERNON E2 Series Manual de usuario

Quadra-Fire

Quadra-Fire CB1200M-MBK Manual del propietario

Quadra-Fire

Quadra-Fire CASTILE-CWL-B Manual de usuario

Quadra-Fire

Quadra-Fire MTV-E2-CSB Manual de usuario

Manuales populares de Estufa de pellets de otras marcas

SMG

SMG Comfort Bilt HP50GC Manual de usuario

Palazzetti

Palazzetti JP Series Guía de instalación

Travis Industries

Travis Industries Avalon 900 PS Manual de usuario

Flame

Flame FP-45 Manual de usuario

Astra

Astra P-7 Manual de usuario

Heatilator

Heatilator ECO-ADV-PS35 Manual de usuario

Cadel

Cadel aquos 24 h2O Manual de usuario

vicenza

vicenza V4.5 Manual de usuario

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Manual técnico

Ferroli

Ferroli GEMMA Manual de usuario

pleasant hearth

pleasant hearth PH35PS Series Manual de usuario

Breckwell

Breckwell Tradition P24FS Manual de usuario

England's Stove Works

England's Stove Works 25-EP Manual de usuario

Avalon

Avalon Astoria Manual de usuario

Spartherm

Spartherm Mellino Guía rápida

United States Stove

United States Stove American Harvest 6039 Manual de usuario

Extraflame

Extraflame DUCHESSA IDRO Manual de usuario

SMG

SMG ComfortBilt HP21 Manual de usuario