Pyle PDLB372 Manual de usuario

-8- Important: If don't understand about right install ways,

please consult to normal installing specialist.

Important:

Thank you for choosing our productsThank you for choosing our products

INSTALLATION GUIDE

Item No.:PDLB372Item No.:PDLB372

TV Size Range:10 24""~

Max load capacity 15Kg/33lbs

Integrated Cable management

Angle Adjustable

Desktop Bracket

www pyleaudio com..

MADE IN CHINA

Pyle Audio

1600 63rd st , Brooklyn, NY, 11204

(718)236-8000

-2- -7-

Parts:

Caution The turning

angleisnottoolarge.

Or it may result in

personal injury or

product damage.

Caution:

2 Adjusted with the arms.

With circumvolve the arms, TV can turning to two sides of the base

support until touch the vertical tube. First joint adjusting angle is ±90°,

second is ±90°,third is ±135° .

Use to adjust the degree

of those joints.

Wrench

Display Adjustments

Roll Control

Function -Horizontal leveling of the display.

Operation -Grasp the sides of the display, and roll it into the desired

position. Then adjusting Roll Tension .

Display Adjustments

Roll Control

Angle adjusting

1 Adjusted with the TV plate .

With circumvolve the wall Plate ,TV can adjust in the direction of left

right up and down Vertical Adjusting Angle is from 5° to 20°.

Level Adjusting Angle is 20°

,. -

Angle adjusting

Has correctional function: f the wall plate were

installed imbalance, you can adjust the TV plate

he assembly. Adjust angle is 10

to lever off t °.

Fig 7

-520°~ °

20°

±°90

ABCDE

±135°

Vertical height adjustment

0~110mm vertical height adjustment.

ou can adjust the arm assembly up without any other action, but before

you lower the arm assembly, you should push the plastic button first.

Vertical height adjustment

Hardware List:

ID Description

Base

TV Plate

Arm Assembly

Tube Cover

5x5mm Wrench

4x4mm Wrench

M4×8mm bolt

M ×12mm4 bolt

M ×8mm5 bolt

M5×12mm bolt

M5 washer

Qty

Choose the desired angle and turn clockwise the Tension Knob on the right

of the arm.

±°90

Plastic

button

Tension Knob

-6- -3-

Choose fitting position on the desk.

The thinkness of the table should be smaller than 55mm

Base

Choose the position that the Base you want installed.

Important: Make sure there is enough space to spread display, considering

the show size.

Step1

Step2 Attach

Choose fitting position on the desk.Step1

Step2 Attach Base

Step 6 Using Cable Management

The mount include a cable management function, where cables can be

routed along the length of the arm assembly.

To install cables, you’ll first need to remove the cable covers and set all

parts aside.

Step 6Using Cable Management

Cable cover

Fig 5

Route the cables along one side of the Inner Arm (nearest the wall plate).

With cables in place, loosely secure the Inner Arm cable covers back in place.

Next, route the cables along the opposite side of the Outer Arm. Be sure to

leave slack in the cable where it transitions between two sides of the Arm

Assembly. With cables in position, loosely secure the Outer Arm cable

covers back in place.

For best system performance, route the AC power cable separately

from the signal cables.

With all cables in place, pull the display in and out and check that the

arm assembly moves freely, without stretching or damaging the cables,

andthensecurethecablecovers.

DO NOT use a hex wrench on the cable covers, only apply

pressure with your finger.

Note:

Important:

Note:

Important:

WARNING

We are not responsible for any personal injury or

product damage due to mishandling, incorrect

mounting, incorrect assembly or incorrect use of

this product.

Fig 1

Fig 6

-4- -5-

Caution : This Product LCD /Plasma

Wall Mount Bracket is intended for use only

with the maximum weights indicated .See

apparatus instructions .Use with products

heavier than the maximum weights indicated

instability causing possible injury .

Caution :

Fig 3

According LCD hole's size, deep, position to choose bolts. Using chose

bolts(A-D) and washers(E) to install the LCD on the panel. As shown

in Fig3.

Don't force the bolt to LCD hole,

avoiding damage to people and instrument.

Don't use electronics drill to fasten screw

Installing the LCD

Carefully:

Step4 Installing the LCD

Carefully: A-D

TV Plate

Warning: Some TV require two people

to lift, as we are not responsible for any

personal injury or product damage due

to mishandling.

Warning:

Step5 Hang the display

Firstly lift up the TV plate installed the LCD, making the trough on the

arm fit to the trough on it ,according trough to embed the TV plate into

the wall plate.

Step5 Hang the display

Step 3

Remove the Tube Cover. Push the Plastic Button down and assemble the Arm.

Adjust the arm assembly to the height then free the Plastic Button.

Recover the tube cover.

desired

Arm AssembleStep 3Arm Assemble

Fig 4

Tighten bolt

Fig 2

Plastic Buttom

Arm

Once the TV is positioned in place,

fasten the Tighten Bolts on Receiving

Joint clockwise to secure the display

to the Arm Assembly.

Otros manuales de Soporte de TV de Pyle

Manuales populares de Soporte de TV de otras marcas

Ergotron

Ergotron Neo Flex Cantilever UHD Manual de usuario

StarTech.com

StarTech.com FPCEILBTB Manual de usuario

VonHaus

VonHaus 05/038 Manual de usuario

Techlink

Techlink ECHO TV Manual de usuario

Sandstrom

Sandstrom SSTVMC12X Manual de usuario

Sony

Sony SU-WL700 Guía

ICW

ICW SCACC18 Manual de usuario

LG WM-L640V Manual de usuario

Gembird

Gembird WM-65ST-01 Manual de usuario

ERARD

ERARD FiTUP XXL 035320 Manual de usuario

PEERLESS

PEERLESS PLCK-1 Guía

Kanto

Kanto RCF180 Manual de usuario

GEM

GEM GEM GP001 Manual de usuario

Gladiator Joe

Gladiator Joe GJ0A0053 Manual de usuario

Vivotek

Vivotek AM-105 Manual de usuario

Vivo

Vivo VESA STAND-VAD1B Manual de usuario

AmazonBasics

AmazonBasics B07QG3LMG4 Manual de usuario

Secura

Secura QLF210 Manual de usuario