Psiber WireXpert Instrucciones de funcionamiento y mantenimiento
Kit Contents
A pair of Multi-mode adapters with source wavelengths of 850nm
1300 nm
A pair of SC-SC duplex reference cords 50/125 um (2 m)
A pair of mandrels for 50/125 um Fiber
Multi-mode Adapter Kit (WX_AD_MM2)
Kit Contents
A pair of Single-mode adapters with source wavelengths of
1310 nm/1550 nm
A pair of SC-SC duplex reference cords 9/125 um (2m)
Single-mode Adapter Kit (WX_AD_SM2)
WireXpert Optical Loss Test kit
Quick Start Guide
Performing AutoTest
To perform an autotest hit on the Autotest button. The test will
automatically start,if the test setting match the conguration of set
reference stored. If the reference setting does not exist, it will prompt you
to perform set reference.
Viewing Results
Once the autotest is complete the summary results are
displayed on the device both local and remote. Click on the wavelength
to see its detailed results.
Exporting Test Results
For exporting Fiber test results stored in the device a USB ash drive is
required. When the ash drive is inserted into WireXpert the screen will
pop-up. Click on the copy Test Records to USB ash drive option and the
test results are automatically copied.
Once the results are copied on to the USB ash drive, plug the ash
drive into a PC and open the ReportXpert application. Import the Fiber
results into the ReportXpert application from the USB ash drive.
Once imported, the test results can be viewed on the PC.
PDF reports can be generated along with the copper test
results using the ReportXpert software.
Most of the standards like TIA 942-A have now removed the maximum
length requirement on the link. However, WireXpert allows you to
congure the length limit to determine the PASS/FAIL criteria of an autotest.
Set it to a big number should you feel the limit unnecessary.
The WireXpert optical testing solution is available for single-mode and
multi-mode certication as sepearate kits. The Single-mode kit allows
Tier1 certication on two wavelengths simultaneously, at 1310nm and
1550nm. Multi-mode performs Tier1 certication at 850nm and 1300 nm.
The kit ships with the adapters and reference cords for launch and
tail cords. The Multi-mode kit ships with a pair of mandrels. Encircled
Flux mode conditioners are available as an orderable option.
For support please contact our partners where you purchased the
equipment from. You can also reach the nearest Psiber oce.
Oce Locations:
Asia Pacic :
Psiber Data Pte Ltd. Singapore
Europe:
Psiber Data GmbH, Krailling, Germany
Psiber Data Ltd, FayGate West Sussex, United Kingdom
Psiber Italy, Monza(MI)
North America:
Psiber Data Systems Inc, San Diego
Single-Mode Adapter Kit Multi-Mode Adapter Kit
Support
1
56
The Single-mode and Multi-mode adapters come
with two ports one for Receive and one for
Transmit. They are marked appropriately on
the top of the adapter.
23 4
Conguration for Set Reference Remote Loopback or Remote Unit Conguration
Setting Reference
Limit and Connectors Setting
WireXpert supports all congurations specied in TIA and
ISO standards for Fiber certication. You can congure Set Reference
from the SETUP menu and under Test Settings tab. Select Single-Direction
or Bi-Directional setting for the autotest. Followed by selection of
loopback or remote unit, and the type of reference(one-jumper,
two-jumper, three-jumper). For details of one-jumper, two-jumper
and three-jumper methods, please refer to users manual.
Single Directional and Bi-Directional Testing
Local Unit Remote Unit
Tx Rx Tx Rx
Single Directional Test
Fiber1
Local to Remote Loss
Local to Remote Loss
Fiber2
Remote to Local Loss
Fiber1
Fiber2
Local Unit Remote Unit
Tx Rx Tx Rx
Bi-Directional Test
Remote Loopback Remote Unit
Local to Remote Loss
Remote to Local Loss
Local to Remote Loss
Remote to Local Loss
Choose Single Direction unless you have a specic need to perform
bi-directional testing. In a single Directional measurement, the loss in
each ber is measured in one direction only. As shown in the gure
above, the loss is measured only from Local to Remote on Fiber1
and Remote to Local direction in Fiber2.
In the case of a Bi-Directional measurement, the loss in each Fiber is
measured in both directions from Local and Remote units. This test
requires you to swap the ber connections in the middle of autotest.
Please don’t swap connections for Setting Reference, just continue both
the steps retaining the connections.
Before performing autotest, the appropriate limits need to be selected for
testing. If either TIA or ISO limits are selected the PASS/FAIL criteria is
determined by the loss limit specied in the standard. In the case of TIA it is
TIA 568 C.3 and if it is ISO, it is ISO 14763-3 standard.
Link Validation limit allows you to set end-end loss irrespective of the
conguration such as number of connectors or splices. The test result
is determined by the customized loss value congured.
Congure the number of splices and connectors in the link under test.
In the case of a TIA/ISO limit selection, the limit is calculated based on the
congured number of connectors and splices. Please exclude the
connectors in Set Reference.The maximum allowable loss for a connector
is 0.75 dB according to both the standards. Nevertheless,WireXpert allows
you to set more stringent standards for connector loss should you require.
This conguration allows selection between loopback testing or using
remote unit to perform autotest. In the case of loopback setting, connect a
short patch cord at the remote end to provide the loopback.
After setting up the conguring set reference, perform setting reference
from the TOOLS menu and clicking on SetReference button.
Use a Reference cord shipped with the kit to perform Reference setting.
The length and loss of the reference cord determine the quality of reference
set.
Local Unit
Tx Rx
Local Unit Remote Unit
Tx Rx Tx Rx
Note 1: WireXpert prompts an error during autotest if the reference setting
for the corresponding conguration is not performed before running the
autotest.
Note 2: WireXpert also veries the quality of reference setting and will warn you
and not allow to complete reference setting if it detects high loss or long patch
cords. Always use the reference cords shipped with the kit.
Length Limit
Otros manuales de Instrumento de medición de Psiber
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario