Psiber Data Systems NetXpert 1400 Manual de usuario
Psiber Data GmbH a Softing Company www.psiberdata.com
Cable Qualifier
User Manual
1400
Net
✗
pert
2
Introduction........................................................................................................3
Kit Contents........................................................................................................4
Safety Information. ...........................................................................................5
NetXpert 1400 Description...............................................................................6
Active Remote Description..............................................................................7
NetXpert 1400 Touch Screen and Buttons. ..................................................8
General Operations...........................................................................................9
System Settings...............................................................................................10
First System Settings Screen (IP Setup)..................................................... 10
Second System Settings Screen (Display Settings). ................................11
Third System Settings Screen (Time and Date).........................................12
Fourth System Settings Screen (Timeout Settings) ..................................12
Fifth System Settings Screen (User Information)...................................... 13
Sixth System Settings Screen (Firmware).................................................. 14
Seventh System Settings Screen (Firmware/Hardware versions).........17
Active Remote .................................................................................................18
Cable Test.........................................................................................................19
Cable Test Overview.......................................................................................20
Cable Test Setup............................................................................................. 21
Cable Type........................................................................................................22
New Cable Type......................................................................................... 22
Edit Existing Cable Type............................................................................22
Select Cable Type...................................................................................... 23
Cable Name.................................................................................................23
Ethernet Cable Test ................................................................................... 23
Cable Faults......................................................................................................24
Saving Cable Tests as PDF............................................................................25
Saving a PDF Report.......................................................................................25
Saving Test List as CSV..................................................................................25
Create a new Test List...................................................................................26
File Manager................................................................................................ 26
Link Test............................................................................................................27
Port Discovery................................................................................................. 27
POE Test ...........................................................................................................27
Tone...................................................................................................................27
Link Light...........................................................................................................28
TABLE OF CONTENTS
Cable Qualifier
1400
Net
✗
pert
3
Network Test ...................................................................................................29
Link Test...........................................................................................................29
DHCP................................................................................................................ 29
Ping Test.......................................................................................................... 30
Trace Route.....................................................................................................30
VLAN ................................................................................................................31
Discovery Protocols ......................................................................................32
File Manager.................................................................................................... 33
USB Mode........................................................................................................ 33
Icon Glossary................................................................................................... 35
Customer service............................................................................................ 36
Maintenance....................................................................................................37
Specifications..................................................................................................38
Warranty Information.....................................................................................39
INTRODUCTION
The NetXpert 1400 Ethernet Speed Certifier offers a complete solution to
test copper cables. The NetXpert 1400 performs speed certification to test
the data-carrying capabilities of electrical Ethernet network cable up to 1
Gb/s by testing for noise in the network, detecting faults in the cable wiring,
and ensuring that cables are able to support the speed capabilities of active
equipment.
To certify Ethernet speed performance of copper cable runs, the NetXpert
1400 handheld tester conducts Bit Error Rate (BER) tests by sending data
packets down specified cable runs at defined data rates to check for errors at
the maximum throughput of the link. The NetXpert 1400 also reports on signal
quality that can impact high-speed data transmission by measuring signal
to noise ratio (SNR). Skew measurements report on the signal time delay
between pairs that can impact Ethernet data transmission. The NetXpert
1400 also provides continuity testing that detects opens, shorts, miswires,
split pairs, reversals, and high-resistance faults while accurately measuring
distance to faults and total cable length.
The NetXpert 1400 includes a comprehensive set of features for testing
active network capabilities: measure Power over Ethernet (PoE) to ensure
the correct power is available on the correct pins, use Port Discovery to
ensure the correct speed and duplex capability are available; connect
at Gigabit Ethernet and run Ping tests to verify connectivity to IP hosts;
discover network devices using Cisco Discovery Protocol (CDP) or Link Layer
Discovery Protocol (LLDP); VLAN discovery; Trace Route function displays the
path internet packets travel to reach a specified destination. The NetXpert
1400 also saves test reports and exports to PCs.
4
Part Number Description
226605 ▪NetXpert 1400
▪NetXpert 1400 main unit
▪Active remote
▪Power supply (2)
▪Network test cables (2)
▪Sacrificial cables (2)
▪4 GB SD card
▪Micro USB cable
▪Network and coax remote set: #1-5,
F-connector coupler (includes foam holder)
▪Hanging strap and clip (2)
▪Large Carrying bag
NetXpert 1400
The NetXpert 1400 comes in one kit that will cover all your needs.
5
Notification Definition
Warning/caution: potential for personal injury or
damage to equipment
Voltage! Warning: hazards could cause harm or death
Conformité Européenne. Conforms to European
Economic Area directives.
Disposal information
!Warning! To avoid possible fire, electric shock,
or personal injury:
• Do not open the case; no user-serviceable parts are inside.
• Do not modify the tester.
• Do not use the tester if it is damaged. Inspect the tester before
use.
• The tester is not intended to be connected to active telephone
inputs, systems, or equipment, including ISDN devices. Prolonged
exposure to the voltages applied by these interfaces may damage
the tester.
• The Lithium Ion battery pack should be serviced by qualied
personnel. Only the original battery pack type should be used
with this product.
!
Safety Information
To ensure safe operations of the NetXpert 1400, follow instructions
carefully and observe warning and caution messages in this
manual. Failure to observe warnings can result in severe injury or
death and can damage the equipment.
6
NetXpert 1400 Description
Modular cable
interface
LCD Touch screen
RJ45 Jack and
F-connector
Kickstand
Battery Door
Menu buttons
Power button
D/C Charger plug
Micro USB and
SD card slot
7
Battery charge
status LED’s Linked/Pass/Fail
LED’s
Active Remote
Status
button
RJ45 Jack
Hook strap loop
D/C Charger plug
Battery Door
Battery door screws
8
Touch an icon to select an option
Touch and drag a list to scroll up or down or touch the Up/Down arrows.
The NetXpert 1400 buttons assist with Navigation,
starting and stopping a test.
Settings Home Back Test
Settings - The Settings button will display the settings menu.
Pressing the settings while in the settings menu will display
additional menu screens.
Home - The Home button will display the home screen from any
menu.
Back - The Back button will display the previous screen.
Test - The Test button will start/stop a test.
NetXpert 1400 Buttons and Touch Screen
The NetXpert 1400 features buttons and a full color capacitive
touch screen to allow easy navigation.
9
On/Off
• Turn NetXpert 1400 on by pressing the Power button .
• Tap the Power button to put the NetXpert 1400 in sleep mode.
• Press and hold the Power button to power the unit off.
Automatic Power Down
The NetXpert 1400 automatically enters sleep mode to conserve
battery power if no input or activity is performed on the device. See
System Settings on page 11 to adjust the length of time before the
automatic power down occurs.
NetXpert 1400 Active Remote
• Check the Active Remote battery status and last test result by
pressing the Status button.
GENERAL OPERATIONS
10
The NetXpert 1400 Setup consists of seven screens to configure
the unit to the user’s preference. Use the Settings button to
navigate through the settings screens.
First System Settings Screen: IPV4 Setup
In the IPV4 setup screen, the NetXpert 1400’s network tests can be
configured to use DHCP or a Static IP addresses. The NetXpert 1400
can also be set to use a DHCP provided DNS or a fixed DNS IP.
• Turn the NetXpert 1400 on by pressing the Power button .
• Touch System Settings on the home screen.
• “Use DHCP” is set as default. To enter static IP’s touch “Use
Static IP” and enter the following:
- Touch “Set IP” and enter the NetXpert 1400 IP address using
the numeric keypad, then touch OK.
- Touch “Set Subnet Mask” and enter the Subnet Mask IP
address using the numeric keypad, then touch OK.
- Touch “Set Gateway” and enter the Gateway IP address,
then touch OK.
• Use “DHCP DNS” is set as default. To manually enter DNS
addresses, touch “Choose DNS”.
• Touch “Set DNS” and use the numeric keypad to enter a
preferred DNS IP address and touch OK.
SYSTEM SETTINGS
Tabla de contenidos
Otros manuales de Instrumento de medición de Psiber Data Systems
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario