PSC Vs1200 Manual de usuario

VS1200

Universal-Wedge

Quick Start Programming

Guide

HS1250

Duet

VS1200/HS1250/Duet Scanners

PSC Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402-9120

Telephone: (541) 683-5700

Toll Free: (800) 547-2507

Telefax: (541) 686-1702

PSC and the PSC logo are registered trademarks of PSC INC.

VS1200, HS1250 and Duet are trademarks of PSC INC.

proceduresdescribedthereinmaybereproducedortransmittedinanyform

or by any means without the prior written permission of PSC Inc. Owner's

ofPSCInc.'sproductsareherebygrantedanon-exclusive,revocablelicense

to reproduce and transmit this documentation for the purchaser's own

internal business purposes. Purchaser shall not remove or alter any

proprietary notices, including copyright notices, contained on this docu-

mentation and shall ensure all such notices appear on any reproductions of

the documentation.

Disclaimer

Reasonable measures have been taken to ensure that all

information contained in this manual is complete and accu-

rate. However, PSC reserves the right to change any specifi-

cation at any time without prior notice.

Table of Content

INTRODUCTION................................................... 1

MANUAL OVERVIEW ............................................................. 2

HOW TO USE THIS MANUAL ........................................... 3

WEDGE PROGRAMING MODE OVERVIEW ................................... 4

SCANNER PROGRAMMING MODE OVERVIEW ............................... 5

SECTION – 1 KEYBOARD-WEDGE PROGRAMMING ................. 7

INTRODUCTION .................................................................... 8

COMMUNICATION CABLE ................................................. 8

CLONNING MODE ....................................................... 10

KEYBOARD-WEDGE COMMUNICATIONS MODES.......................... 13

KEYBOARD-WEDGE PROGRAMMING ................................ 13

RS-232 INTERFACE CONFIGURATION .............................. 31

SECTION– 2 SCANNER PROGRAMMING MODE .................... 49

INTRODUCTION .................................................................. 50

PROGRAMMING YOUR SCANNER ............................................ 51

SCANNER PROGRAMMING MODE ........................................... 52

RETURN TO FACTORY SETTINGS ..................................... 53

PROGRAMMABLE SPEAKER FEATURES .............................. 55

LABEL TRANSMIT FORMAT CONFIGURATION ITEMS .............. 59

SETTING LABEL I.D. ................................................... 60

UPC OPTIONS ........................................................ 63

APPENDIX

DISPLAY FIRMWARE LEVEL .................................................. A2

UNIVERSAL WEDGE ENABLE ................................................. A3

Blank Page

R44-2006 1

INTRODUCTION

This section provides an overview of program-

ming the scanner with bar code labels in both the

Wedge Mode, and the Scanner Programming Mode,

and provides instruction on how to use this

manual.

SECTION 1 – WEDGE PROGRAMMING

This section provides procedures and bar codes

needed to program interface parameters for the

Wedge Mode.

SECTION 2 – SCANNER PROGRAMMING MODE

This section provides procedures and program-

ming bar codes to change the parameters of your

scanner (speaker volume/tone, UPC-A/UPC-E

Checkdigits, NSD, and Label Identifier Control).

For information on more programmable features

consult PSC'c Advanced Programming Guide,

P/N: R44-2007, available from your PSC dealer or

distributor.

S/HS/Duet Universal-Wedge Quick Start Guide

INTRODUCTION

MANUAL OVERVIEW

This manual is divided into two sections. Each

section presents one of the two programming

features for your scanner – Wedge Programming, and

Scanner Programming.

Wedge Programming – The Wedge programming

includes:

• Interface selection (Keyboard or RS-232)

• Keyboard emulation selection

• RS-232 Wedge interface parameters setting

• End of Message Characters

• Activation of the Cloning Mode.

Scanner Programming – The programmable

features of the scanner includes:

• Speaker Tone/Volume control

• UPC-A/UPC-E CheckDigit

• NSD and Label Identifier control

The Default Wedge Interface is keyboard commu-

nications for PC/AT.

R44-2006 3

INTRODUCTION

Additional terminal programming support is

available from your PSC Dealer or Distributor, or

PSC Customer Support.

Additional scanner features such as Symbology

control, Motor/Laser Timeouts, and Label Data

Editing, are available in PSC Advanced Programming

Guide (R44-2007), available from your PSC Dealer or

Distributor.

To program your scanner for the Wedge or Scanner

features, follow the general procedures on the

following pages.

HOW TO USE THIS MANUAL

Each section in this manual presents a brief

description of the programmable feature and the

bar code labels required. Many pages contain two

bar code labels to conserve resources and reduce

the size of the manual.

NOTE

Since the scanner can perform only one programming function

at a time, it is important to expose only the bar code intended

for programming. Cover the other bar code with and opaque

object, or your hand.

S/HS/Duet Universal-Wedge Quick Start Guide

INTRODUCTION

WEDGE PROGRAMING MODE OVERVIEW

To program your scanner with the Wedge features

go to Section 1 – Wedge Programming, and follow

these procedures:

1. To enable Wedge Programming Mode,

scan the START bar code on page 14.

(The green LED indicator lamp will flash

continuously from BRIGHT to DIM,

indicating the scanner has entered the

Wedge Programming Mode).

2. Scan the desired bar codes labels in the

Wedge programming section of this

guide, pages 16 through 47. (The scanner

will emit a "good read" beep to indicate

each successful bar code read).

3. After all desired programming param-

eters have been entered using the bar

codes, exit the Wedge Programming

Mode by scanning the END bar code on

page 14. (The scanner LED then transi-

tions to a steady ON light to indicate the

scanner is operational).

R44-2006 5

INTRODUCTION

SCANNER PROGRAMMING MODE OVERVIEW

To change the features on your scanner, go to

Section 2 – Scanner Programming and scan the

desired bar codes, using these procedures:

• Enable the Scanner Programming Mode by

scanning the SWITCH bar code on page

52. (The LED indicator lamp will flash

continuously ON and OFF to indicate the

scanner has entered the Scanner Program-

ming Mode).

• Scan the bar code labels on pages 55

through page 70, to enable or disable the

desired features. (The VS and HS scanners

will beep once at each scan to indicate a

"good read", whereas, the Duet will emit

multiple beep tones).).

• Scan the SWITCH bar code on page 52 a

second time to Exit the Scanner Program-

ming Mode. (The scanner will reset, emit

a single power-up beep, and the LED

transitions to a steady ON condition).

S/HS/Duet Universal-Wedge Quick Start Guide

INTRODUCTION

NOTE

Wedge programming bar code labels

useCode39symbology(C39). Factory

configuration has C39 enabled as a

default. IfC39hasbeendisabledinthe

scanner configuration, you must re-

enable C39 in order to program the

wedge interface.

OTHER FEATURES

The wedge interface is able to support multiple

functions such as Editing Mode, which allows the

bar code data to be altered before sending it to the

host terminal. This feature can be set to require

certain conditions be present in the bar code data

(matching characters), and allows the addition of

preambles and/or postambles.

These features are supported in the Advanced

Keyboard Wedge Programming Guide, (R44-2007),

available from your PSC dealer or distributor.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de PSC

PSC

PSC QS200 Manual del propietario

PSC

PSC PowerScan Instrucciones de funcionamiento

PSC

PSC Magellan 8500 Manual de usuario

PSC

PSC FALCON 315 Manual de usuario

PSC

PSC LINEAR IMAGER 7000 Manual de instalación y operación

PSC

PSC magellan 8100 Manual de usuario

PSC

PSC Magellan 2300HS Manual de usuario

PSC

PSC PowerScan RF Guía del usuario

PSC

PSC HD Manual de usuario

PSC

PSC QuickScan QS6500 Manual de usuario

PSC

PSC LazerData Series 9000E Manual de usuario

PSC

PSC MAGELLAN 1000I Manual de instalación y operación

PSC

PSC PowerScan Handheld Instrucciones de funcionamiento

PSC

PSC QuickScan 3000 Manual de instalación y operación

PSC

PSC Falcon 4410 Instrucciones de instalación y funcionamiento

PSC

PSC Duet Manual

PSC

PSC Falcon PT40 Manual de instalación y operación

PSC

PSC QuickScan QS2500 Manual de instalación y operación

PSC

PSC VS800 Manual de usuario

PSC

PSC QuickScan QS6500 Manual de usuario

PSC

PSC LazerData 12000 Series Manual de usuario

PSC

PSC PowerScanTM RF Manual de usuario

PSC

PSC Magellan 2200VS omega Manual de usuario

PSC

PSC QRG QuickScan QS3500 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario

PSC vs1200 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas