Proxim ORiNOCO AP-4900MR-LR Manual de usuario

Quick Install Guide

AP-4900MR-LR

Outdoor Access Point

Software Version 3.3

Part Number 73064 r2 (Print version)

Part Number 73065 r2 (CD version)

Quick Install

NOTICES

reserved. Covered by one or more of the following U.S. patents: 5,231,634;

5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This manual and

part of this publication may be reproduced, transmitted, transcribed, stored in

a retrieval system, or translated into any language in any form by any means

without the written permission of Proxim Wireless Corporation.

Trademarks

ORiNOCO and Proxim are registered trademarks, and the Proxim logo is a

trademark, of Proxim Wireless Corporation. All other trademarks mentioned

herein are the property of their respective owners.

CONTENTS

Notices ........................................................................... 2

Trademarks ..........................................................................................2

Introduction ................................................................... 4

Package Contents........................................................... 6

Hardware and Software Installation............................... 8

Step 1: Choose a Location......................................................................9

Step 2: Pre-Assemble the Hardware ...................................................... 10

Step 3: Connect the Cables .................................................................. 13

Step 4: Power on the Unit .................................................................... 15

Step 5: View LEDs............................................................................... 16

Step 6: Mount the Unit ........................................................................ 17

Step 7: Complete Installation ............................................................... 18

Step 8: Install Documentation and Software ........................................... 19

Unit Initialization ......................................................... 20

Logging In ......................................................................................... 22

Using the Setup Wizard........................................................................ 23

Installing the Software......................................................................... 24

FREQUENCIES AND BANDWIDTHS................................ 26

2.4 GHz Frequencies and Bandwidths..................................................... 26

4.9 GHz Frequencies and Bandwidths..................................................... 26

Technical services and support..................................... 27

Support Options.................................................................................. 27

INTRODUCTION

The AP-4900MR-LR is a ruggedized tri-mode AP optimized for outdoor

deployments. It is equipped with one embedded 4.9 GHz radio and one

embedded 2.4 GHz radio, enabling simultaneous support of 4.9 GHz Public

Safety, 802.11b and 802.11g clients. The 4.9 GHz radio is for use in the

licensed 4.9 GHz Public Safety band; only users with licenses to operate in this

band should access it. The unit also supports Mesh operation on either the 2.4

or 4.9 GHz band.

There are two versions of the AP-4900MR-LR hardware. Differences between

hardware versions are highlighted in this manual as necessary. See Figure 1

and Figure 2.

You can verify which hardware version you are using through either the HTTP

Interface or CLI Interface. See the AP-4900MR-LR User Guide for information on

locating your hardware version number.

AP-4900MR-LR units can operate either using PoE with the combination DC

power supply/injector provided or directly from a 100 - 240 VAC power source

(AC cable ordered separately).

The units feature internal lightning and surge protection on the AC and DC

power ports, the Ethernet port, and on both antenna ports. External antenna

lightning protection is not needed.

Each unit is equipped with:

Power/Ethernet port: used for Ethernet connection and Power over

Ethernet (PoE) using the supplied power injector.

Serial connection: used for entering commands in the Command Line

Interface (CLI). FC versions of the product are not equipped with a serial

connection.

LED indicator(s): dual LEDs used to indicate the power and operational

states of the unit. FC versions of the product are equipped with a single

power LED on the back of the unit in the cooling n area.

AC power input: enables direct power from external AC power source.

External antenna connectors (two): one for 2.4 GHz operation, the

other for 4.9 GHz operation.

Grounding screws (two)

For information on antennas authorized for use with this product, refer to the

AP-4900MR-LR Safety and Regulatory Compliance Guide.

▪

Figure 1: AP-4900MR-LR Unit (Dual LEDs and Serial Connection)

Figure 2: AP-4900MR-LR FC Unit (Single LED and No Serial Connection)

PACKAGE CONTENTS

Each AP-4900MR-LR shipment includes the items in the following table. Verify

that you have received all parts of the shipment.

Note:

Unless listed here, cables are not included with the unit.

AP-4900MR-LR Unit

RJ11 to DB9 serial

connector (not included

with FC units)

Installation CD

Power Injector and Cord (1)

Cable Termination Kit Kit includes:

A. RJ45 connectors (2)

B. Sealing caps (2)

C. Sealing nut

D. Lock nut

E. Grounding screws (2)

A B C D E

Mounting Kit Kit includes the following:

A. Mounting clamp for wall/pole

B. Extension arm

C. Mounting plate to enclosure

D. Mounting clamp for pole mounting

A B C D

Mounting Hardware The following mounting hardware is included

with mounting kit:

Qty. Description

6 ea Plain washer #5/16

2 ea. Hex cap screw NC 5/16-18 x 35

2 ea. Nut NC 5/16-18

4 ea. Helical spring lock washer # 1/4

4 ea. Helical spring lock washer #5/16

2 ea Hex cap screw NC 5/16-18 x 80

4 ea. 68764, Screw, Machine, Pan,

Phillips, 1/4”-20, 5/8”L

HARDWARE AND SOFTWARE INSTALLATION

Notes:

Be sure to read the Release Notes le on the product CD as it contains

software version and driver information that may not have been available

when this document was produced.

Equipment is to be used with, and powered by, the power injector provided

or by a power injector that meets these requirements:

UL-Listed/ITE (NWGQ)

Limited Power Source Output per UL/IEC 60950

CE-marked

Approved for Power-over-Ethernet

Rated output, 48 Vdc/0.42 A

Pinout follows 802.3af standard for mid-span devices

▪

–

IMPORTANT!

Before installing this product, see Safety and Regulatory Compliance

Information on the product CD for important information.

IMPORTANT!

Before installing this product, see Safety and Regulatory Compliance

Information on the product CD for important information.

IMPORTANT!

All AP-4900MR-LR units must be installed by a suitably trained profession-

al installation technician or by a qualied installation service.

IMPORTANT!

All AP-4900MR-LR units must be installed by a suitably trained profession-

al installation technician or by a qualied installation service.

WARNING!

To ensure proper grounding, use the hole at the bottom point on the back

of each unit and the provided grounding screws to attach a ground wire of

at least 10 AWG stranded to each unit. This wire must be as short as pos-

sible and must be connected to a low-impedance earth ground. Use proper

wire grounding techniques in accordance with local electric codes.

WARNING!

To ensure proper grounding, use the hole at the bottom point on the back

of each unit and the provided grounding screws to attach a ground wire of

at least 10 AWG stranded to each unit. This wire must be as short as pos-

sible and must be connected to a low-impedance earth ground. Use proper

wire grounding techniques in accordance with local electric codes.

Step 1: Choose a Location

To make optimal use of the unit, you must nd a suitable location for the

hardware. The range of the radio unit largely depends upon the position of the

antenna. Proxim recommends you do a site survey, observing the following

requirements, before mounting the hardware.

The location must allow easy disconnection of power to the radio if

necessary.

Air must be able to ow freely around the hardware.

The radio unit must be kept away from vibration and excessive heat.

The installation must conform to local regulations at all times.

The units are designed to directly mount to a pole or wall. Using the supplied

brackets and hardware, you can mount them to a 1.25 inch to 4.5-inch pole

(outside diameter). Using just one of the mounting brackets, you can mount

the units to a wall or other at surface.

Caution!

Proxim recommends the use of a lightning arrestor at the building

ingress point. You can purchase the Proxim Lightning Protector; see

the documentation that comes with the unit for more information

and installation instructions.

▪

Step 2: Pre-Assemble the Hardware

Unpack the unit and accessories from the shipping box.

Note the Ethernet and MAC addresses of the unit, as well as the serial

number; these addresses may be used when conguring the unit.

Note:

The serial number is required to obtain support from Proxim. Keep this

information in a safe place.

You will be attaching an outdoor-rated 24 AWG CAT5 cable (diameter .114

to .250 inches/2.9 to 6.4 mm) (not provided) to the Power-over-Ethernet

port on the back of the unit later in the installation procedure. First, you

must construct the cable and assemble the waterproong cable covers as

described in the following steps:

i. Slide the sealing nut (A) over the bare end of the CAT5 cable.

ii. Slide the lock nut (B) over the bare end of the CAT5 cable.

iii. Slide the RJ45 sealing cap (C) over the bare end of the CAT5 cable.

iv. Terminate the RJ45 connector to the CAT5 cable. Insert into the

mating RJ45 connector (D).

v. Slide the RJ45 sealing cap (C) over the RJ45 connector and thread

onto enclosure. Hand tighten.

vi. Thread the lock nut (B) onto sealing cap (C), and hand tighten.

vii. Thread the sealing nut (A) onto the lock nut (B), and hand tighten.

Caution!

Hand-tighten only. Torque values for nal installation are provided

in Step 7: Complete Installation.

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Proxim

Proxim

Proxim Tsunami Multipoint MP-820-BSU-100 Manual de usuario

Proxim

Proxim ORiNOCO AP-4000 Manual de usuario

Proxim

Proxim ORiNOCO AP-700 Manual de usuario

Proxim

Proxim RangeLAN2 7500 Manual de usuario

Proxim

Proxim MP11 5012-SUI Manual de usuario

Proxim

Proxim ORiNOCO AP-4000 Manual de usuario

Proxim

Proxim RangeLAN 802 8520 Manual de usuario

Proxim

Proxim Skyline Manual de usuario

Proxim

Proxim MeshMAX 5054 Manual de usuario

Proxim

Proxim ORiNOCO AP-700 Manual de usuario

Proxim

Proxim ORiNOCO AP-2500 Manual de usuario

Proxim

Proxim Tsunami 800 series Manual

Proxim

Proxim ORiNOCO AP-8000 Manual de usuario

Proxim

Proxim Harmony 802.11b Manual de usuario

Proxim

Proxim ORINOCO AP-2000 Manual de usuario

Proxim

Proxim Harmony 802.11b Manual de usuario

Proxim

Proxim ORiNOCO AP-4000 Manual de usuario

Proxim

Proxim Harmony 8570 Manual de usuario

Proxim

Proxim Antenna Tsunami MP.11 Manual de usuario

Proxim

Proxim ORINOCO AP-2000 Manual de usuario

Proxim

Proxim Antenna Tsunami MP.11 Manual de usuario

Proxim

Proxim ORiNOCO AP-8000 Manual de usuario

Proxim

Proxim ORiNOCO AP-9100 Manual

Proxim

Proxim ORiNOCO AP-2500 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario