Protect America Simon XT Guía
Protect America Installation Manual and User Guide
This manual is the property of Protect America, Inc. This installation
manual contains condential information which is proprietary to Protect
America, Inc. You may not disclose this information to third parties and
you may not copy all or any part of this installation manual.
Table of Contents
Simon XT Easy Installation Manual
Step 1: Check Package Contents .................................. page 2
Step 2: Connect the Simon XT ...................................... page 3
Step 3: Get to Know the Simon XT ................................ page 4
Step 4: Chime, Clock & User Setup ............................... page 5
Step 5: Installing Your Sensors ...................................... page 6
Step 6: Activate Your System ......................................... page 7
Sensor Information Worksheet ...................................... page 8
FCC Notices .................................................................. page 9
Simon XT User Guide
Product Overview .......................................................... page 10
Simon XT Key Features ................................................. page 11
Access Codes and Arming/Disarming ............................ page 12
Top Level Menus ............................................................ page 16
Security System Beeps and Messages ......................... page 19
Smoke and Heat Detector Locations ............................. page 21
Testing Your System ...................................................... page 22
False Alarm Prevention ................................................. page 24
Frequently Asked Questions ......................................... page 26
Cellular Conversion Installation Manual ....................... page 28
GPS Vehicle Tracking Device ......................................... page 34
IMPORTANT
Complete User Setup Worksheet Before You Begin
A very important step in the installation process is deciding your 4-digit Master
Code, Duress Code, Verbal Password, Emergency Contacts, and Additional
User Codes. Please refer to User Setup on the bottom of page 5 and ll out the
USER SETUP WORKSHEET before you begin the installation process. This is
an important step for the safety of your home and family. It will also save you a
lot of time during the alarm activation process.
The Simon XT Easy Installation Manual
1
Simon XT Installation
Step 1: Check Package Contents
1.2 — Verify Materials
!
Find a convenient location for your Simon XT control panel. It should be located
near a phone jack and a non-switched electrical outlet. It should be in a location
that can be accessed easily when entering or leaving the home.
Doors +
Windows Motions Disarm Status
Silent Bypass
Simon
XT
Disarmed
12:23a
PA
S
CK
L
G
P
IN
I
1.1 — Verify Contents
Locate your packing slip. Use your packing slip to verify the contents of your package.
(1) Screwdriver
(2) 0.5" Screws per Microsensor
(2) Plastic Wall Anchors
(2) 0.75" Mounting Screws
(1) Plastic Spacer per microsensor (1) Line Grabber
(Not included with HomePulse or
Cellular - do not install unless instructed
by Tech Support)
2
Simon XT Installation
Step 2: Connect the Simon XT
2.3 — Plug in the Power Supply
Make sure you properly secure the power supply to a non-switched and non-GFCI outlet faceplate.
Plug in power supply and secure
with screw provided.
Unscrew the faceplate. Ensure that power supply is secure.
DO NOT PLUG IN YOUR SIMON XT!
You must connect the battery
before
plugging your Simon XT into the wall outlet.
2.1 — Connect the Battery
CLICK
Turn Simon XT and locate the two red
wires on the back of the Simon XT
control panel.
Clip the two wires together. The
Simon XT will power on & beep. Not
included for HomePulse OR Cellular
3
Broadband
CLICK
Landline
CLICK
2.2 — Connect the Phone Cord or the Ethernet Cable — Cellular users skip this step
Standard and Two-Way Voice customers follow the "Landline" instructions. HomePulse Broadband customers follow the
"Broadband" instructions.
Locate the phone wire labeled "Wall" on the back of the Simon XT
and plug it into the wall phone jack.
Locate the ethernet cable on the back of the Simon XT and
plug it into your router. This must be done before connecting
the battery wires.
OR
Simon XT Installation
Step 3: Get to Know the Simon XT
3 — The Controls
Doors +
Windows Motions Disarm Status
Silent Bypass
Simon
XT
Disarmed
12:23a
Enter
Press to select a particular
menu item or commit to
memory a menu item
that has just been
programmed.
Motions
Press to arm interior sensors.
Siren
The piezo siren is used
for status beeps and
alarms. Fire and intrusion
alarms always sound at
high volume. The volume
of status beeps (such as
trouble or chime beeps,
entry and exit delay
beeps, or auxiliary alarm
beeps) are programmable.
Disarm
Signies the system is
armed when lit. When
illuminated, pressing
the button will prompt
you to enter your
access code to disarm
the system.
Keypad
Twelve-key keypad for
entering access codes or
other numerical data.
*
Turn on lights (additional
equipment is required).
Emergency
Buttons
Press and hold button
for two seconds (or press
twice quickly) to notify
the central monitoring
station of a call for help.
Police
Emergency
Emergency
LCD Display
The LCD display can
show a variety of
phrases and icons.
Doors + Windows
Press to arm
perimeter sensors.
Scroll Up /
Scroll Down
Press to scroll
through the menus.
Silent
Press to silence exit
beeps when arming.
Status
Press to check
system status.
Bypass
Press to bypass a sensor.
Speaker
Used for voice output and
key beeps. The Simon
XT speaks arming level
changes, system status,
and voice-chime
sensor trips.
#
Turn off lights (additional
equipment is required).
4
Simon XT Installation
Step 4: Chime, Clock & User Setup
Set the Clock
Press SCROLL UP ( ) until the display reads "Set Clock," and then press ENTER ( ).
Enter the master code, then press ENTER twice ( ).
If no master code has been set, the default master code is 1234.
The hour should be blinking. Type in the current hour using the KEYPAD then press ENTER ( ).
The minute should be blinking. Type in current minute using the KEYPAD then press ENTER ( ).
Press SCROLL UP ( ) to select "am" or "pm," then press ENTER ( ).
Press STATUS twice (
Status Status
) to return to the main menu.
USER SETUP WORKSHEET
Code Description Code
Master Code
User Code 1
User Code 2
User Code 3
User Code 4
User Code 5
User Code 6
User Code 7
User Code 8
Duress Code
Verbal Password
Emergency Contacts Name Phone 1 Phone 2
Emergency Contact 1
Emergency Contact 2
Emergency Contact 3
Turn on Chime
If the chime is on and the system is disarmed, the Simon XT panel will use voice notication when doors or windows are opened.
When the chime is on, a bell icon is shown on the display.
Press SCROLL DOWN ( ) until the display reads, "Chime," then press ENTER ( ).
Press SCROLL UP ( ) to select “on” or “off,” then press ENTER ( ).
(Note: It is recommended that the chime be turned on while installing sensors.)
Press STATUS ( Status ) to return to the main menu.
Programming the Simon XT requires keys to be pressed in order, with little or no
delay. It is recommended that you familiarize yourself with these steps before
beginning. For initial programming, the default master code is 1234 ( ).
5
Simon XT Installation
Step 5: Installing Your Sensors
5.1 — Install Door & Window Sensors
Place marked sensors in their proper location. Additional sensors may be placed to your liking. When placing
sensors, make sure that the arrows on each side are aligned.
3
/
8in
magnetsensor
Make sure that the sensor and magnet are
within 3/8" of each other. Use spacers on
metal doors or to aid proper sensor alignment.
Use the provided self-adhesive velcro to
secure the sensor to the door or window,
and the magnet to the door or window frame.
Determine an appropriate location for
each sensor.
6.5-7ft6.5-7ft
Place the motion detector in the corner of
the room, 6.5-7 feet above the ground.
Use the self-adhesive velcro to secure
the motion detector in a corner.
25 ft
Each motion detector protects up to a
25' range in a 90° arc.
5.2 — Install Motion Detector (If Included)
Motion detectors should be placed in the highest-trafc areas of your home, e.g., a living room or a hallway.
!Make sure to clean the installation location before applying each sensor.
Upon installing, write the location of each sensor on the "Sensor Information
Worksheet" located on page 8 of the installation manual for future reference.
6
Simon XT Installation
Step 6: Activate Your System
Congratulations!
Your system is now installed and ready to be activated.
Post-installation Service & Support
If you need any help or service after installing your system, call us toll-free at 1-800-951-5111.
Monitoring
When a proper user code is entered within sixty (60) seconds of an alarm activation, the system is
disarmed and a cancel code is sent automatically to the monitoring station. No further steps are
necessary and the monitoring station will not take action.
If a proper user code is not entered within sixty (60) seconds of an alarm activation, the siren will
sound and the monitoring station will take action.
If an intrusion alarm has been triggered and is not deactivated, the monitoring station will attempt
to call and verify an authorized contact. If there is no answer, if the line is busy, or if the contact
does not know the correct password, then the monitoring station will immediately notify the proper
authorities.
Additional Equipment
If you purchased additional equipment that is not found in this manual, please call toll free
1-800-951-5111 to speak with our Installation representatives.
Call to Activate
Protect your home and family today!
Your system is not yet active—you must call Protect America
to activate your system!
When calling, please have your Sensor Information Worksheet and your Packing Slip at
hand. A representative will guide you through the activation process.
Call toll-free:
1-800-951-5111
and select the option "to install and activate your new security system"
If any siren has gone off, disarm the system, then contact the monitoring station
toll-free at 1-877-274-0604.
7
Simon XT Installation
Sensor Information Worksheet
Sensor
Number Sensor Name Sensor Type Location
Example Front Door Door/Window Sensor Front Door
Sensor 1
Sensor 2
Sensor 3
Sensor 4
Sensor 5
Sensor 6
Sensor 7
Sensor 8
Sensor 9
Sensor 10
Sensor 11
Sensor 12
Sensor 13
Sensor 14
Sensor 15
Sensor 16
Sensor 17
Sensor 18
Sensor 19
Sensor 20
Sensor 21
Sensor 22
Sensor 23
Sensor 24
Sensor 25
Sensor 26
Sensor 27
Sensor 28
Sensor 29
Sensor 30
Sensor 31
Sensor 32
Sensor 33
Sensor 34
Sensor 35
Sensor 36
Sensor 37
Sensor 38
Sensor 39
Sensor 40
8
Otros manuales para Simon XT
1
Tabla de contenidos
Otros manuales de Sistema de seguridad de Protect America
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario