Promise ConnectStor II Manual de usuario

User’s Guide

may be reproduced or transmitted in any form without the expressed, written

permission of Promise.

Trademarks

All trademarks are the property of their respective holders.

Important data protection information

You should back up all data before installing any drive controller or storage

peripheral. Promise is not responsible for any loss of data resulting from the use,

disuse or misuse of this or any other Promise product.

Notice

Although Promise has attempted to ensure the accuracy of the content of this

manual, it is possible that this document may contain technical inaccuracies,

typographical, or other errors. Promise Technology, Inc. assumes no liabilityfor any

error in this publication, and for damages, whether direct, indirect, incidental,

consequential or otherwise, that may result from such error, including, but not

limited to loss of data or profits.

Promise provides this publication “as is” without warrantyof any kind, either

express or implied, including, but not limited to implied warranties of

merchantability or fitness for a particular purpose.

The published information in the manual is subject to change without notice.

Promise reserves the right to make changes in the product design, layout, and driver

revisions without notification to its users.

Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy,

and, if not installed and used in accordance with the instruction may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult Promise Technology, Inc. or an experienced radio/TV technician

for help.

This device complies with Part 5 of the FCC Rules. Operation is subject to the

following conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

NOTE: Only digital device equipment CERTIFIED CLASS B should be attached

to this equipment and that must have shielded cables.

Table of Contents

Trademarks___________________________________________ii

Important data protection information_____________________ii

Notice________________________________________________ii

Radio Frequency Interference Statement __________________ iii

Introduction _______________________________________ 1

Key Features__________________________________________2

Specifications__________________________________________3

Interface _________________________________________________3

Enclosure ________________________________________________3

Physical/Environmental_____________________________________3

Warranty_________________________________________________3

Getting Started_____________________________________ 5

Necessary Equipment for Installation______________________5

Unpacking ConnectStor II_______________________________7

Installing Hard Drives __________________________________8

Hooking Up ConnectStor II Hardware ___________________11

Install the Mounting Feet___________________________________11

Connect the Network Cable _________________________________11

Connect the Power Cord ___________________________________12

Power Switch ____________________________________________12

Configuring ConnectStor II IP Address___________________13

Configuring ConnectStor II _________________________ 15

Logging In___________________________________________16

About ConnectStor II's Configuration Menu_______________17

Changing or Viewing System Settings_____________________19

Changing Network Settings_________________________________19

Changing Date/Time Settings _______________________________21

Configuring UPS Support __________________________________23

Configuring E-Mail Notification Options ______________________24

Changing IP Address Assignment Mode __________________26

Changing Language Setting_________________________________28

Viewing Operating Status ______________________________29

User Options_________________________________________30

Viewing Current Users_____________________________________30

Creating a User __________________________________________31

Modifying a User _________________________________________32

Deleting a User___________________________________________34

File Sharing__________________________________________35

Viewing Current Shared Folders _____________________________35

Creating a New Shared Folder_______________________________36

Modifying Shared Folder Properties __________________________37

Deleting an Existing Shared Folder___________________________38

UNIX (NFS) Settings __________________________________39

Viewing Current Settings___________________________________39

Creating New UNIX/Linux Server Settings ____________________40

Deleting a UNIX/Linux Server ______________________________40

Password Server Options_______________________________41

Enabling Password Server Support ___________________________41

RAID Options________________________________________43

About RAID Arrays _______________________________________43

Viewing Current RAID Array Status__________________________44

Viewing Physical Drive Status_______________________________44

Selecting Another RAID Level ______________________________46

Halt / Reboot ConnectStor II ___________________________47

Halting ConnectStor II_____________________________________47

Remotely Rebooting ConnectStor II __________________________47

Advanced Configuration Commands _____________________48

Updating System _________________________________________48

Restoring ConnectStor II to Default Settings ___________________49

Exit Command _______________________________________50

Using ConnectStor II_______________________________ 52

Mapping ConnectStor II to Individual PCs ________________52

Using ConnectStor II For Storage _______________________55

Troubleshooting ConnectStor II______________________ 57

Using ConnectStor II's Front Panel Display________________57

Power Status LED Messages ________________________________57

General Troubleshooting Issues _________________________60

TCP/IP Is Not Enabled in Windows 95/98/ME__________________60

Cannot Find Workgroups in Windows 95/98/Me ________________60

Cannot See ConnectStor II Over Network______________________61

Cannot Find ConnectStor II in Network Neighborhood ___________61

Standard Conventions

Common identifiers:

↵- Press the Enter key

[Key] - Press the key(s) shown within the brackets

NOTE: Supplementary material containing important

information

Screen messages:

Type of text Display

Normal Looks like this

Messages appearing on screen Messages appearing on

screen

Typed commands or text “Text that you type”

Values you replace with type “Values that you replace”

File, path, and share names Filenames

ConnectStor II Chapter 1

- 1 -

Introduction

Thank you for purchasing Promise Technology’s ConnectStor network attached

storage (NAS) subsystem. ConnectStor II takes full advantage of Promise

Technology's leadership in ATA RAID product design by providing RAID 0, 1

support for the latest low-cost Ultra ATA/100 hard drives.

ConnectStor II offers users the ability to provide continuous data protection using

two-drive RAID 1 mirroring or to build increased storage capacity using RAID 0

striping of two drives. Either way, users take advantage of the increased economy,

performance, and capacity of Ultra ATA drives for their particular network

environment.

ConnectStor II houses file sharing protocols for Microsoft®Windows®95,

Windows®98, Windows NT®(v.4), Windows®2000, Windows®Me, NFS 2.0,

making it virtually a plug and work device with most major network operating

systems.

Best of all, you can easily manage and configure ConnectStor II from most major

web-based browsers (see Specifications). The password-protected management

utility lets users and/or network administrators customize ConnectStor II for direct

connection to UNIX (NFS), HTTP, and SMB/CIFS (Windows) network protocols

and includes a full suite of reporting and monitoring tools.

ConnectStor II Chapter 1

- 2 -

Key Features

The following are key features of the Promise ConnectStor II:

Drive Types

• Supports up to two 3.5” IDE drives (Ultra ATA, DMA, and EIDE)

• Supports Ultra ATA/100, Ultra ATA/66, Ultra ATA/33, EIDE, and Fast

ATA-2 speeds (UDMA 5/4/3/2/1/0 and DMA 2/1/0, respectively)

Status Indicators

• Power Status LED shows power on/off and system status

• Drive Activity LED displays drive activity (reads or writes)

• Network Activity LED displays individual network requests

Ultra ATA/100 Support

• 100MB/sec burst data transfers of Ultra ATA/100 drives

• Implements high-speed CRC error-checking

RAID 0, 1 Functions

• RAID 1 (mirroring) sends identical data to two installed drives

• RAID 1 maintains access to data if a single drive fails

• RAID 1 rebuilds data to replacement drive automatically

• RAID 0 (striping) links up to two drives as a single large capacity drive

volume (no fault protection)

• RAID 0 with two drives doubles sustained data transfer rate to speed up

large file transfers

Network Support

• Built-in 10/100Mb/s Ethernet controller for high data transfers

• Supports popular network protocols: TCP/IP, NFS, SMB/CIFS

Configuration & Monitoring

• Easy setup and monitoring of ConnectStor II unit via web browser

(requires MS Internet Explorer 5 or higher, Netscape Navigator 4 or

higher)

• IPassign™ utility to manually assign IP address IF network does not

support automatic IP address assignment (DHCP/BOOTP)

Otros manuales para ConnectStor II

Tabla de contenidos

Otros manuales de Servidor de almacenamiento en red de Promise

Promise

Promise VTRAK 15100 Manual de usuario

Promise

Promise VTrak J5960 Manual de usuario

Promise

Promise VSky H3970rDM Manual de usuario

Promise

Promise E310f Manual de usuario

Promise

Promise VessRAID 1740s Manual de usuario

Promise

Promise SmartStor NS4700 Manual de usuario

Promise

Promise PegasusPro R8 Manual de usuario

Promise

Promise VTRAK J300S Manual de usuario

Promise

Promise Atlas S8+ Manual de usuario

Promise

Promise ConnectStor II Manual de usuario

Promise

Promise PegasusPro R16 Manual de usuario

Promise

Promise VTRAK M610i Manual de usuario

Promise

Promise Smartstor NS4600 Manual de usuario

Promise

Promise VSky H3970 Manual de usuario

Manuales populares de Servidor de almacenamiento en red de otras marcas

HP NetStorage 6000 Manual de usuario

Seagate

Seagate U10 ST320423A Manual de usuario

Synology

Synology RackStation RS816 Manual

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manual de usuario

Avid Technology

Avid Technology VideoRAID ST Guía de seguridad

Western Digital

Western Digital My Cloud Home Duo Manual de usuario

PrimeArray

PrimeArray 4xxx Manual de usuario

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manual de usuario

Planex

Planex MZK-NAS01SG Manual de usuario

Intel

Intel SS4000-E - Entry Storage System NAS Server Manual de usuario

Synology

Synology RS2212+ Manual de usuario

Allnet

Allnet ALL69000 Manual de usuario

Adaptec

Adaptec 5325301580 Manual de usuario

Motorola

Motorola EXORdisk II Manual de usuario

Sony

Sony XDAAI1PK Manual de usuario

Cisco

Cisco Linksys NAS200 Instrucciones de funcionamiento originales

Sans Digital

Sans Digital MR4UT6G Manual de usuario

AIC

AIC FB128-LX Manual de usuario