Technical details
Power supply Battery 2 x AAA 1.5v
Operating frequency 423.92 MHz
Transmission power/Range 5 MW pulsed, 15 to 20 metre linear distance
Size / Weight 10.9 X 6.5 X 2.0 cm, 120 g
Manufacturer PROCON GmbH, Hamburg
What does the LED display on the moisture sensor?
• If the sensor is ready for use
, the LED will not be on.
• If the alarm sounds
, the LED signal will flash very quickly for 12 seconds.
• As long as the sensor is damp, the LED will flash slowly. When everything is dry, the
signal stops and the sensor is ready for use again.
How do I test the wireless connection?
Place the receiver next to the child’s bed and touch the
gold side of the sensor in the child’s bed with a moistened
finger. With a secure connection the alarm receiver
will be triggered within two seconds. Thereafter place
the receiver in the parents’ room and repeat the sensor
testing from the child’s bed.
What is the range of the wireless signal?
Under normal circumstances the wireless signal between the sensor and the receiver works
at a distance of up to 20 metres, including through thick walls.
What could interfere with the wireless connection?
Sources with strong electromagnetic waves like TVs, computers, telephones and especially
transformers for halogen lamps can interfere with the wireless connection. Should Enutrain®
not function in your house, please remove all the named devices from the power plug and
repeat the wireless connection test. In many homes the electromagnetic waves are concen-
trated under the ceiling of the room. For this reason it is advisable that children do not sleep
in bunk beds while doing the wake-up training with Enutrain®.
How do I test the battery for the moisture sensor?
The battery for the sensor usually lasts for about one year. To test the battery condition, simply
activate a practice alarm with a moistened finger. If the LED does not flash, the battery is
depleted. It cannot be exchanged. If needed, please contact your doctor so that he or she can
prescribe you a replacement sensor.
Can I use rubber mats or rubber sheets with Enutrain®?
Children get statically charged at night when the mattress is covered with a rubber sheet,
which can trigger a false alarm. For this reason rather use a molleton sheet as a mattress
protection.
Can I use nappies and panty liners with Enutrain®?
The sensor can only reliably trigger the alarm when it comes into contact with the first drops
of urine. Nappies and panty liners usually have moisture-retaining materials that are unsuita-
ble for wake-up training. For the duration of the treatment please use the included sensor
briefs.
Important information about the receiver
In addition to a button, the receiver also features a light-emitting diode (LED), which provides
you with information about the current status of the device.
How do I switch the receiver on?
Hold the button down for about half a minute, until the green LED
flashes twice and the device beeps twice.
How can I tell if the device has been switched on correctly?
After switch-on the operational status of the receiver is indicated with a green light that flashes
on and off continuously.
How do I switch the receiver off?
Hold the button down for about one second
until the diode turns red.
Then release your finger and the device will beep when it switches off.
How do I select the different alarm options?
In the default setting the receiver emits an acoustic alarm. If you would like another option,
switch the receiver on and wait until the operation status is indicated with a flashing green
light. Then press the button down until the LED alternates between flashing in red and green.
Now you can select the desired alarm option
by pressing the button:
Press 1x: vibration alarm
Press 2x: combination alarm with beeping and vibration
Press 3x: acoustic alarm with beeping
After the selection the device is ready for operation.
The receiver retains the selected option until you change
the setting again.
How can I tell if the batteries are still fine?
When the receiver flashes the red light instead of
the green one, the batteries should be changed shortly.
When the battery is almost empty, the receiver will
beep and the red light will flash before it switches off.
What does it mean when the receiver has no reaction?
Usually when the receiver has no light or sound it means that the batteries are empty. If after
properly replacing the batteries there is still no reaction, it could be faulty. In this case, please
contact the supplier or the Procon Team.
How to I replace the batteries?
The receiver is equipped with 2 AAA batteries, which you can easily exchange. Please make
sure that you use new batteries and insert them with the correct polarity (+ on + and - on -).
Under normal circumstances the batteries have a lifespan of about four months.
General information
Enutrain® Mobil is the intelligent wake-trainer for nighttime bedwetting (enuresis nocturna) and
daytime bedwetting (enuresis diurna). The standard version comprises one receiver, one
moisture sensor and two sensor briefs in your child’s size.
Both the sensor and the receiver contain valuable electronic quartz crystals for wireless
transmission. Please handle the device with care and also show your child how to use it
carefully.
• Do not expose the sensor and receiver to
any heavy knocks
• Prevent it from falling down on hard surfaces
• Remember to remove the sensor from the
sensor briefs before washing them
• For day use your child should if possible
carry the receiver in a bag
Questions concerning operation are answered in this guide. Please read through it carefully.
Should you have any further technical questions, please contact the Procon Team (see back
page for address) or refer to our website under www.enutrain.de. We wish you much success
with the treatment.
Where can I get more sensor briefs from?
You can order sensor briefs in packs of two from Procon.
Can I treat two or more children in one household?
Yes, that’s possible. Please contact the Procon Team directly for this.
Is the radiation really not harmful for my child?
You don’t need to have any concerns regarding a high exposure to radiation. The power signal
of the sensor is only 5 milliwatts, which is less than one thousandth of the signal of a conven-
tional mobile phone, and it is only emitted when the alarm sounds. The receiver does not emit
any radiation.
How long does the sensor last for?
The sensor has a gold-plated surface and is sealed to protect the electronics and battery from
the corrosive urine. With careful handling (like promptly drying it after bedwetting) it will last for
about one year.
How long does the battery last for?
The sensor is permanently on alert yet consumes very little electricity. Upon delivery the
battery will last for about 1000 alarm cycles in the first year. Thereafter you should reckon with
reduced serviceability.
What should I do in the event of damage to the devices?
Damages due to improper use and through tampering with the sensor and receiver will not be
covered under the warranty. In the event of faults, please contact the suppliers or the Procon
Team.
