Pro-Ject Audio Systems Debut Carbon DC Manual de usuario

INSTRUCTIONS FOR USE

Pro-Ject Debut Carbon DC

Dear music lover,

thank you for purchasing a Pro-Ject Audio record player.

In order to achieve maximum performance and reliability with this record player you should study these instructions

for use carefully.

** Your turntable has been delivered with a factory fitted and adjusted cartridge. Please ignore the

cartridge set up instructions unless changing the cartridge at a later date.

During assembling and adjusting of the deck, small parts could be lost if not carefully placed in a suitable

receptacle. Before starting the assembly, make yourself acquainted with the parts listed below and

correspondingly numbered in the technical drawings above. Separately packed items are marked with an

asterisk *.

Parts list

1 Motor brackets with Ortofon®pads

2 Stepped drive pulley

3 Drive belt * 3a Hook *

4 Hub

5 Platter with felt mat *

6 Tonearm counterweight * 6a Downforce scale

7 Tonearm lift lever

8/18 Tonearm rest and removable transport lock

9 Tonearm tube 9a Tonearm base

10 Lid *

11 Lid hinges

12 Hinge fasteners

13 Power supply socket

14 Phono output sockets and earth connection

15 Anti-skating weight adjustment scale

16 Anti-skating weight *

17 Anti-skating weight support hoop

19 Power switch

20 Headshell with finger lift and fitted Ortofon OM 10 or Ortofon 2M Red cartridge

21 Motor

22 Single adapter *

Connection cable (not shown) *

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

Safety instructions

Make sure that the plug and the switch are easily accessible at all times. Hold the plug when

unplugging the power cord. Never handle the power cord while your hands are wet or damp.

Avoid letting liquids enter the device. Never place any item containing liquid, such as a flower vase

on or near the device. Never spill any liquid on the device. Never place any naked flame sources,

such as lighted candles on or near the device. The product shall not be used in damp or wet locations,

next to a bathtub, sink, swimming pool or any other similar conditions.

Keep plastic bags away from children to prevent any risk of suffocation.

Set-up

The deck is supplied partially disassembled and carefully packed to guarantee a safe transport. Remove all

parts from the transport packaging carefully.

Make sure the surface you want to place the turntable is levelled (use a spirit level).

Remove the transport lock (18) from the tonearm. Store it in the original packaging so it is available for

future transportations.

Fit the drive belt (3) around the hub (4) and the smaller diameter part of the motor pulley (2). Avoid getting

sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use

absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt. Put the

platter (5) and felt mat over the spindle of the hub (4).

Cartridge downforce adjustment

The counterweights (6) supplied are suitable for cartridges weighing between 4,5 - 6g (

Ortofon OM 10

weight no.

) and 6,5 - 8,5g (

Ortofon 2M Red

- weight no.

Turn the counterweight (6) onto the rear end of the tonearm tube (9), so that the downforce scale (6a) shows

towards the front of the player. Lower the arm lift and place the cartridge in the space between arm rest and

platter. Rotate the counterweight (6) until the arm tube is balanced. The arm should return to the balanced

position if it is moved up or down. This adjustment must be done carefully. Do not forget to remove the

cartridge protection cap if fitted before balancing the arm tube.

Once the arm is balanced correctly, return it to the rest. Hold the counterweight (6) without moving it and gently

revolve the downforce scale ring (6a) until the zero is in line with the anti-skating prong (15). Check if the arm

is still balanced.

Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the

cartridge manufacturer's recommendations. One mark on the scale represents 1 mN (= 0,1g / 0,1 Pond) of

downforce.

Please note: Adjust the downforce before installing the anti-skating weight.

The recommended downforce for Ortofon OM 10 cartridge is 15mN.

The recommended downforce for Ortofon 2M Red cartridge is 17,5mN.

Anti-skating force adjustment

The anti-skating force must be adjusted corresponding to the downforce:

Downforce Groove in the stub (15)

10 - 14mN 1st bearing ring

15 - 19mN 2nd bearing ring

20mN and higher 3

bearing ring

Slip the loop of the anti-skating weight's thread over the second groove of the stub to set the correct anti-

skating force for the factory-fitted cartridge. Feed the thread through the loop of the wire support (17).

Connection to the amplifier

The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables

supplied with higher quality cables such as the

Pro-Ject Connect it

interconnect cables for connection to the

amplifier.

Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input

offers correct matching and amplification for the used cartridge. Line inputs (such as CD, Tuner, Tape or Video)

are not suitable.

Take care of connecting the left and right channels correctly. The right channel is usually marked red, the left

channel black or white. Check the manual supplied with your amplifier for relevant information. The earthing

wire of the tonearm should be connected to the earth terminal on your amplifier (if provided).

If your amplifier does not have an input suitable for phono cartridges you will require a separate phono

amplifier stage for MM or MC cartridges which is then connected between the record player and a free line

level input of the amplifier.

For detailed product information regarding Pro-Ject Audio interconnect cables and phono amplifiers please

visit the Pro-Ject web site

www.project-audio.com.

The recommended load impedance for the factory fitted cartridges is: 47kohms/MM-input

Mains power connection

The turntable is supplied with the universal power supply with 3 exchangeable sockets adapters suitable for

all countries. Select the correct adapter for your country and insert the adapter to the exchangeable part of

the power supply.

Connect the low voltage plug from the power supply to the socket (13) on the rear of the record player before

connecting the power supply to the mains.

Mounting the lid

Put the lid (dust cover 10) carefully over the hinge prongs and adjust the screws (12) until the lid stays open

where you want it to without being too stiff to open or close.

Switching on and off

Pressing the power switch (19) alternately starts or stops the motor.

Changing replay speed

To play records at 45 r.p.m. remove the platter (5). Use the accessory tool provided (3a) and hook the belt

(3) over the larger diameter part of the motor pulley (2). Put the platter on. To revert to 33 r.p.m. repeat the

proceedings using the smaller step on the pulley.

*** In addition, 78 r.p.m. is available after mounting a special pulley, which may be purchased as an

optional extra.

For detailed product information please visit the Pro-Ject web site www.project-audio.com.

Useful tips

The record player should be positioned on a low-resonance surface such as wood or a multiple layer play

board to avoid structural vibrations disturbing replay.

Adjusting the azimuth

** The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations

correctly.

A small screw at the bearing end of the arm allows to correct incorrect azimuth

if your needle is not

mounted exactly perpendicular to the cartridge body.

Open the screw just enough to be able to revolve the arm tube without applying force. Please note: do not

remove the screw completely!

With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i.e. perpendicular

to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel

to the record surface.

After adjusting the needle parallel, retight the screw carefully.

Please note: Under no circumstances should the arm tube be adjusted with the needle still in the

record groove! Irreparable damage may be caused to the cantilever suspension! The arm must be

lifted to make each adjustment and lowered afterwards to check it.

Mounting and connecting the cartridge

** All cartridges with half inch mounting holes can be fitted. Leave the needle's protection cover on and put

the cartridge on the headshell by using the cartridge supplied screws. Pass one screw through each slot in

the headshell (20). Do not tighten the nuts yet.

Connect the tonearm wires to the cartridge pins as follows:

white left channel positive (L+)

red right channel pos. (R+)

green right channel return (R -)

blue left channel return (L -)

The full sound quality of the record player can only be achieved if the cartridge is adjusted correctly. Particular

tools like the Pro-Ject Audio Systems alignment tool are required to accomplish this job properly.

If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of

your Pro-Ject dealer to accomplish it for you.

Please note: Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging

the cartridge or tonearm bearings. Leave this work to your dealer if you are in any way unsure of the

necessary steps and precautions to be taken.

Maintenance and cleaning

Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic

cloth. To avoid static electricity (which attracts even more dust), do not use a dry cloth! Antistatic cleaning

fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts. It is

recommended to put on the needle cover before cleaning to avoid damage.

If the player is not used for a long time, the drive belt should be removed to prevent unequal stretching.

Always disconnect the record player from the mains power supply as a precaution before maintenance!

Technical specifications Pro-Ject Debut Carbon DC/ Pro-Ject 8.6cc

Nominal speeds

33/45 r.p.m.. *** 78 r.p.m. optional

Speed variance

33: 0,2% 45: 0,16%

Wow and flutter

33: 0,12% 45: 0,11%

Signal to noise

68dB

Effective tonearm mass

Effective tonearm length

8,6 " ( 218,5mm)

Overhang

18,5mm

Power consumption

4W/0W in Stand-By

Outboard power supply

15V / 0 – 0.8mA DC (set at 0.5mA), universal power supply

Dimensions (W x H x D)

415 x 118 x 320mm, dust cover open 415 x 365 x 405mm

Weight

5,6kg

Technical specifications MM-Cartridge Ortofon OM 10

Frequency range

20-22.000Hz

Channel separation

22dB/1kHz

Output voltage

4mV

Recommended load impedance

47kohms/amplifier connection – MM-input

Compliance/stylus type

25µm/mN – elliptical

Recommended tracking force

15mN

Weight

Technical specifications MM-Cartridge Ortofon 2M Red

Frequency range

20-22.000Hz

Channel separation

22dB/1kHz

Output voltage

5,5mV

Recommended load impedance

47kohms/amplifier connection – MM-input

Compliance/stylus type

20µm/mN – elliptical

Recommended tracking force

18mN

Weight

7,2g

Potential incorrect use and fault conditions

Pro-Ject Audio Systems turntables are manufactured to the highest standards and undergo strict quality

controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or

production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the

following list of common fault symptoms is included.

The platter does not turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or

from that to the phono box or between that and the amplifier. This could be due to a faulty plug,

broken wire or solder joint or missing plug/socket connection.

Phono input is not selected at amplifier.

Amplifier is not switched on.

Amplifier or speakers are defective or muted.

No connection to the loudspeakers.

Strong hum on phono input:

No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.

Distorted or inconsistent sound from one or both channels:

Record player is connected to a wrong input on the amplifier, or MM/MC switch is setted incorrectly.

Needle or cantilever is damaged.

Wrong r.p.m., drive belt is overstretched or dirty, platter bearing is without oil, dirty or damaged.

Service

Should you encounter a problem which you are not able to alleviate or identify despite the above information,

please contact your dealer for further advice. Only if the problem cannot be resolved there, the unit should

be sent to the responsible distributor in your country.

Guarantee repairs will only be effected if the unit is returned correctly packed. For this reason we recommend to

keep the original packaging.

Never return a record player without making sure that it is disassembled safely and packed correctly in the

original packaging according to the diagrams on the last page of this user guide. Please remove these parts

and pack them separately: lid (10), counterweight (6), anti-skating weight (16) platter (5) and belt (3). Put on

the cartridge protection cap. Insert the transport lock for the tonearm (18) before packing the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or changes to any part

of the product by unauthorized persons, releases the manufacturer from any liability over and above

the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of H.

Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct a

t the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Otros manuales para Debut Carbon DC

Tabla de contenidos

Otros manuales de Placa giratoria de Pro-Ject Audio Systems

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 6.1 SB SuperPack Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems ESSENTIAL III Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems 2 Xperience Basic + Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 1 Carbon Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Speed Box MK II Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Primary Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtensions 9 S-Shape Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems THE CLASSIC Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut RecordMaster II Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension 10 Evolution Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box E Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential III RecordMaster Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 SuperPack 1 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon Phono/USB Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject VC-S Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems ESSENTIAL III Guía de solución de problemas

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II Demon Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems X8 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Jukebox E Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems 9 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems A2 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 5.1 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Debut III E Manual de usuario

Manuales populares de Placa giratoria de otras marcas

Gemini

Gemini CDT-05 MKII Manual de usuario

Rotel

Rotel RP-820 Manual de usuario

Shuman

Shuman MC-250BT Manual de usuario

Stanton

Stanton STR8-150 Manual de usuario

Audio Technica

Audio Technica AT-LPW40WN Manual de usuario

Crosley

Crosley McQueen CR7011-GY Manual de usuario

Reloop

Reloop SMP-1 Manual de usuario

auna

auna TT-Classic Plus Manual de usuario

COMO AUDIO

COMO AUDIO Turntable Analog Manual de usuario

Dual

Dual 1009 F Manual de usuario

REED

REED Muse3C Manual de usuario

AXIOMTEK

AXIOMTEK OPS883-H Series Manual de usuario

Pioneer

Pioneer PL-71 Manual de usuario

Vestax

Vestax PDX-a1 Manual de usuario

Denon

Denon DP-400 Manual de usuario

Dual

Dual 504 Manual de usuario

Audio-Techica

Audio-Techica AT-LP60XBT Manual de usuario

Goldring

Goldring G99 Manual de usuario