Pro-Ject Audio Systems Jukebox E Manual de usuario

INSTRUCTIONS FOR USE

Pro-Ject Jukebox E

Jukebox E

Controls, features and connections

(1) TURNTABLE MOTOR SWITCH

(2) AMPLIFIER ON/OFF SWITCH

(3) REMOTE CONTROL

(4) INPUT SELECTOR, VOLUME CONTROL

(5) PLATTER

(6) DRIVE BELT

(7) STEPPED DRIVE PULLEY

(8) TONEARM COUNTERWEIGHT

(9) TONEARM TUBE

(10) TONEARM REST AND REMOVABLE TRANSPORT LOCK

(11) TONEARM LIFT LEVER

(12) HEADSHELL WITH FINGER LIFT

(13) TURNTABLE DISPLAY

(14) EARTH CONNECTION

(15) LINE OUTPUT

(16) PHONO OUTPUT

(17) LINE INPUT

(18) BLUETOOTH ANTENE

(19) SPEAKERS OUTPUT

(20) POWER SUPPLY SOCKET

(21) LID

(22) LID HINGE

(23) HINGE FASTENERS

POWER SUPPLY (NOT SHOWN) *

Dear music lo er,

Thank you for purchasing a record player from Pro-Ject Audio Systems.

In order to achie e maximum performance and reliability with this record player you should study these

instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

The following instructions for adjusting the cartridge are pro ided in case the cartridge is replaced by a

different model at a later date.

During assembly and adjustment of the deck small parts could be lost if not carefully placed in a

suitable receptacle. Before starting assembly make get fwqmiliar with the parts listed abo e and

correspondingly numbered in the technical drawings abo e. Separately packed items are marked with

an asterisk *.

Safety instructions

The power supply is used to connect and disconnect the unit from the mains. Make sure that the

plug is easily accessible at all times.

Hold the plug when unplugging the power cord. Ne er

handle the power cord while your hands are wet or damp.

A oid letting liquids enter the de ice. Ne er place any item containing liquid, like a flower ase,

on or near the de ice. Ne er spill any liquid on the de ice. Ne er place any naked flame sources,

like lighted candles, on or near the de ice. The product shall not be used in damp or wet locations,

next to a bathtub, sink, swimming pool or any other similar conditions.

Keep plastic bags away from children to pre ent any risk of suffocation.

Platter and drive belt installation

Please remo e brown paper insert which holds the platter in transport position. Put the felt mat on the

top of the platter. Install the dri e belt as shown in the following illustration.

Cartridge downforce adjustment

The counterweight (8) supplied is suitable for cartridges weighing between 3 - 7g (weight no. 81). The

counterweight is pre-set perfectly from the factory.

In case you need to set the tracking force, please read following instructions:

Place the stylus pressure gauge onto the platter

To adjust the amount of pressure, carefully mo e the

counterweight along the support rod, until the stylus pressure is sufficient to raise the pressure gauge

to the le el position. Mo ing the counterweight away from the cartridge will reduce pressure and

towards will increase pressure. Finally secure the counterweight using hexagonal key pro ided.

If the stylus gauge becomes le el, then the correct pressure has been achie ed. Howe er if the there is

insufficient or excessi e pressure the gauge will either not mo e or tilt down.

Connectors

Take care to connect the left and right channels correctly. The right channel is usually marked

red, the left channel black or white.

The red speaker terminals carry the positi e signal (+), the black speaker terminals the negati e

signal (–). Make sure the polarity of the connection is correct at each end of the cables.

Connection to the speakers

The output terminals accept loudspeaker cables terminated with 4mm ∅ Banana plugs, spades

connectors or naked wire.

ine output

A power amplifier or acti e loudspeakers can be connected to the output sockets marked Line OUT

(15).

Phono output

To use an external phono preamplifier, connect the RCA sockets marked Phono OUT (16). The

earthing wire may be connected to the screw terminal if you encounter hum problems when using the

turntable.

ine inputs

Line le el sources such as CD player, radio or TV can be connected to the input sockets marked In1

(17).

Mains power connection

Connect the low oltage plug from the power supply to the 24V socket (20) before connecting the

power supply to the mains.

Switching ON and OFF (turntable motor)

The rocker switch (1) on the bottom turns the motor of the turntable

To switch on from standby or to standby (amplifier)

The rocker switch (2) on the bottom turns the unit on or back into standby.

Control of the unit using the knob on the front

Standby

After the unit is powered on by the rocker switches on the bottom, pressing the knob for 3 seconds,

turns the unit on. For turn the unit back to standby press the knob again for 3 seconds

It is important to turn the unit to standby before it´s powered off by the switch on the bottom.

To not follow this step may cause damage to the speakers.

Input selector

After the unit is turned on, pressing the button in the middle selects desired input. After start

Bluetooth input is always selected. Pressing input button changes inputs in following order: Bluetooth

> Turntable > Line In. Bluetooth input gi es a “beep” sound when selected. Selected input is indicated

on the top line of the display.

Volume

Adjust the olume to the desired le el rotating the knob. Volume can be set in 33 steps (0-32) and is

indicated on the bottom line of the display

Remote control

red button turns the unit on or back into standby

Mute acti ate/deati ate mute

B ss+/B ss-/Treble+/Treble- tone control

Loudness acti ate/deacti ate Loudness

Bluetooth/Turnt ble/Line in direct access to

input

Volume+/Volume- adjust olume

Bluetooth connection

Bluetooth is acti e only when Bluetooth input is selected.

Juke Box E remembers last paired unit and reconnects automatically when a ailable and if the

bluetooth de ice allows automatic reconnections.

Juke Box E doesn´t request any pairing code confirmation.

Only one acti e Bluetooth connection is possible at a time. If the unit can’t be found in

Bluetooth search window in mobile de ice, make sure that there is no other acti e Bluetooth

connection.

Bluetooth input gi es 2 different “beeps”,

First appears when Bluetooth input is selected. And in case of Bluetooth de ice disconnects.

Second appear when Bluetooth de ice is found and connected.

P iring with Android devices

Open Settings and tap on Bluetooth. Turn on Bluetooth and tap on Sc n. Searched de ices will show

up. Tap on "Juke Box E".

P iring with Apple devices

Tap on Settings, tap on Bluetooth, turn on Bluetooth. Your de ice will automatically start searching

for a ailable de ices. Tap on "Juke Box E".

Fitting the lid

Fit the lid (dust co er) carefully o er the lid hinges (22) and adjust the screws (23) until the lid stays

open where you want it to without being too stiff to open or close.

Changing replay speed

Put the belt (6) o er the larger diameter part of the motor pulley (7). To re ert to 33 r.p.m. repeat the

proceedings using the smaller step on the pulley.

For detailed product information please refer to the Pro-Ject web site www.project- udio.com.

Maintenance and cleaning

Your record player requires little or no regular maintenance. Remo e dust with a slightly moistened

antistatic cloth. Ne er use a dry cloth because this will create static electricity which attract more dust!

Antistatic cleaning fluids are a ailable at specialist stores but must be applied sparingly to a oid

damage to rubber parts. It is recommended to fit the needle co er before cleaning or maintenance is

carried out to a oid damage.

If the player is not used o er a long period of time the dri e belt can be remo ed to pre ent unequal

stretching.

Always disconnect the record player from the mains power supply as a precaution before

maintenance!

Mounting and connecting the cartridge

** All cartridges with half inch mounting holes can be fitted. Lea ing the needle's protection co er on,

fit the cartridge to the headshell (14) using the screws supplied with the cartridge by passing one

screw through each slot in the headshell (14). Do not tighten the nuts yet.

Connect the tonearm wires to the cartridge pins as follows:

white left channel positi e (L+)

red right channel pos. (R+)

green right channel return (R -)

blue left channel return (L -)

The full sound quality of the record player can only be achie ed if the cartridge is correctly adjusted.

Particular tools like the Pro-Ject alignment tool “Align IT” are required to accomplish this job properly.

If you are not well acquainted with the adjustment of cartridges you are ad ised to call upon the willing

help of your Pro-Ject dealer to accomplish this task for you.

Please note: Adjusting a cartridge and tonearm calls for the greatest care in order to a oid

damaging the cartridge or tonearm bearings. Lea e this work to your dealer if you are in any

way unsure of the necessary steps and precautions to be taken.

Useful tips

The record player should be positioned on a low-resonance surface such as wood or multiple layer ply

board to a oid structural ibrations disturbing replay.

Technical specifications Pro-Ject Jukebox E / Pro-Ject 8.6 E

Turntable

Nominal speeds

3/45 r.p.m.

Speed ariance

3: ±0,80% 45: ±0,70%

Wow and flutter

3: ±0,29% 45: ±0,27%

Signal to noise -65dB

Effecti e tonearm mass

8,0g

Effecti e tonearm length

8,6" (218,5mm)

O erhang

2,0mm

Amplifier

Power output 2 x 50W at 4 ohms

SNR -75dB

Volume control 32 step

THD +N 0,5% at 1kHz, RL = 8 ohms, P = 1W

Crosstalk -80 dB

Phono amplifier Mo ing magnet (MM)

Phono gain: 43dB

Line le el inputs 2 pairs RCA

Amplifier gain 32 dB

Bluetooth 2.1 + EDR

Treble equalizer +- 12dB

Bass equalizer +- 12dB

General

Replacement battery remote control 2 x AAA

Power consumption 4,5W

Outboard power supply 24V/4A DC

Dimensions (W x H x D) 415 x 118 x 334mm

Weight 5,0kg

Dimensions packaging (W x H x D)

488 x 235 x 393mm

Weight incl. packaging 7kg

Potential incorrect use and fault conditions

Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls

before lea ing the factory. Faults that may possibly occur are not necessarily due to material or

production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore

the following list of common fault symptoms is included.

The platter doesn't turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Dri e belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or

from that to the phono box or between that and the amplifier. This could be due to a faulty plug,

broken wire or solder joint or simply loose plug/socket connection.

Phono input not selected at amplifier.

Amplifier is not switched on.

Amplifier or speakers are defecti e or muted.

No connection to the loudspeakers.

Strong hum on phono input:

No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.

Distorted or inconsistent sound from one or both channels:

Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.

Needle or cantile er damaged.

Wrong r.p.m., dri e belt o erstretched or dirty, platter bearing without oil, dirty or damaged

Service

Should you encounter a problem which you are not able to alle iate or identify despite the abo e

information, please contact your dealer for further ad ice. Only when the problem cannot be resol ed

there should the unit be sent to the responsible distributor in your country.

Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we

recommend keeping the original packaging.

Ne er return a record player without making sure that is it safely disassembled and correctly packaged

in the original packaging according to the diagrams on the last page of this user guide. Please remo e

these parts and pack them separately: lid, counterweight (4), anti-skating weight (10) and belt (22).

Fit the cartridge protection cap and the transport lock for the tonearm tube (66), prior to carefully

packaging the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these

instructions for use and/or by transportation without the original packaging. Modification or

change to any part of the product by unauthorized persons, release the manufacturer from any

liability o er and abo e the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademar

k of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

2017. All rights reser ed.

The information was correct at the time of going to

press. The manufacturer reser es the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical de elopment.

Tabla de contenidos

Otros manuales de Placa giratoria de Pro-Ject Audio Systems

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon DC Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Carbon Classic Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject 6 PerspeX DC Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems T1 Phono SB Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems VTA it Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Speed Box MK II Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Carbon Classic Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Classic Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension 12 Evolution Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut RecordMaster II Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 5 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems X1 Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems VT-E BT L Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Primary Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut PRO Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 6.1 SB SuperPack Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box Series Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems T2 W Manual de usuario

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box Esprit Manual de usuario

Manuales populares de Placa giratoria de otras marcas

Gemini

Gemini CDT-05 MKII Manual de usuario

Rotel

Rotel RP-820 Manual de usuario

Shuman

Shuman MC-250BT Manual de usuario

Stanton

Stanton STR8-150 Manual de usuario

Audio Technica

Audio Technica AT-LPW40WN Manual de usuario

Crosley

Crosley McQueen CR7011-GY Manual de usuario

Reloop

Reloop SMP-1 Manual de usuario

auna

auna TT-Classic Plus Manual de usuario

COMO AUDIO

COMO AUDIO Turntable Analog Manual de usuario

Dual

Dual 1009 F Manual de usuario

REED

REED Muse3C Manual de usuario

AXIOMTEK

AXIOMTEK OPS883-H Series Manual de usuario

Pioneer

Pioneer PL-71 Manual de usuario

Vestax

Vestax PDX-a1 Manual de usuario

Denon

Denon DP-400 Manual de usuario

Dual

Dual 504 Manual de usuario

Audio-Techica

Audio-Techica AT-LP60XBT Manual de usuario

Goldring

Goldring G99 Manual de usuario