Pro-face FP-790T Manual de usuario

Flat Panel Display

FP-790T

User Manual

Digital Electronics Corporation

FP-790T User Manual 1

1) It is forbidden to copy the contents of this manual, in whole or in part, except for the

user's personal use, without the express permission of the Digital Electronics Corporation

of Japan.

2) The information provided in this manual is subject to change without notice.

3) This manual has been written with care and attention to detail; however, should you find

any errors or omissions, please contact the Digital Electronics Corporation and inform

them of your findings.

4) Please be aware that the Digital Electronics Corporation is not responsible for any dam-

ages resulting from the use of our products, regardless of article 3 above.

<Note>

Thank you for purchasing Digital's TFT type color display panel, the 'FP-790T'(hereafter referred

to as "the FP").

The FP is a TFT type color liquid crystal display monitor for Windowscompatible personal

computers (VGA, XGA and SVGA modes).

Please read this manual completely to insure the correct use and complete understanding of the

FP's functions.

The FP's analog interface is designed to comply with VESA standards. Please be aware that this

unit may not be able to be connected with devices using nonstandard VGA interfaces. For

further information, please refer to this chapter's "PC Connection Notes" section.

Preface

All Company/Manufacturer names used in this manual are the registered trademarks of their

respective companies.

FP-790T User Manual2

• To avoid the possiblity of an electric shock, be sure to connect the power

cord to the FP before connecting it to the main power supply.

• A fire or electrical shock may occur if voltages used with the FP are beyond

the specified range. Be sure to use only the specified voltage.

• Before opening the FP's protective cover, be sure to turn the units power

OFF. This is because the FP's internal parts carry high voltages.

• To avoid fires or electrical hazards, do not modify the FP in any way.

• Do not create touch panel switches that are used to either control or to

ensure the safety of equipment and personnel. Mechanical switches, such

as an emergency stop switch, a deadman (two-handed) start switch, etc.,

must be installed and operated via a separate control system.

• Do not create touch panel switches which could possibly endanger the safety

of humans and equipment. This is due to the possibility of a malfunction in

the FP or its cable(s), causing the output of a signal that could result in a

major accident. All of a system’s major, safety-related switches should be

designed to be operated separately from the FP.

This section describes the safety precautions necessary for the correct use of the FP.

Please keep this manual close at hand and refer to it when necessary.

Safety Icons

The following symbols are used throughout this manual to ensure the safe use of the

FP. Please be sure to follow all instructions given since they explain important safety

points.

Essential Safety Precautions

This mark warns of a situation that could cause

either serious or fatal injury if the instruction is

ignored and/or the unit is used incorrectly.

This mark warns of a situation that could cause

either personal injury or property damage if the

instruction is ignored and/or the unit is used

incorrectly.

Warning

Cautions

WARNINGS

FP-790T User Manual 3

WARNINGS

• After the FP's backlight burns out, unlike the FP's "Standby Mode", the touch

panel is still active. If the operator fails to notice that the backlight is burned

out and touches the panel, a potentially dangerous machine operation

mistake can occur.

If your FP's backlight suddenly turns OFF, use the following steps to

determine if the backlight is actually burned out.

1)If your FP is not set to "Standby Mode" and the screen has gone blank,

your backlight is burned out.

2)Or, if your FP is set to Standby Mode, but touching the screen does not

cause the display to reappear, your backlight is burned out.

• If metal particles, water or other types of liquids contact any of the FP's

internal parts, immediately turn the units power OFF, unplug the power cord,

and contact either your FP distributor or the Digital Electronics Corporation.

• Read and understand Chapter 3 "Installation and Wiring" thoroughly in order

to select an appropriate installation location for the FP.

• Before either plugging in or unplugging a board or interface connector, be

sure to turn the FP's power OFF.

• To prevent a possible explosion, do not install the FP in areas containing

flammable gases.

• The FP is not appropriate for use with aircraft control devices, aerospace

equipment, central trunk data transmission (communication) devices, nuclear

power control devices, or medical life support equipment, due to these

devices inherent requirements of extremely high levels of safety and

reliability.

• When using the FP with transportation vehicles (trains, cars and ships),

disaster and crime prevention devices, various types of safety equipment,

non-life support related medical devices, etc. redundant and/or failsafe

system designs should be used to ensure the proper degree of reliability

and safety.

FP-790T User Manual4

About the FP's Display Panel

•The FP's currently displayed data, its voltage and brightness setting each affect the intensity

of Contouring. (i.e, when some parts of the screen are brighter than others, creating a

wavelike pattern)

•There are minute grid-points (dark and light) on the Display Panel's surface. This is part of

the FP's design and not a defect.

•Shadows may appear at the top of the LCD. This is normal for an LCD display.

•Sometimes the display area may look as if the display colors have changed. This is a

common attribute of LCD's and is not a defect.

•Displaying a single image for long periods can cause an afterimage to remain when the

display is changed to another screen. To prevent this, periodically turn the FP OFF and

then ON again to remove this afterimage.

• Do not push on the FP’s screen too strongly, with either your finger or with a

hard object. Excessive pressure can scratch, crack or damage the screen.

• Do not use a pointed object, such as a mechanical pencil or screw-driver, to

press any of the touch panel’s switches, since they can damage the display.

• If the screen becomes dirty or smudged, moisten a soft cloth with diluted

neutral detergent, wring the cloth well, and wipe the display. Do not use thin-

ner or organic solvents.

• Avoid exposing the FP to, or operating the FP in direct sunlight, high tem-

peratures and humidity, and in areas where excessive dust and vibration will

occur.

• Avoid using the FP in areas where sudden, extreme changes in temperature

can occur. This may cause con-densation to form inside the unit, possibly

leading to an accident.

• To prevent the FP from overheating, be sure its air circulation vents are clear

and clean, and keep the unit’s operation area well-ventilated.

• Avoid operating or storing the FP near chemicals, or where chemicals can

come into contact with the unit.

CAUTIONS

FP-790T User Manual 5

Table of Contents

Preface ...................................................................................................................................... 1

Essential Safety Precautions ............................................................................................................ 2

Table of Contents .............................................................................................................................. 5

CE Marking Notes ............................................................................................................................ 7

PC Connection Notes ........................................................................................................................ 7

FP-790T Features.............................................................................................................................. 8

Package Contents .............................................................................................................................. 9

Symbol Information........................................................................................................................ 10

Chapter 1—Introduction

1-1 Connecting the FP to a PC .....................................................................................................1-1

1-2 Optional Equipment ...............................................................................................................1-3

Chapter 2—Specifications

2-1 General Specifications ............................................................................................................2-1

2-1-1 Electrical Specifications.................................................................................................2-1

2-1-2 Structural Specifications ................................................................................................2-1

2-1-3 Environment Specifications ...........................................................................................2-2

2-1-4 Touch Panel Specifications ............................................................................................2-2

2-1-5 External Interface Specifications ...................................................................................2-3

2-2 Functional Specifications .......................................................................................................2-3

2-2-1 Display Specifications....................................................................................................2-3

2-3 Interface Specifications ..........................................................................................................2-4

2-3-1 Analog RGB Interface....................................................................................................2-4

2-3-2 RS-232C Interface ..........................................................................................................2-5

2-3-3 Mouse Connector ...........................................................................................................2-6

2-3-4 Mouse Type Host Connector..........................................................................................2-6

2-4 Option Cable Pin Diagrams...................................................................................................2-7

2-5 Parts Names and Functions ..................................................................................................2-9

2-6 Dimensions ...........................................................................................................................2-10

2-6-1 FP-790T External Dimensions .....................................................................................2-10

2-6-2 Installation Fasteners....................................................................................................2-11

2-6-3 Panel Cut Dimensions ..................................................................................................2-10

FP-790T User Manual6

Chapter 3—Installation and Wiring

3-1 Installation ...............................................................................................................................3-1

3-1-1 Installation Procedures ...................................................................................................3-1

3-2 Wiring ...................................................................................................................................3-4

3-2-1 Power Cable Connection Precautions ............................................................................3-4

3-2-2 FP Power Cable Connection Procedures .......................................................................3-6

3-2-3 FP Power Supply Connection Procedures .....................................................................3-7

3-2-4 FP Grounding Cautions ..................................................................................................3-7

3-2-5 FP Input/Output Signal Line Cautions...........................................................................3-7

3-3 Setup of Operation Mode and Positioning of Display.........................................................3-8

3-3-1 Operation Mode Setup and Adjustment.........................................................................3-8

3-4 Screen Adjustment using OSD ............................................................................................3-10

Chapter 4—Touch Panel Commands

4-1 Command List .........................................................................................................................4-1

4-2 Touch Panel Data Input..........................................................................................................4-3

4-3 Boot-up Initialization..............................................................................................................4-7

Chapter 5—Troubleshooting

5-1 Troubleshooting.......................................................................................................................5-1

5-1-1 Possible Device Problems ..............................................................................................5-1

5-1-2 No Display......................................................................................................................5-2

5-1-3 The Touch Panel Does Not Function .............................................................................5-4

Chapter 6—Maintenance

6-1 Cleaning the FP's Display ......................................................................................................6-1

6-2 Periodic Check-Up ..................................................................................................................6-2

6-3 Changing the Backlight ..........................................................................................................6-3

FP-790T User Manual 7

CE Marking Notes

The FP's analog RGB interface offers normal display performance within the

following ranges:

Since some commercially-available video interface equipment also accomodates

tracking ranges in excess of those shown above, they may not offer normal display

performance when used with the PC. Before using a video interface, be sure to

check its specifications.

Also, even if the same type personal computer is used to transfer data to the PC,

the above mentioned problems can also occur when the PC's video board is

replaced.

While the FP('s OS) is starting up, please do not touch the screen's touch panel.

PC Connection Notes

VESA standard

displaymode Size Horizontal

frequency Vertical

frequency Dot clock

frequency SyncLogic

V.H

31.469kHz 59.992Hz 25.175MHz -,-

37.500kHz 75.000Hz 31.500MHz -,-

37.879kHz 60.317Hz 40.000MHz +,+

46.875kHz 75.000Hz 49.500MHz +,+

48.363kHz 60.004Hz 65.000MHz -,-

56.476kHz 70.069Hz 75.000MHz +,+

60.023kHz 75.029Hz 78.750MHz +,+

31.469kHz 70.087Hz 28.322MHz +,-

37.927kHz 85.039Hz 35.500MHz +,-

640×480

800×600

1024×768

720×400

VGA

SVGA

XGA

USText

The FP-790T is a CE marked, EC compliant product.

Safety (EN60950)

EMI (EN55011 class A), EN61000-3-2, EN61000-3-3

EMS (EN61000-6-2)

• The allowable frequency fluctuation range in both the horizontal

and vertical frequencies is +/- 1%. If fluctuations exceed these

ranges, the FP will enter power save mode and the display will go

blank.

• Be sure to turn FP-790T and PC ON at the same time, or before

turning PC ON. If PC is turned ON first, a touch panel and an exter-

nal mouse will not work.

FP-790T User Manual8

•Large-sized, high-quality color LCD

The monitor uses a 14.1 inch TFT type color LCD, and the 260,000 display colors

allow a wide variety of screen designs. The features of this display are easy-to-

read images and text, wide view angle, high contrast, and fast response.

•FP's large-sized display is XGA mode compatible

The FP is compatible with XGA mode, allowing a large variety of information to

be displayed.

•Display mode is automatically selected (Multi-scan)

The FP's multi-scan feature automatically selects the display mode, according to

the host’s display mode (VGA, SVGA, XGA or US Text).

•PC data can be displayed on the FP

Since the FP is connected to the host through an analog RGB interface, it can also

be easily connected to a personal computer and used as a display.

For the available display modes, see “PC Connection Notes”

•Rear-mounting type is designed to be built into other equipment

The slim and compact body is designed specifically to be built into machine cabinets

and panels. Since the FP can be easily used with other equipment, it can be used as

a monitor for your PC-based Industrial Automation system. Also, the FP front

panel's installation gasket provides a dust and drip-resistant seal between the FP's

front face and the installation panel. Thus, the FP can be used even in harsh industrial

environments.

• Touch panel can be operated while PLC data is monitored (Standard feature)

The FP's touch panel is standard equipment and is suitable for monitoring systems

that require touch operations.

FP-790T Features

FP-790T User Manual 9

The FP's packing box contains the items listed below. Please check to be sure each is

included and is not damaged.

FP unit (FP790-T21)

CD-ROM *1 Installation brackets (12)

(contains the PDF manuals) <GP070-AT01>

Package Contents

FP-790T Installation Guide

FP-790T

Installation

Guide

These items have all been carefully packed with special attention to product quality.

However, should you find any item(s) damaged or missing, please contact your local

distributor immediately for prompt service.

Installation gasket

<FP790-WP00>

*1 For description and usage of the application programs stored in the floppy disk, see

that disk's English “READ_ME.DOC” file.

Tabla de contenidos

Otros manuales de Monitor de Pro-face

Pro-face

Pro-face GP577R-TC11 Manual de usuario

Pro-face

Pro-face PL-X900 Series Manual de usuario

Pro-face

Pro-face GP-3600T Series Manual de usuario

Pro-face

Pro-face GC4000 Series Manual de usuario

Pro-face

Pro-face Xycom SXT1811 Instrucciones de instalación

Pro-face

Pro-face FP3900-T41 Manual de usuario

Pro-face

Pro-face GP77R Series Manual de instrucciones

Pro-face

Pro-face GP-3750T Manual de usuario

Pro-face

Pro-face SP5000 Series Manual de usuario

Pro-face

Pro-face FP2650-T41 Manual de usuario

Pro-face

Pro-face SP-5600TP Manual de usuario

Pro-face

Pro-face GP-3300T Manual

Pro-face

Pro-face PS-3000B Series Manual de usuario

Pro-face

Pro-face GP-4201TM Manual de usuario

Pro-face

Pro-face FP3650-T41 Manual de usuario

Pro-face

Pro-face GP-4000M Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación