Pro-Elec PEL00562 Manual de usuario
2.0kW Oil Filled Radiator with Timer
Model: PEL00562
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future
reference.
• When using electrical appliances basic safety precautions should always be
followed.
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
• The appliance must be used on a stable surface.
• In order to avoid overheating do not cover the heater.
• This appliance is intended for domestic use only. It should not be used for
commercial purposes.
• Do not use the appliance for any purpose other than that for which it is designed.
• Always turn the product to the OFF position and unplug it from the electrical outlet
when not in use.
• The heater must not be located immediately below an electrical socket-outlet.
• Do not operate the heater with a damaged cord or plug, or after the heater
malfunctions, has been dropped, or damaged in any manner.
• If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualied person to avoid a hazard.
• This heater is lled with a precise quantity of oil. Repairs requiring the opening of
the oil container are only to be made by the manufacturer or his service agent who
should be contacted if there is an oil leak.
• This appliance contains no user-serviceable parts.
• When scrapping the heater, follow the regulations concerning the disposal of oil.
• Don’t use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
• Never locate the heater where it may fall into bathtub or other water container.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
• The appliance must be unplugged from the power supply after use and whilst any
maintenance such as cleaning is carried out.
CAUTION - Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
PRODUCT OVERVIEW
1. Carry Handle
2. Indicator Light
3. Power Switch
4. Adjustable Thermostat
5. Timer
6. Power Cord Storage
7. Fin Body
8. Castor
Models with built in timer
ASSEMBLY INSTRUCTIONS
• The heater is packaged with the feet unattached. You must attach them before
operating the heater.
WARNING: Do not operate without feet attached. Only operate the heater in an upright
position (feet on the bottom, controls on the top), any other position could create a
hazardous situation.
1. Place the radiator body upside-down on a scratch-free location, make sure it is
stable and will not fall.
2. Remove the wing nuts from the U-bolt provided (see Fig 1), insert the U-shaped
bolt around the ange between rst pair of ns (near the front cover) (see Fig 2).
3. Insert the threaded ends of the U-bolt through the holes on the castor mounting
plate (see Fig 3).
4. Screw the wing nuts back on to the U-bolt and tighten (see Fig 4).
5. Repeat with the rear castor inserting the U-bolt between rearmost pair of ns
Note: do not over-tighten, as this may cause the damage of radiator ange.
6. Unscrew the nut from the castor, and insert through the end hole in the mounting
plate and ret the nut.
7. Repeat for all four castors then tighten the nuts.
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste
Electrical & Electronic Equipment (WEEE). Any WEEE marked products
must not be mixed with general household waste, but kept separate for the
treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man ReV.1.0
INSTRUCTIONS FOR USE
• Before using the heater, make sure that it is on a at and stable surface. Damage
may occur if it is placed on an incline or uneven surface.
• Set all the controls to OFF position and insert the plug into a mains socket
• Rotate the thermostat knob clockwise to MAX position and switch the heater on.
• The power switch has three heat settings I, II and III, power on is indicated by a
LED.
• When your room reaches the desired temperature, slowly rotate the thermostat
control counter clockwise until the pilot light goes out. The thermostat can now be
left at this setting. As soon as the room temperature has dropped below the set
temperature, the unit will switch it self on automatically until the set temperature
has been reached again. In this way the room temperature remains constant with
the most economical use of electricity.
• If you want to change the room temperature setting, rotate the thermostat knob
clockwise to raise the temperature, or counter clockwise to lower it.
• This heater includes an overheat protection system that shuts off the heater when
parts of the heater are getting excessively hot.
• To completely shut the heater off, turn power switch to OFF (O) and remove the
plug from the mains socket.
• If the heater is to remain unused for long periods, wind the cable around the cable
storage boss and store the heater in a clean dry place.
CLEANING AND MAINTENANCE
• Always remove the plug from the mains socket and allow the radiator to cool down
before cleaning the heater.
• Wipe the radiator with a soft damp (not wet) cloth.
• Do not use any cleaning chemicals such as detergents and abrasives.
• In case of malfunction or doubt, do not try to repair the radiator yourself, it may
result in a re hazard or electric shock.
USING THE TIMER
• Set the timer by adjusting the clock wheel so that the arrow points to the current
time.
• Set the slide switch position to the clock setting.
• Set the time periods required for heating by pushing the red teeth outwards.
• Each tooth represents 15 minutes.
• Pushing the teeth back to the centre will turn the heater off for that period. To run
the heater continuously set the slide switch to the I position.
Tabla de contenidos
Otros manuales de Calentador de Pro-Elec
Pro-Elec
Pro-Elec PEL00940 Manual de usuario
Pro-Elec
Pro-Elec PEL0065 Manual de usuario
Pro-Elec
Pro-Elec PEL00922 Manual de usuario
Pro-Elec
Pro-Elec PELL0211 Manual de usuario
Pro-Elec
Pro-Elec PEL00558 Manual de usuario
Pro-Elec
Pro-Elec PELL0209 Manual de usuario
Pro-Elec
Pro-Elec PEL00920 Manual de usuario
Pro-Elec
Pro-Elec PEL00939 Manual de usuario
Pro-Elec
Pro-Elec PELL0214 Manual de usuario
Pro-Elec
Pro-Elec PEL00570 Manual de usuario
Pro-Elec
Pro-Elec PEL00939 Manual de usuario
Pro-Elec
Pro-Elec PEL00941 Manual de usuario
Pro-Elec
Pro-Elec PELL0208 Manual de usuario
Pro-Elec
Pro-Elec PELL0205 Manual de usuario
Pro-Elec
Pro-Elec PELL0214 Manual de usuario
Pro-Elec
Pro-Elec PELL0216 Manual de usuario
Pro-Elec
Pro-Elec PEL00923 Manual de usuario
Pro-Elec
Pro-Elec PELL0215 Manual de usuario
Pro-Elec
Pro-Elec PELL0203 Manual de usuario
Pro-Elec
Pro-Elec PELL0410 Manual de usuario
Manuales populares de Calentador de otras marcas
Empire Heating Systems
Empire Heating Systems WCC65 Manual de usuario
Wetekom
Wetekom 92 86 43 Manual de usuario
Desa
Desa SPC170-F Manual de usuario
Watlow
Watlow Watrod Electric Tubular Heaters Manual de usuario
Haverland
Haverland ECO-DRY GPS Series Manual de lista de piezas
Stelpro
Stelpro ASILVC2060 Series Manual de usuario