Prince T8840 Manual de usuario
O W N E R ' S M A N U A L
2L-4239-00
2015 Escalade Sports
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
TABLE TENNIS TABLE
MODEL NUMBER
T8840
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
Please Do Not Return This Product To The Store!
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 2 to identify and sort all fasteners. Check all
cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may
not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 3/8” Wrenches, Two 7/16” Wrenches (Ratchet and 3/8”, 7/16”
Sockets are recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could
over-tighten the and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be
contacted for replacement parts.
Sorting your hardware ahead of time will speed up assembly time. Sort all your
hardware now so it will be ready before you start assembly.
NOTE:
A. An electric screwdriver is helpful in assembly. However, please set to low torque and
use caution because you could over-tighten the hardware and strip the screws.
B. Indentation mounting guides are small so look closely when attaching hardware.
C. Table top can be set on top of two saw horses. Although this will make assembly easier
it is not necessary to complete assembly. Always use shipping container to protect the painted
surface of the table top.
CAUTION: Make sure that the table top is secure on sawhorses and NEVER leave
the table top unattended.
ASSEMBLY TIPS
2
(Qty. 6)
1/4-20 Zinc
Locknut
(Qty. 24)
(Qty. 2)
(Qty. 4)
(Qty. 2)
(Qty. 4) (Qty. 4)
(Qty. 6)
(Qty. 100)
(Qty. 16)
(Qty. 4)
(Qty. 4)
S.M.S. (Qty. 4)
#8 x 1 7/16
Sheet Metal Screw
(Qty. 12)
1/4-20 x 3 1/4 Hex Head Bolt
37
38
1/4-20 x 2 1/4 Hex Head Bolt
(Qty. 4)
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 4)
1/4-20 x 2 1/2 Hex Head Bolt
(Qty. 2)
39
Not UsedNot Used
2. Align U-Support (#7) on Table Top as shown in Figure 1.
1. Lay Table Top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
1
7
Note: Indentations are
small so look closely.
End Rail Mounting
Indentations
Note: Indentations are
small so look closely.
ASSEMBLY TIP
Table top can be set on two saw horses. Although this will make
assembly easier it is not necessary to complete assembly. Always use
shipping container to protect the painted surface of the table top.
CAUTION: Make sure that the table top is secure on the
sawhorses and NEVER leave the table top unattended.
ASSEMBLY TIP
The following pages will have a picture of the
Hardware Needed (to scale) along with the
Quantity, Key# and Description. You can lay the
hardware on the picture to identify the hardware.
Figure
3
20
3
IMPORTANT:
Slot in
U-Clip
End Rail Mounting
Indentations
Detail A
3. Align the holes in the U-clips #3 with Indentations in table top
assembly and secure with twelve screws #20 as shown. All four
holes in each U-Clip must align with four Indentations in top.
See Figure 2 and Detail A.
Be sure that slot in the three U-clips #3 all face the
same direction as shown. (Toward the end of the
table with no stripe.)
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS
(#3) BE TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY,
YOU WILL DO IRREPARABLE DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT
TO OPEN IT TO THE PLAYING POSITION.
CAUTION:
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
CAUTION:
20
HARDWARE NEEDED
#8 X 7/16” Screw
(Qty. 12)Figure
4
34
33
20
20
Detail B
4. Align the holes in the Mounting Brackets #33 & #34 with
Indentations in table top assembly and secure with screws #20
as shown. All holes in each Mounting Bracket must align with
Indentations in the top. See Figure 3 and Detail B.
Note: Indentations
in table top are small
so look closely.
Figure
20
HARDWARE NEEDED
#8 X 7/16” Screw
(Qty. 20)
5
5. Attach Legs (#2) to Mounting Bracket (#34) with Hex Bolt (#38),
two Plastic Washers (#24) and Locknut (#15). Attach leg brace
to Leg Mounting Bracket (#33) with Phillips Head Screw (#37)
and Locknut (#16) as shown in Detail C.
6. Attach Leg Plugs (#13) to bottom of the Legs (#2) as shown in
Figure 4.
24 15
16 37
2
Leg Brace
38
33
34
Detail C
13
24
Plastic Washer
(Qty. 4)
15
1/4” Locknut
(Qty. 2)
37 #10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 2)
38
#10-24 X 1/2 Locknut
(Qty. 2)
16
1/4-20 x 2 1/4 Hex Head Bolt
(Qty. 2)
Figure
HARDWARE NEEDED
6
Note: Legs not
shown for Clarity
19
3
7
Detail D
7
Note: Rotate U-Support #7 until you see the screw
hole in the slot of U-clip #3. Slide U-support #7
side to side and front to back if necessary.
7. Insert Screw #19 through slot in U-Clip #3 and
into U-Support #7. Thread it all the way into U-
Support #7 until it touches the back of the tube.
There should be about 3/8 inch of screw #19 left
sticking out. DO NOT insert screw#19 in middle
#3 U-Clip. See Figure 5 & Detail D.
If you want to see a video on how to insert Screw (#19) go to:
http://www.escaladesports.com/customer-service/videos.html
Or
Scan with your smartphone:
Note: Rotate U-Support #7 until you see the screw hole in the
slot of U-clip #3. Slide U-support #7 side to side and front to
back if necessary.
Note: To aid in assembly use a cordless drill and Phillips bit, but be
careful to not strip the screws. Wear safety glasses for Step 7.
Figure
20
19
HARDWARE NEEDED
#8-32 X 1 1/4
Phillips Head Screw
(Qty. 2)
DO NOT insert Screw
#19 in middle #3 U-clip.
7
10. Line up holes in rails with indentations in
top and secure using eighteen screws
#20. See Figure 6 & Detail E1 & E2.
26
25
20
Shorter Distance
Longer Distance
35 (RH)
Note: Legs not
shown for Clarity
8. Lay out Right Side Rails #25, Left Side Rails
#29 and End Rails #26, around edges of
table top as shown in Figure 6.
20
9. Slide Left #36 and Right #35 Vinyl End
Caps onto the ends of the Side Rails #25
& 29 as shown in Detail E1 & E2.
Detail E2
11. Lay Corner Caps #22 on table as shown
in Figure 6. If Corner Cap sticks above
the table top surface of the table, flip
over so shorter distance is against edge.
Secure to bottom of table with three
Screws #21. See Detail F.
Detail F
Note: Rails attach
with #20 screws
20
Note: U-Support not
shown for Clarity
(RH Rail)
Note: Prince
logo must be on
this end of Rail.
(LH Rail)
29
Note: Prince
logo must be on
this end of Rail.
21
#8 x 1 7/16
Sheet Metal Screw
(Qty. 6)
#8 x 7/16
Sheet Metal Screw
(Qty. 18)
HARDWARE NEEDED
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
CAUTION:
8
36 (LH)
20
Detail E1
7
4
23
4
15
31
2
Detail H
First Table Top
Figure 7A
Important! DO NOT put other
safety strap #6 on this table
half. It will be installed on
second table half later.
15
1/4” Locknut
(Qty. 3)
39 1/4-20 x 2 1/2 Hex Head Bolt
(Qty. 1)
1/4-20 x3 1/4 Hex Head Bolt
(Qty. 2)
30
3/4” Spacer
(Qty. 2)
31
5/16” Spacer
(Qty. 2)
HARDWARE NEEDED
24 Plastic Washer
(Qty. 2)
1/4-20 x 1 1/2 Bolt
(Qty. 1)
9
HARDWARE NEEDED
30
6
4
24
15
9
Detail G1 31
2
4
15
39
6
30
15
24
Detail G2
(Longer)
23
(Longer)
Note: This is the end of the
table with no rails.
14. Attach slotted end of safety strap #6 to INSIDE of Leg #2
using one bolt #39, one spacer #30, one washer #24,
and one hex nut #15. Tighten hardware until snug but do
not overtighten. Tubes must pivot freely. See Detail G2.
12. Attach safety strap #6 to linkage #4. Be sure to attach on the end of
linkage with TWO holes. Use one bolt #9, one washer #24, one
Spacer #30, and one hex nut #15. See Detail G1.
13. Attach end of linkage #4 with the attached Safety Strap #6 INSIDE of
Leg #2 as shown in Detail G2. Secure through end hole with bolt
#23, Spacer #31 and locknut #15. Tighten hardware snug enough to
keep table stable but do not overtighten. Tubes must pivot freely.
15. Attach linkage #4 INSIDE other Leg #2 as shown in
Detail H. Secure through end hole with bolt #23,
plastic spacers #31 and locknuts #15. Tighten
hardware snug enough to keep table stable but do
not overtighten. Tubes must pivot freely.
9
2
Figure 7B
First Table Top
16. Gently tap caster sockets #12 into U-
support #7 until flange on sockets
touches the edge of the tube.
17. Insert casters #11 into caster sockets
#12. See Figure 7B.
DO NOT HIT CASTER SOCKET #12 DIRECTLY WITH
A HAMMER! SET A PIECE OF WOOD ON CASTER
SOCKET AND HIT PIECE OF WOOD TO DRIVE
CASTER SOCKET INTO U-SUPPORT #7.
NOTE:
11
12
7
Note: This is the end of the
table with no rails.
10
Tabla de contenidos
Idiomas:
Otros manuales de Robótica de Prince
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
