Premiertek POWERLINK PT-AP2403 Manual de usuario

2.Configuration before application

For Windows Vista or Windows 7 system, please follow the steps below to setup

1Click “Start Control Panel Network

and Internet Network and Sharing

Center Change adapter settings

Local Area Connection” Select “Wireless

Network Connection”, right-click it and

select “Properties”

→ →

→

→ → 2Select “Internet Protocol Version 4

(TCP/IPv4)” and click “Properties” 3Set IP address as 192.168.16.X(X should be

a numeral between1 to 253), subnet mask as

255.255.255.0, then click “OK” to return back

the last page, click “OK” once again.

VER:1.0

A.Local network settings

2Select an item in the “Wireless Network

Connection” list to connect a wireless

network, and then click "connect"

1An icon of “ ”will appear at the

bottom corner of your computer after

installation of this pocket router , then

click the icon

right

B.Wireless settings

3When there shows "Connected" on the screen,

it means your computer has accessed to

wireless network successfully

http://192.168.16.254

1.Open the web browser, input the default address: 192.168.16.254

in address bar, then press “Enter”

2.Input user name and password, default value are all “admin”, and

then click “OK”

C.Login the wireless router Web Server

If the Base Station (BS) is encrypted, then please input the password. It turns out to be a green icon “ ” if connected successfully

When works in AP mode, there are two operating modes:

Wireline connection and wireless connection

Mini Travel Router

POWER L AN WIF I

RT Cl ien t AP

POW ER L AN W IF I

RT Clien t AP

1.Log in the management interface, spread "wireless network settings" item

on the left menu and click "AP client"

In AP mode,choose "enable" option in the drop-down list, then click "enable"

button to enable client function

(Please note that under condition of exchanging wireline to wireless access, it is better to disable

“AP client” function)

2.Click “Site Survey” of the menu on the left, select the connecting access point and

then click “connect”

Click “scan” if the connecting access point is not on the list

3.Information of system wireless access point will appear automatically,

if your wireless access point is encrypted,You only need to set the same

"Encryption Type" and "Pass Phrase"of the two devices .

4.Menu turns out to be as follows if connected successfully

!!Tip:

After you connect the wireless successfully through web management of this device, please re-configure the Local Area Network IP address of the computer according to

the connected wireless access point. If the connected wireless network can assign the IP address to users dynamically, then set the IP and DNS address of the computer

as “Obtain an IP address automatically” and “Obtain DNS server address automatically”If it requires static IP, then you can only access the company(home)LAN or Internet

by setting the IP address and DNS address of the computer according to real application.

3.Operation mode configuration

AP mode

Exchange of wireline access to wireless access configuration

When the wireless hotspot cannot cover effectively, you can also connect to Wireless Pocket

Router by wired connection or wireless connection way. log in the management interface and

configure according to steps on the right, then connect to the existing wireless hotspot.making

POWER L AN WIF I

RT Cl ien t AP

POW ER L AN W IF I

RT Clien t AP

Switch

Wireless signal amplification/relay settings

It is plug and play for this application, there's no need to configure on management interface. Connect the

cable from switch of wired internet with the Ethernet port of this pocket router, with power supply it will start

working.

Inte rne t Proto col Version 4 (TC P/IP v 4) Properties

General Al terna tive co nfigu ratio n

You ca n get IP setti ngs ass igned automatic ally if your networ k suppor ts

this c apabi lity, Other w ise, you nee d to ask your netw ork adm inistrator

for th e appro priat e IP sett ings.

Obta in an I P addre ss automat ically

Use th e fol lowing IP ad dress:

Obta in DN S ser ver address automa tically

Use th e fol lowing DNS serve r addre ss:

Validat e set tings u pon exit Advanced...

OKCancel

IP adress:

Subnet ma sk:

Defa ult g atewa y:

Preferred DNS ser ver :

Alte rnate D NS se r ver :

？

Wireles s Netwo rk Connec tion Prop erties

This c onnec tion uses th e follo wing it ems:

Clie nt for Mi crosoft Netw orks

QoS Packet Sch eduler

File a nd Prin ter Sha ring for Micro soft Ne twork s

Internet Protocol Ver sion 6 (TC P/IP v 6)

Link -L ayer Topolo gy D iscov er y Map pe r / I O Dri ver

Link -L ayer Topolo gy D iscov er y Respo nder

Insta l...Uninstall Properties

Tran smissio n Control Pro to col/Int er net Protoco l. The defa ult

wide are a ne twork proto col that provde s communi catio n

across div erse in te rc onnecte d network s.

Descn ption

OKCanc el

Connect using:

Networking

Configure...

802.11n USB Wireless LAN Card

Internet Protocol Ver sion 4 (TC P/IP v 4)

Wirel ess Network Connection

WA01

WP03-N1

WH01-G1

WP02

Open Netw ork a nd Sh aring Center

WH02-G2

MG02

MP01

Internet access

Connected

8:08

2011-09-18

)

MP01

Open Netw ork a nd Sh aring Center

8:08

2011-09-18

)

Not connected

Connect ion s are a vailable

Wirel ess Network Connecti on

MP01

Info rma tion sent ov er th is netw ork

migh t be vi sible to oth ers .

Connect automatiically Connect

WA01

WP03-N1

WH01-G1

WP02

Wirel ess Network Connection

WA01

WP03-N1

WH01-G1

WP02

Open Netw ork a nd Sh aring Center

WH02-G2

MG02

8:08

2011-09-18

)

MP01

Not connected

Connect ion s are a vailable

Wireless Network Connection

Acquiring network address

802.11n USB Wire less Lan

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Prope r tie s

Connect/Disconnect

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Basic

Advanced

Security

WDS

WPS

Administration

AP Client

Site Sur vey

Station List

AP Setting

You could turn on or turn off AP Client feature

AP Client feature Settings

AP Client E nabled

Apply Cancel

AP Client Parameter

SSID

MAC Address (Optional)

Security Mode

BL-WA02

48:02 :2a :80 :38:20

WPA2 -PSK

Encryption Type

AES

Pass Phrase

Tt&13 1 4s e

Apply Cancel/Refresh

Save

OKCancel

Remember my credentials

admin

●●●●●

The ser ver 192.168.16.254 at Welcome to Wireless 11N router requires a

username and password.

Warning:This server is requesting that your username and password be

sent in an insecure manner(basic authentication without a secure

connection).

Window Security

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Basic

Advanced

Security

WDS

WPS

Administration

AP Client

Site Survey

Station List

Connect sc an

Site Survey

SSID BSSID RSSI Channel Encr yption Authentication

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Basic

Advanced

Security

WDS

WPS

Administration

AP Client

Site Survey

Station List

Connect sc an

Site Survey

SSID BSSID RSSI Channel Encr yption Authentication

Quick Installation Guide

Mini Travel Router

Internet cable

OUTLET

Internet

cable

OUTLET

Cable network

interface

Articles to check: ●Wireless Pocket Router ●DC adapter

●RJ-45 cable ●USB cable ●Quick Installation Guide

WA02

WP02

WH01-G1

WP03

WH01-N1

WP02-N1

WA01

WH02

WA02

WP02

WH01-G1

WP03

WH01-N1

WP02-N1

WA01

WH02

Note:

1.In router and client modes, please set IP address and DNS address of your

computer as “Obtain DNS server addressautomatically”.

2.In client mode, please set the IP address of local wireline network, connect

with Wireless Pocket Router by wireline connection way, then login the

management interface.

3.In AP mode, if IP address can be assigned dynamically in wireline network,

please set IP address and DNS address of your computer as “Obtain an IP

address automatically” and “Obtain DNS server address automatically”, if it

adopts specified static IP, then please configure IP address and DNS address

by manual setting.

19 2.168 .16.12

25 5.255 .255.0

192.168.16.254

AP mode

User can switch to modes of AP, client and router by just switching the button by the side of Wireless Pocket Router, and please note that the mode exchange takes exactly one minute

1.Operating mode selection

Access Point---wired network

exchange to wireless network

Bridge---wireless network

exchange to wired network

Repeater---wireless hotspot

extension and amplification

Wireless access to WAN,

supports PPPoE, dynamic IP,

Static IP. Supports China mobile,

Unicom, China Telecom hotspots

identification access, wireless

hotsport sharing

Acts as Router, access to WAN

with wire, supports PPPoE,

dynamic IP and static IP

<Router mode>Introductions

is shown in the third section

of <Operation modes settings>

Router mode

AP mode <Wireless signal amplification/

relay settings> is shown in the

third section of <Operation

modes settings>

Operating

mode

Basic function(application) Hardware connection and

software setup

This wireless pocket router supports quick exchange among AP, Client

and router modes with switch on the side.

wireless AP settings> is

shown in the third section

of <Operation modes settings>

Wired router change to

<Client mode>Introductions

is shown in the third section

of <Operation modes settings>

Client mode

Connected

the wireless signal amplified, thus expanding the signal coverage.

Wireless receiver---GGSN

of wireless network exchange

to wired network

When work in router mode, its Ethernet port acts as WAN port, which connect

to ADSL Modem or broadband access to realize wireless network multimachine sharing,

Applicable environment:home-use or apartment application.

Mini Travel Router

LAN LI NE

POWER L AN WIFI

RT Clie nt AP

POWER LA N WIF I

RT Cli ent AP

Please select “STATIC (fixed) IP” connection type if your ISP offers a static IP

If you use ADSL PPPoe, please select "PPPoE(xDSL)"

If ISP assign IP dynamically, select the default connection type as"DHCP(Auto config)"

①Select “STATIC (fixed) IP”

② Input IP address, subnet mask, Default Gateway and

Primary DNS servers offered by ISP

③ If MAC Clone is required by ISP, please select“Enable”

and input valid MAC address

④ Click “Apply”, it will take effect after auto reboot of the AP

① Select " "DHCP(Auto config)

② Input the "Host Name" or just leave it without configuration

③ If MAC Clone is required by ISP, please select

"Enabled" and input valid MAC address. Default

is disabled

④ Click "Apply", it will take effect after auto reboot

of the Wireless Pocket Router

① Select "PPPoE (xDSL)"

② Input the user name and password offered by ISP

③ Select relevant operation mode according to the situation

④ If MAC Clone is required by ISP, please select“Enable” and

input valid MAC address

⑤ Click “Apply”, it will take effect after auto reboot of the AP

Please refer to the first page of "Configuration before application" to set up

network, then go to its management interface

Router(RT)mode

Wide Area Network settings

If the Base Station (BS) is encrypted, then please input the password.

If the connection is activated successfully, then an icon" "will

appear.

Some configuration of wireless access points in the "system

setting" is automatically generated without setting, you don't

need to modify the configuration and adjust adpot the default

setting.

Router/Client mode configuration

A.Spread "The wireless network settings", click "Site Survey"

B.find out the WISP or access point you need to connect

and select it, click"scan"if it is not on the list

C.Click "Add Profile"

2 3

Online-bound activation

When works in this mode, the wireless network acts as WAN, wireline

network acts as LAN, it can connect wireless hotspot and or router like wireless card, then

connect the PC or other network device with ethernet port by cable.

Mini Travel Router

POWER L AN WIFI

RT Clie nt AP

POWE R LA N WIF I

RT Client AP

Client mode

In Router/Client mode, please refer to wide Area Network configuration

in router mode, then configure as follows.

POWER

WIFI

WLAN

1.Under the condition of thunder or storm,

please unplug the connected power and

wire of device to avoid damage from thunder；

2.Keep away of moisture during storage,

transportation and operation；

3.Use the power adapter of the device；

4.Keep away from interference sources

(cordless telephone, microwave oven and

refrigerator etc)

Warning

Tips

Select WPA-PSK, WPA2-PSK or WPA-PSK/WPA2-PSK (recommended)

as the security mode

Select “OPENWEP” as the security mode

① Select a security mode

② Select the “WPA algorithms” here,

it is recommended to select “AES”

③ Input the pass phrase you set,

which shall be 8-63 ASCII

character,or 8-64 hex digits

④ Click “Apply”, it will take effect

after auto reboot of the Wireless

Pocket Router

The default of is without wireless security/encryption settings, for the sake of your network security, it is suggested to setup

wireless security/encryption to prevent unauthorized access.

Mini Travel Router

Wireless security settings

①

② Select the default key number here

③ Input the password you set in WEP Keys,

For Hex key number key number can be

set as a 10 or 26 hexadecimal character.

(Arabic numerals 0-9 or letter ABCDEF);

For ASCII key number; password can be

a 5 or 13 ASCII characters

④ Click “Apply”, it will take effect after auto

reboot of the Wireless Pocket Router

Select a security mode

!!Tips:

When select OPENWEP or WPA as the security mode, while“WPA algorithms”as the TKIP or TKIPAES, the maximum data transmisstion rate would decline as 54Mbps, therefore it is suggested to select WPA

safety mode with AES algorithms to encrypt the wireless.

FAQ (Frequently Asked Question)

Question1: Power light does not light

1.Check whether the power adapter(5V 500mA~2000mA) matches this product.

2.Please check the power connection.

Question2: Unable to access to web server of the device

1.Check whether the connection of computer and device is correct and make sure the corresponding

indicator is glintling normally

2.Please note that whether is in routing client mode, as in this mode user can only

apply the wireless network connection

3.Affirm that your web browser is the latest version and supports Java

4.Disconnect the power supply of the router, connect the power a moment later, and then reboot the router

5.If you have done all steps as above but still cannot login the router management interface, it is

recommended that you press the function key on panel for 5 seconds to reset it as default value.

Question3: Unable to successfully connect the upper-level network device in wireless

router or wireless client mode

1.Please make sure that your settings are correct, network is connected properly and your upper-level

network device works normally

2.Check whether both of your upper-level network device and Wireless Pocket Router use the same

network segment. If it is, please change them into different network segment.

Question4: Why does the notebook fail to gain the wireless signal

1.If it is built-inl wireless card, then check whether there is a wireless switch firstly, and check whether the

switch is turned on. (You should confirm with notebook manufacturers or check notebook specifications)

2.Dispose any possibilities of displacement or interference.

Question5: What should I do if I forget the password?

Answer: If you forget the user name and password, the only way to solve this problem is to reset the

router, press the reset button and keep it for over 5 seconds, then leave the button, the reset is done,

both default user name and password are "admin".

Mini Travel Router

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Firewall

Administration

WAN

LAN

DHCP clients

Advanced Routing

QoS

STATIC Mode

IP Address:

Subnet Mask:

Default Gateway:

Primary DNS Ser ver:

Secondar y DNS Server:

MAC Clone

Select

MAC Address

0. 0. 0. 0

STATIC（fixed IP）

Enabled

Apply Cancel/Refresh

WAN Connection Type:

0. 0. 0. 0

0.0.0.0

0. 0. 0. 0

Fill my MAC

Save

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Firewall

Administration

WAN

LAN

DHCP clients

Advanced Routing

QoS

PPPoE Mode

User Name:

Password:

Verify Password:

Operation Mode:

MAC Clone

Select

pppoe_user

●● ● ● ● ● ● ● ● ●

PPPoE（xDSL）

Disable

Apply Cancel/Refresh

WAN Connection Type:

Save

Keep Alive

Keep Al ive:Redial Per iod seconds.

On dema nd Mode:Idle Time mi nute s.

Conne ct Disconne ct

●● ● ● ● ● ● ● ● ●

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Firewall

Administration

WAN

LAN

DHCP clients

Advanced Routing

QoS

DHCP Mode

Hostname(Optional):

DHCP（Auto confi g）

Apply Cancel/Refresh

WAN Connection Type:

Save

MAC Clone

Select

MAC Address

Enabl ed

Fill my MAC

Wide Area Network (WAN) Settings

Choose your connection type and their parameters here.

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Basic

Advanced

Security

WPS

WDS

Firewall

Administration

Select SSID

SSID choice

Access Po licy

Policy:

Wire Equivalence Protection（WEP）

WEP Keys

MP01

Disa ble

"MP 01"

Security Mo de OP ENW EP

Add a station Mac:

Station List

Default key Key 1

WEP Key 1

WEP 2Key

WEP 3K ey

WEP 4K ey

Hex

Apply Cancel/Refresh

Save

WiFi-150M Router

Wizard

Internet Settings

Wireless Settings

Basic

Advanced

Security

WPS

WDS

Firewall

Administration

Select SSID

SSID choice

Access Policy

Policy:

WPA

WPA Algorithms

Pass Phrase

TKIP AES

WP01

Disable

12345 678

"MP 01"

Security Mode WPA-P SK

Key Renewal Interval

Add a station M ac:

Station List

TKIPAES

seconds

3600

Apply Cancel/Refresh

Save

Site Survey

SSID BSSID RSSI Chan nel E ncr y pti on Authenticatio n Net work Type

Conn ec t sc an Add Pr of il e

Profile

Link Status

Site Sur vey

Advanced

11n Settings

WPS

Internet Settings

Wireless Settings

Wizard

Firewall

Administr ation

Profile L ist

SSID B SSID Chan nel Enc r yption Aut henti catio n Netwo rk Type

Profil e

Link Sta tus

Site S urve y

Advanced

11n Settings

WPS

Inter net Settings

Wireless Settings

Wizard

Firewall

Administrat ion

Add Del et e E di t Activate

Profile List

SSID B SSID Chan nel Encr ypt ion Authen ticat ion Networ k Type

Profile

Link Status

Site S urvey

Advanced

11n Settings

WPS

Inter net S ett ing s

Wirel ess S ettings

Wizard

Firew all

Administration

Add Del ete Edi t Ac ti vate

System Configuration

Profile Name

SSID

Network Type

Power Saving Mode

RTS Threshold

Fragment Threshold

Security Policy

Security Mode

WPA

WPA Algorithms

Pass Phrase

CMA ）（Constantly Awake Mode

Power Saving Mode

Used

TKIP AES

PROF001

WA02

Infrastructure

2347

WPA-Personal

2346

Apply Cancel

● ● ● ● ● ●●●

Wireless indicator Indicator light glints slowly indicates no sig al transmitted

Indicator light glints quickly indicates signal transmitted

*If the indicator is not in normal state, please check the connection.

Once the connection is set up, please check the state of indicator light.

Indicator light Name of indicator Normal state

Indicator of power Light consistently

Indicator of LAN

system state Indicator light glints or keeps

lighting consistently with cable connection.

Internet cable

OUTLET

Internet cable

Telephone

line

OUTLET

WA0 2

WP02

WH01-G1

WP03

WH01-N1

WP02-N 1

WA0 1

WH02

WA0 2

Router mode

Client mode

Client

Router

Tabla de contenidos

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad