Precor 9.33 Manual de usuario

9.33, 9.35 240V Treadmill

Page 1

9.33, 9.35 Treadmill

Warning: This service manual is for use by Precor trained service providers only.

IfyouarenotaPrecorTrainedServicer,youmustnotattempttoserviceanyPrecorProduct;

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and

replacement procedures required to repair and maintain this product.

This document contains general product information, software diagnostic procedures (when

available), preventative maintenance procedures, inspection and adjustment procedures,

troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the

left of this page. You may “drag” the separator bar between this page and the bookmark section

to change the size of the page being viewed.

Unauthorized Reproduction and Distribution Prohibited By Law

20081-119

9.33, 9.35 240V Treadmill

Page 2

Section One -

Things you Should Know

The 9.33, 9.35 incorporate new drive motor system and display systems. The drive motor is a

three phase AC motor. The drive motor controller converts a single phase AC input into three

phase motor control.

Section One, Things You Should Know. This section includes technical specifications. Read

this section, as well as the 9.33, 9.35 Treadmill Owners Manual, before you perform the

maintenance procedures in this manual.

Section Two, Software Features. Precor’s 9.33, 9.35 Treadmills are programmed with several

diagnostic and setup features. This section contains the procedures you need to access the

diagnostic features on this treadmill.

Section Three, Checking Treadmill Operation. This section provides you with a quick way of

checking treadmill operation. Check treadmill operation at the end of a maintenance procedure

and when it is necessary to ensure that the treadmill is operating properly.

Section Four, Inspection and Adjustment Procedures. Perform inspection procedures when

a trouble symptom points to a particular problem and after removing and replacing major

components. Many maintenance problems can be fixed by adjusting various treadmill

components. This section also provides you with the step-by-step procedures required to make

these adjustments.

Section Five, Troubleshooting Procedures. The diagnostic and troubleshooting procedures

contained in this section should be performed when it is necessary to isolate a problem to a

particular component.

Section Six, Replacement Procedures. When a treadmill component must be replaced, go to

this section and follow the step-by-step procedures required to remove and replace the

component.

Section Seven, Technical Diagrams and Parts Lists. This section includes wiring diagrams,

and block diagrams for the 9.33, 9.35 Treadmills.

9.33, 9.35 240V Treadmill

Page 3

Safety guidelines you should know and follow include:

• Read the owner’s manual and follow all operating instructions.

• Operate the treadmill on a solid, level surface.Visually check the treadmill before beginning

service or maintenance operations. If it is not completely assembled or is damaged in any

way, exercise extreme caution while operating and checking the treadmill.

• When operating the treadmill, do not wear loose clothing. Do not wear shoes with heels or

leather soles. Check the soles of your shoes and remove any embedded stones. Tie long

hair back.

• Do not rock the unit. Do not stand or climb on the handlebars, display enclosure, or cover.

• Do not set anything on the handlebars, display enclosure, or cover. Never place liquids on

any part of the treadmill, while performing service.

• To prevent electrical shock, keep all electrical components away from water and other

liquids.

• Do not use accessory attachments that are not recommended by the manufacturer-such

attachments might cause injuries.

• Removing the hood exposes high voltage components and potentially dangerous

machinery. Exercise extreme caution when you perform maintenance procedures with the

hood removed.

9.33, 9.35 240V Treadmill

Page 4

General Information

For the latest exploded view diagram, part number and part pricing information, visit the Precor

dealer website at “www.precor.com/connection.

9.33, 9.35 240V Treadmill

Page 5

Procedure 2.1 - Accessing the Hardware Validation Program

The treadmill's diagnostic program consists of the following modes:

• Display Test

• Keyboard Test

• Heart Rate Test

• Machine Test

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 below and press keys RESET,5,1,7,6,5,7,6,1, sequentially. Use the

numeric keypad to enter the number sequence. The ARROW keys will step you through the

test modes listed above, allowing you to skip tests or perform only specific tests.

3. DISPLAY TEST.

4. Press the OK key to enter the display test. Press the OK or ENTER key several times to

step through all of the LED’s on the display. Ensure that all of the LED’s illuminate. Press

and hold the OK or ENTER key to exit the display test.

Diagram 2.1 - 9.33 Display

Numeric

Keypad

OK key

Arrow Keys

RESET key

9.33, 9.35 240V Treadmill

Page 6

5. KEYBOARD TEST.

6. The keyboard test will place a dot on the display for each key on the display, including the

numeric keypad. Pressing a key will cause the dot associated with the key to go out. Test all

of the keys in this manner. Tug on the safety key lanyard, to ensure that the STOP key is

activated.

7. Press and hold the OK or ENTER key to exit the keyboard test.

8. HEART RATE TEST.

9. The heart rate test will display the heart rate being received during this test from the hand

held grips, chest strap transmitter or test transmitter.

10. The display will toggle between unfiltered and filtered heart rate readings. They will be

prefixed “U” for unfiltered, “F” for filtered. When a heart rate signal is being accepted the

“heart” will blink and the heart rate will be displayed in the heart rate window and the main

window. Test the heart rate in both the hand held and wireless (chest strap or test

transmitter) modes.

11. Press the OK or ENTER key to exit the heart rate test.

12. MACHINE TEST.

13. There are two test modes in the MACHINE TEST, they are BELT SPEED and INCLINE.

Use the ARROW keys to select the desired test.

14. BELT SPEED

15. Press the OK or ENTER key. POWERBITS will be momentarily displayed then the powerbit

number will be displayed. The power bit level can be checked by starting the running belt.

16. Press the OK key to exit the belt speed test.

17. INCLINE

18. Press the OK or ENTER key. A/D will be momentarily displayed then the analog to digital lift

position number will be displayed. The analog to digital lift position number represents the

incline’s physical position. The A/D number is used to calibrate the incline. The incline must

be calibrated when a new lift motor is installed.

Press the RESET to exit the MACHINE TEST.

9.33, 9.35 240V Treadmill

Page 7

Procedure 2.2

- Accessing the Information Display Program

The information display will access the following data;

• Odometer

• U Boot SW

• U Base SW

• Lower SW

• Usage log

• Error log

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 above and press keys RESET,6,5 sequentially. Use the numeric

keypad to enter the number sequence. The ARROW keys will step you through the display

modes listed above, allowing you to skip displays or view only specific displays.

3. The display will momentarily read, DIAGS - INFORMATION DISPLAY.

4. ODOMETER

5. Press the OK or ENTER key. The treadmill’s odometer will be displayed as 1234567 MILES

or 1234567 KM.

Note: The odometer data is stored in non-volatile memory on the upper PCA. If the upper PCA

is replaced the odometer data will be lost.

6. Press the OK or ENTER key to exit the odometer display.

7. HOUR METER.

8. Press the OK or ENTER key. The operating time of the unit will be displayed as 12345

HOURS. The operating time is defined as total amount of time that the unit has operated in

program modes with the drive motor running. The hour meter is also used to provide the

“time stamp” for the error code log.

9. Press the OK or ENTER key to exit the hour meter display.

10. U BOOT SW

11. Press the OK or ENTER key. The U Boot SW part number will be displayed. The U Boot SW

is the software internally used to upload upper PCA operating system software (U Base

SW).

12. Press the OK or ENTER key to exit the U Boot SW display

9.33, 9.35 240V Treadmill

Page 8

13. U BASE SW

14. Press the OK or ENTER key. The U Base SW part number will be displayed. The U Base

SW is the upper PCA operating system software.

15. Press the OK or ENTER key to exit the U Base SW display.

16. LOWER SW

17. Press the OK or ENTER key. The Lower SW part number will be displayed. The Lower SW

is the lower PCA operating system software.

18. Press the OK or ENTER key to exit the Lower SW display.

19. SERIAL NUMBER

20. Press the OK or ENTER key. The treadmill’s serial number will be displayed.

21. Press the OK or ENTER key to exit the serial number display.

22. USAGE LOG

23. Press the OK or ENTER key. The usage for each program can be displayed. The ARROW

keys will allow to scroll through the list of programs. For example the manual program usage

will be displayed as MANUAL USED X TIMES TOTAL X MINUTES.

24. Press the OK or ENTER key to exit the usage log display.

25. ERROR LOG

26. Press the OK or ENTER key.

27. The error log will store up to 10 error conditions. The errors are logged with the most recent

error in position one. When a new error condition occurs, each existing error is pushed down

one position in log. If there was an error in position 10 when a new error was logged, the

error that was in position 10 will be lost.

28. Each error in the log will show the odometer reading (in miles) and the time (hour meter) and

motorcurrentreadingwhentheerroroccurred.Theerrorsaredisplayedas;

1 ER20 XXXXX MI XXX HRS. XX.X AMPS

29. The ARROW keys will allow you to scroll through the log.

30. When the QUICK START key is held for 2 seconds the message HOLD TO CLEAR

ERRORS will be displayed. If the QUICK START key is held for an additional 2 seconds, the

log will be cleared. The message NO RRORS will be displayed and all error are erased from

the log.

9.33, 9.35 240V Treadmill

Page 9

Procedure 2.3 - Setting Club Parameters

This procedure allows you to change the following settings:

• Safety Code

• Select Units

• Set Max Pause Time

• Set Cool Down Time

• Set Speed Limit

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 above and press keys RESET,5,6,7,1 sequentially. Use the numeric

keypad to enter the number sequence. The ARROW keys will step you through the display

modes listed above, allowing you to skip displays or view only specific displays.

3. The display will momentarily display DIAGS - SET PARAMETERS

4. SAFETY CODE

5. Press the OK or ENTER key. When enabled the safety code will require the user to enter a

“password” before the trammel can be used.

6. Use the ARROW keys to select either ENABLED or DISABLED.

7. Press the OK or ENTER key to exit the safety code display

8. SELECT UNITS

9. The currently selected measurement unit will then be displayed.

10. Use the ARROW keys to toggle between U.S. and METRIC.

11. Press the ENTER key to select the currently displayed measurement unit.

12. SET MAX PAUSE TIME

13. Press the OK or ENTER key.

14. Use the ARROW keys to set the maximum pause time between 1 and 10 minutes.

15. Press the ENTER key to select the currently displayed pause time.

16. SET COOL DOWN TIME

9.33, 9.35 240V Treadmill

Page 10

17. Press the OK or ENTER key.

18. Use the ARROW keys to set the COOL SOWN time between 1 and 5 minutes.

19. Press the ENTER key to select the currently cool down time.

20. SET SPEED LIMIT

21. Press the OK or ENTER key.

22. Use the ARROW keys to set the maximum speed between 1 and 12 MPH.

23. Press the ENTER key to select the currently displayed speed limit.

24. Press the RESET key to exit the set club parameters display.

Otros manuales para 9.33

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rueda de andar de Precor

Precor

Precor C954i Instrucciones de instalación y funcionamiento

Precor

Precor GEN06 Series Manual de usuario

Precor

Precor Experience 800 Manual de usuario

Precor

Precor 9.33 Manual del propietario

Precor

Precor C954i Manual de usuario

Precor

Precor 9.31 Manual del propietario

Precor

Precor C954i Manual de usuario

Precor

Precor TRM 800 Instrucciones de montaje

Precor

Precor Experience 700 line Series Manual de usuario

Precor

Precor C932 Manual de usuario

Precor

Precor M9.33i Manual de usuario

Precor

Precor TRM 800 Instrucciones de montaje

Precor

Precor PRECISION SERIES Manual técnico

Precor

Precor Experience Series 700 Line Manual de usuario

Precor

Precor TRM10/GEN06 Manual de usuario

Precor

Precor 9.23 Manual de usuario

Precor

Precor 9.23 Manual de usuario

Precor

Precor M9.20 Manual de usuario

Precor

Precor C960 Manual de usuario

Precor

Precor M9.25i Manual de usuario

Precor

Precor Experience Series 700 Line Manual de usuario

Precor

Precor M9.41si Manual de usuario

Precor

Precor c944 Manual de usuario

Precor

Precor Electronic M9.4 Manual de usuario

Manuales populares de Rueda de andar de otras marcas

Treadly

Treadly TREADLY 2 Manual de usuario

HEALTH ONE

HEALTH ONE Walk Ro Manual de usuario

NordicTrack

NordicTrack NTL12941 Manual de usuario

NordicTrack

NordicTrack T7.5 S Manual de usuario

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Manual de usuario

Merax

Merax MS282992 Manual de usuario

FYTTER

FYTTER RU-2SX Manual de usuario

FitLogic

FitLogic freewill d225 Manual de usuario

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Manual de usuario

Horizon Fitness

Horizon Fitness Adventure 5 Plus Manual de usuario

Stamia

Stamia InMotion II Manual de usuario

Smooth Fitness

Smooth Fitness EVO 3i Manual de usuario

NordicTrack

NordicTrack NETL81810.0 Manual de usuario

Schwinn

Schwinn 830/Journey 8.0 Manual de usuario

Keys Fitness

Keys Fitness HealthTrainer HT-740T Manual de usuario

Spirit

Spirit XT8 Manual de usuario

NordicTrack

NordicTrack T 14.0 Treadmill Manual de usuario

Master

Master F22 Manual de usuario