Precor 9.21 Manual de usuario

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 1

9.21, 9.21i, 9.21s, 9.21si Treadmill

Warning: This service manual is for use by Precor trained service providers only.

IfyouarenotaPrecorTrainedServicer,youmustnotattempttoserviceanyPrecorProduct;

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and

replacement procedures required to repair and maintain this product.

This document contains general product information, software diagnostic procedures (when

available), preventative maintenance procedures, inspection and adjustment procedures,

troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the

left of this page. You may “drag” the separator bar between this page and the bookmark section

to change the size of the page being viewed.

Unauthorized Reproduction and Distribution Prohibited By Law

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 2

Section One - Things You Should Know

About This Appendix

Section One, Things You Should Know. This section includes technical specifications and a

procedure matrix. Read this section, as well as the 9.21, 9.21i, 9.21S, 9.21Si Treadmill Owner’s

Manual, before you perform the maintenance procedures in this manual.

Section Two, Software Features. Precor’s 9.21, 9.21i, 9.21S, 9.21Si Treadmill is programmed

with several diagnostic and setup features. This section contains the procedures you need to

access the diagnostic features on this treadmill.

Section Three, Checking Treadmill Operation. This section provides you with a quick way of

checking treadmill operation. Check treadmill operation at the end of a maintenance procedure

and when it is necessary to ensure that the treadmill is operating properly.

Section Four, Inspection and Adjustment Procedures. Perform inspection procedures when

a trouble symptom points to a particular problem and after removing and replacing major

components. Many maintenance problems can be fixed by adjusting various treadmill

components. This section also provides you with the step-by-step procedures required to make

these adjustments.

Section Five, Troubleshooting Procedures. The diagnostic and troubleshooting procedures

contained in this section should be performed when it is necessary to isolate a problem to a

particular component.

Section Six, Replacement Procedures. When a treadmill component must be replaced, go to

this section and follow the step-by-step procedures required to remove and replace the

component.

Section Seven,Wiring and Block Diagrams. This section includes wiring and block diagrams

for 9.21, 9.21i, 9.21S, 9.21Si Treadmill.

General Information

For the latest exploded view, part number and part pricing information, visit the Precor dealer

website at “www.precor.com/Dealer”.

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 3

Technical Specifications

PHYSICAL SPECIFICATIONS

Length: 67 inches (170 cm)

Width: Handrails 28.5 inches (71 cm)

Base 25 inches (63.5)

Height: 44 inches (117 cm)

Running surface: 51 inches by 17 inches (129.5 cm by 43 cm)

Motor: 1.7 hp continuous duty (9.21 & 9.21S)

2.0 hp continuous duty (9.21i & 9.21Si)

Speed: 0.5 to 10 mph (0.8 to 16 kph)

10 mph is equivalent to a 6 minute mile

Incline: 0 to 15% grade

Power: 50/60Hz 120v AC 20 Amps

Weight: 193 lbs (87 kg)

Shipping weight: 233 lbs (105 kg)

ELECTRONIC SPECIFICATIONS

9.21 & 9.21i Programs:

Manual

Interval (1 minute rest: 1 minute work)

Weight Loss

9.21S & 9.21Si Programs:

Heart Rate Interactive Course

Manual

Interval (1 minute rest: 1 minute work)

Weight Loss

6 Preprogrammed courses (3 Walk, 3 Run)

2 Custom courses

9.21, 9.21i, 9.21S & 9.21Si Display Readouts:

Distance (miles or kilometers)

Time

Speed (mph or kph)

Calories

Incline

Heart rate

Scan

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 4

Procedure 2.1 - Accessing the Diagnostic Program

(prior to July 21, 1997)

The 9.21, 9.21S diagnostic program cycles through the following modes:

Software Version Mode. Displays the PROM version number.

LED Mode. Illuminates each of the LED’s mounted on the upper PCA.

Lift Mode. Allows you to verify that the lift calibration number increments and decrements as the

INCLINE keys are pressed.

Power Bits Mode. Allows you to verify that the power bits number increments and decrements

as the SPEED keys are pressed.

Note:

When the treadmill is in power bits mode and the SPEED ▲key is selected, the treadmill speed

will increase twice as fast as it does when the treadmill is in a normal operating mode.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

Note:

Diagram 2.1 illustrates the 9.21 Treadmill display. The 9.21S Treadmill display is shown in

Diagram 2.2.

2. Press and hold the STOP, SPEED ▼, SPEED ▲and QUICK START keys simultaneously.

3. The electronic console displays the version number of the PROM mounted on the upper

PCA. Record the PROM version number.

4. Following the version number, a horizontal line sweeps from top to bottom and then a

vertical line sweeps from right to left.

Note:

The lines check the LED’s mounted on the upper PCA. If the lines are broken when they sweep

across the electronic console, replace the upper PCA as described in Procedure 5.2 of the

Residential Treadmill Service Manual.

5. After the LED test, the electronic console displays the potentiometer increment number.

6. Press the INCLINE keys. Verify that the running bed inclines and declines as the INCLINE

keys are pressed.

7. Watch the electronic console. When the potentiometer increment number is displayed on

the electronic console, enter power bit mode by starting the running belt.

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 5

Note:

When the running belt is started, the number of power bits will be displayed. Power bits are

directly related to the drive motor input signal.

8. Press the SPEED ▲ and ▼keys. Verify that the power bits number increments and

decrements as the SPEED keys are pressed.

9. Press STOP to return to the Enter Your Weight banner.

10. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall outlet.

Diagram 2.1 - 9.21 Display

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 6

Diagram 2.2 - 9.21S Display

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 7

Procedure 2.2 - Accessing the Diagnostic Program (after

July 20, 1997)

Units built after July 20, 1997 used the standard access codes. The keys on the display are

hypothetically numbered for 1 to 7 from left to right. Therefore, ENTER would be key 1, INCLINE

▼ would be key 2, etc. (see Diagram 2.1or 2.2) or on a 9.21i or 9.21Si INCLINE ▲ would be key

1, INCLINE ▼ would be key 2, etc. (see Diagram 2.3).

Placing the unit in the diagnostic mode causes the software to perform the following operations:

a. Test the LED’s mounted on the upper PCA;

b. Provide the option of calibrating the lift system;

c. Display the drive motor power bits;

d. Display and test the heart rate function;

e. Display the error code log;

f. Provide a method of checking the operation of the keys on the electronic console;

g. Test the circuit breaker trip function.

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Press keys RESET,5,1,7,6,5,7,6,1, sequentially.

3. Following the version number, a horizontal line sweeps from top to bottom and then a

vertical line sweeps from right to left.

Note:

The lines check the LEDs mounted on the upper PCA. If the lines are broken when they sweep

across the electronic console, replace the upper PCA.

4. After the LED test, the electronic console displays the potentiometer increment number.

5. Press the INCLINE keys. Verify that the running bed inclines and declines as the INCLINE

and DECLINE keys are pressed.

6. Watch the electronic console. When the potentiometer increment number is displayed on

the electronic console, enter power bit mode by starting the running belt.

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 8

Note:

When the running belt is started, the number of power bits will be displayed. Power bits represent

the amount of power applied to the drive motor. Power bits are the product of selected speed and

applied load.

7. Press the SPEED ▲ and ▼keys. Verify that the power bits number increments and

decrements as the SPEED keys are pressed.

8. Press the STOP key to exit the power bits mode and enter the heart rate mode.

9. If the heart rate option has been installed, you may test the heart rate function using a chest

strap transmitter or test transmitter.

10. Press the ENTER key to enter the error code log. The error code log will display the last 10

errors that occurred. Error 1 will be the most recent error and error 10 will be the oldest

error. If more than 10 errors occur, the most recent error will be inserted in position 1 and all

other errors will be pushed down one position. The error that was in the 10th position will be

lost. If you wish to clear the error code log, press the QUICK START and STOP keys,

simutaneously.

11. Press the ENTER key to exit the error code log and enter the key pad test.

12. Press each key one at a time the display will confirm the key that was pressed. Press the

INCLINE▼and SPEED ▲ keys, simultaneously to exit the keypad test.

13. The next test is the circuit breaker test. Follow the instructions on the display to cause either

a test trip of the treadmill circuit breaker or exit the diagnostics program.

Diagram 2.3 - 9.21i and 9.21Si Display

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 9

Procedure 2.3 - Displaying the Odometer

(prior to July 21, 1997)

This procedure allows you to display the number of miles or kilometers logged on the treadmill.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. With the Enter Your Weight banner scrolling, press the STOP key, the SPEED ▼key, and

then the SPEED ▲key sequentially

Note:

After you perform Step 2, the electronic console displays the number of miles or kilometers

logged on the treadmill.

3. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall outlet.

9.21, 9.21i, 9.21S, 9.21Si Treadmill

Page 10

Procedure 2.4 - Displaying the Odometer

(after July 20, 1997)

The diagnostic program used prior to July 21, 1997 and the diagnostic program used after July

20, 1997 are essentially the same except that the key strokes used to access the programs are

different. Units built after July 20, 1997 used the standard access codes. The keys on the display

are hypothetically numbered for 1 to 7 from left to right. Therefore, ENTER would be key 1,

INCLINE ▼ would be key 2, etc. (see Diagram 2.1) or on a 9.41Si INCLINE ▲ would be key 1,

INCLINE ▼ would be key 2, etc. (see Diagram 2.2).

This procedure allows you to display the number of miles or kilometers logged on the treadmill.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker

2. Press keys RESET,6,5, sequentially.

3. The software version will be displayed. Press the ENTER key to continue.

4. The console displays the number of miles logged or kilometers on the treadmill.

5. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall outlet.

Otros manuales para 9.21

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rueda de andar de Precor

Precor

Precor 9.35 Manual del propietario

Precor

Precor 905e Manual de usuario

Precor

Precor C954 Manual de instrucciones

Precor

Precor C934 Manual de usuario

Precor

Precor 9.23 Manual de usuario

Precor

Precor Treadmills 932i Manual del propietario

Precor

Precor Electronic M9.4 Manual de usuario

Precor

Precor C966 Manual de instrucciones

Precor

Precor 9.41s Manual de usuario

Precor

Precor M9.41si Manual de usuario

Precor

Precor TRM 800 Instrucciones de montaje

Precor

Precor C932i Manual de usuario

Precor

Precor 9.31 Manual de usuario

Precor

Precor C954 Manual de usuario

Precor

Precor 9.45 Manual de usuario

Precor

Precor C966i Manual de usuario

Precor

Precor Cycles Integrated LCD Screen Option none Manual de usuario

Precor

Precor LOW-IMPACT TREADMILLS 9.33 Manual de usuario

Precor

Precor Experience 600 Series Manual de usuario

Precor

Precor 9.31 Manual de usuario

Precor

Precor 9.31 Manual de usuario

Precor

Precor 9.33 Manual del propietario

Precor

Precor Experience Series 700 Line Manual de usuario

Precor

Precor c944 Manual de usuario

Manuales populares de Rueda de andar de otras marcas

Treadly

Treadly TREADLY 2 Manual de usuario

HEALTH ONE

HEALTH ONE Walk Ro Manual de usuario

NordicTrack

NordicTrack NTL12941 Manual de usuario

NordicTrack

NordicTrack T7.5 S Manual de usuario

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Manual de usuario

Merax

Merax MS282992 Manual de usuario

FYTTER

FYTTER RU-2SX Manual de usuario

FitLogic

FitLogic freewill d225 Manual de usuario

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Manual de usuario

Horizon Fitness

Horizon Fitness Adventure 5 Plus Manual de usuario

Stamia

Stamia InMotion II Manual de usuario

Smooth Fitness

Smooth Fitness EVO 3i Manual de usuario

NordicTrack

NordicTrack NETL81810.0 Manual de usuario

Schwinn

Schwinn 830/Journey 8.0 Manual de usuario

Keys Fitness

Keys Fitness HealthTrainer HT-740T Manual de usuario

Spirit

Spirit XT8 Manual de usuario

NordicTrack

NordicTrack T 14.0 Treadmill Manual de usuario

Master

Master F22 Manual de usuario