PRECISION DIGITAL PD213 Manual de usuario
I&M008-10136-07/2011 (dwg. 83B234-01 Rev. C 3/06)
Industrial Digital
Pressure Gauge
Model PD213, PD214, PD224
Operating
Instructions
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 1
– 2–
Congratulations on your purchase of the
Precision Digital Industrial Gauge. This feature-
packed gauge offers a menu-driven display for
easy customization. User selectable features
include 12 units of measurement, password
protected calibration and disable functions,
adjustable bargraph and update rate.
A five digit display for maximum resolution is
standard. Optional 4-20mA output, relays and
24Vdc power add to the versatility of the gauge.
With the range printed on the keypad. These
digital gauges meet ASME B40.7 specification.
See a complete listing of product features and
specifications on pages 16.
89 October Hill Rd, Suite 5,
Holliston, MA 01746.
Tel: 800-343-1001
Fax: 508-655-8990
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 2
– 3–
TAB E OF CONTENTS
Quick Reference ............................................4-5
Keypad Functions ..........................................6-8
• ON/O KEY
• ZERO/CLEAR KEY
• MIN/MAX KEY (down arrow key)
• MENU KEY
• BACKLITE KEY (up arrow key)
• ENTER KEY
MENU Functions (MENU Mode) ................................8-15
• Engineering Units
• CON IG Mode
• Set Password
• Recalibration of Gauge
• Zero Key Adjustment
• Disabling Menu Options
• Bargraph Options
• Auto Off Options
• Update Options for Displayed Pressure
• Dampening Options
• Backlight Options (Backlight Optional)
• Set Switch (Relay) Options
Specifications ................................................16
Ranges ........................................................16
Display Messages ..........................................17
Wiring Diagrams ........................................18-21
Gauge Installation & Maintenance........................24
• Mounting
• Battery Replacement & Installation
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 3
– 4–
Bargraph
% of full scale
Flashing display when unit
pressured below zero
Press to indicate minimum
or maximum pressure
gauge has measured
Press again to return to
pressure units
Press to read menu
U ITS (Pressure)
E GLISH
I HG
PSI*
I H2O
@ 4°C, 20°C, 60°F
FTW
FTSW
METRIC
BAR
MBAR
KPA
CMH2O
KG/CM2
UPDATE RATE
(Pressure measurement
per second)
10x (100 MS)*
5x (200 MS)
2x (500 MS)
1x (1 Sec)
BACKLITE
(Off options)
ever
2 SEC
5 SEC*
15 MI
30 MI
.88˝ high digital display (41⁄2˝ case)
.60 high digital display(3˝ case)
QUICK REFE
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 4
– 5–
While in unit of measurement mode (eg: psi),
press the ZERO CLEAR button to rezero the
gauge. This feature functions when displayed
pressure is within ±5% or 10% of zero value
This Bargraph indicates battery level;
the more segments, the closer the
battery is to full charge (only dis-
played on units with battery
Flashing display when unit
pressurized beyond full-scale
Press to turn backlight on or off
(backligh optional)
Range on keypad;
complies with ASME B40.7
Press to turn unit on or off
ent
AUTO OFF
(Turns unit off after
option selected)
Ne er*
2 minutes
5 minutes
15 minutes
30 minutes
CALIBRATE
Zero and span
adjustments,
password
protected
DISABLE
Allows for
“lockout” of
ME U
options
DAMPE I G
(Takes pressure reading
and averages
process pressure
None*
Avg 2
Avg 4
Avg 6
Avg 8
*Indicates Default
REFERENCE
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 5
– 6–
Turns the gauge on and off. When pressing the
ON/O key while in the off position, gauge start-
up display first indicates the software version
followed by the gauge pressure range. The
gauge will then display indicated pressure and be
ready for use.
Press this key for one second prior to gauge
usage to rezero any initial zero shift. If zero shift
is greater than programmed zero allowance, the
gauge will display O SET (blinking) for 1 sec-
ond, then return to the measure mode. To clear
minimum and maximum values, press
ZERO/CLR button (when min/max values are
indicated). Gauge will auto advance once zeroed.
KEYPAD FUNCTIONS
ON/OFF
ZERO
C R
MAX/MIN The Max/Min key allows review of minimum and
maximum pressure values since unit start-up or
last push of the clear key. Press key to:
1) Indicate maximum pressure.
2) Indicate minimum pressure.
3) Exit MAX/MIN mode and return the unit to
pressure measurement mode. To clear mini-
mum and maximum values press ZERO/CLR
key (must be in MAX/MIN mode).
The (down arrow key) is used in the MENU
mode, see following MENU key section.
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 6
– 7–
This key allows for customization of the gauge.
Pressing the MENU key allows cycling through
the main MENU items; UNITS, CON IG, GRAPH,
O , UPDAT & DAMP. Any item changed in the
Menu become the new default setting(s).
Revised settings are saved in the event of power
loss.
The (up arrow key) or (down arrow key)
on the keypad allows for scrolling through the
MENU options to increase or decrease numeric
values as required. If in the menu mode, gauge
will automatically advance to measure mode
once selected MENU item has been set.
This key manually turns the backlite on or off.
five options are available. They include NEVER,
10 sec, 30, sec, 1 min, 5 min*. With the NEVER
option, the gauge BACKLITE will remain lit
whenever the gauge is in the ON mode or until
the BACKLITE button is pushed again. Options,
10 sec, 30 sec, 1 min, 5 min*. allow the BACK-
LITE to automatically turn-off after a selected
period of time.
To use the BACK ITE option:
Step 1: Press the MENU key.
Step 2: Press the (up arrow key) or (down
arrow key) until the word LITE appears.
Step 3: Press ENTER.
Step 4: Press the (up arrow key) or (down
arrow key) to select the BACKLITE option.
Step 5: Press the ENTER key to finalize your
choice of LITE options.
KEYPAD FUNCTIONS
MENU
Key for gauge
with Backlite
Key for gauge
without Backlite
displayed with
(up arrow
icon only)
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 7
– 8–
KEYPAD FUNCTIONS
MENU OPTIONS
UNITS: 12 units of measurement are available: psi, mmHG,
inH2O with three temperature options: 20°C, 60° , 4°C*,
mBar, inHg, ftH2O, mPa, kPa, kg/cm2and bar.
Step 1: Press the MENU key until the word UNITS appears.
Step 2: Press Enter.
Step 3: Press the (up arrow key) or (down arrow
key) to select the required unit of measure.
Step 4: Press ENTER to finalize the UNIT selection.
ote: For inH20 range with three temperature options,
press the
(up arrow key) and
(down arrow key) to
select the desired temperature, then press E TER to final-
ize the U IT selection.
CONFIG: This option allows access to additional Menu
options. Options include:
• ENTPW or enter password (this appears as a sub-menu
in the CO FIG mode if a user password has been set).
• RECA (allows for zero, span and mid-scale calibra-
tion of the gauge).
• 0bUTN or zero key (allows for adjustment of % of
range that can be zeroed),
• dISAb, allows for disabling MENU options.
• SETPW: This feature allows for a user defined numer-
ic password. If a user password is not set, all features
in the CON IG mode will be accessible without a
password. If a user password is set, all items in the
CON IG menu options are accessible with or without
a user password. If a user password is programmed,
it will be required to access the CON IG menu options.
*Indicates default.
ENTER
This key allows for selecting gauge features in the
menu finalizing selection. Use of the enter key is
described throughout operating instructions.
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 8
– 9–
MENU FUNCTIONS
How to Use Your Menu Functions
To set a user password (SETPW):
Step 1: Press the Menu key on the keypad
Step 2: Press the (up arrow key) or (down arrow
key) until the word CON IG appears.
Step 3: Press Enter. The word SETPW appears on the
gauge display
Step 4: Press Enter. A five digit numeric password is now
required.
Step 5: Press the (up arrow key) or (down arrow
key) on the keypad to select the first digit of the password.
Step 6: Press ENTER.
Step 7: Repeat until the five-digit password is shown on
the gauge display.
Step 8: Press ENTER.
ote: to erase password at any time while in the SETPW
(set password) mode, press the ZERO/CLEAR key. The
user will be prompted to reprogram the password once the
five-digit password is entered. The gauge will display SAVE.
Step 9: Press Enter to save the password setting.
ENTPW: Once a user password has been established and
entry into the CON IG mode is required, the user will be
prompted to ENTPW or enter password.
Follow setup steps 4-8 above.
RECA : or recalibrate allows for zero, mid-scale, full-scale
and factory default calibration of the gauge. The RECAL
feature also allows for recalibration of gauges with
4-20mA output.
*Indicates default.
KEYPAD FUNCTIONS
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 9
– 10 –
To use RECA option:
Step 1: Press the Menu key on the keypad
Step 2: Press the (up arrow key) or (down arrow
key) on the keypad until the word CON IG appears.
Step 3: Press Enter.
Step 4: Enter user password if it has been programmed.
Step 5: Press (up arrow key) or (down arrow key)
until the word RECAL appears.
Step 6: Press Enter.
Step 7: The gauge will now flash between INPUT and unit
of measure on the lower line and .00 on the top line. Apply
zero pressure to the gauge.
Step 8: Press Enter. Zero pressure is now set.
Step 9: The gauge will display full-scale pressure. Apply
full-scale pressure to the gauge.
Step 10: Press Enter. ull-scale pressure is now set.
Step 11: The gauge will now display mid-scale pressure.
Apply mid-scale pressure to the gauge.
Step 12: Press Enter. Mid-scale pressure is now set.
(ote: For compound ranges this recalibration is zero,
full-scale, mid-scale and full-vac.)
FOR FACTORY CA IBRATED SETINGS:
Step 13: To reinstate factory calibrated settings for zero,
full-scale and mid-scale press the (down arrow key)
Menu key until the word ACT appears.
Step 14: Press Enter. actory calibration settings are now
reinstated.
Step 15: After zero, full-scale and/or mid-scale or factory
default calibration have been set, the word SAVE appears
on the gauge display.
Step 16: Press Enter to finalize calibration.
MENU FUNCTIONS
*Indicates default.
I&M008-10136-DIG PDC 7-05_layput 8/4/11 2:42 PM Page 10
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Instrumento de medición de PRECISION DIGITAL
PRECISION DIGITAL
PRECISION DIGITAL PD6701 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL PD8-7000 Series Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL ProtEX-MAX PD8-7000 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Loop Leader PD683 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL pd663 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Helios PD2-6060 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL PD6800 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL vantageview Safe Touch PD6700 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL ProVu Series Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL DART PD602 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Trident PD765 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Loop Leader PD683 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Loop Leader PD683 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Loop Leader Series Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Protex Pro PD6801 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Sabre Series Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL ProtEX-RTP PD6830 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL NOVA PD560 Series Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL ProtEx Pro PD6800-0L1 Manual de usuario
PRECISION DIGITAL
PRECISION DIGITAL Helios PD2-6080 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario