PR Lighting XR330 Framing Manual de usuario

XR330 Framing

PR-2357

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/24

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS

STAND-ALONE MODE

MASTER/SLAVE MODE

OPERATION MENU 8

ERROR MESSAGES 13

REPLACING GOBOS 14

DMX PROTOCOL 15

LED INDICATION 18

MAINTENANCE 18

LUBRICATION 18

KEEPING THE PROJECTOR CLEAN 18

TROUBLESHOOTING 18

TECHNICAL DATA 19

ELECTRICAL DIAGRAM 22

COMPONENT ORDER CODES 23

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

unit are in good condition before installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and

/ or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR Signal Cable 1 Set with plug and socket

Safety cord 1 Pc

User’s manual 1 Pc

Ωclamps 2 Pcs Optional

When unpa

e any dam

The project

humidity an

The project

ventilation s

Do not proj

Avoid direct

Do not atte

Electrical co

Before insta

It is essentia

Do not conn

Make sure t

Only handle

Keep the la

The project

shown in “i

Shields and

example by

Exterior sur

There is no

removed.

If you have

Always d

work !

king and befo

ge caused by t

r is for indoor

dust. Do not

r is not design

r is only inten

r must be inst

ots are blocke

ct the beam on

exposure to th

pt to dismantl

nection must

lation, ensure t

that each proj

ct this device

at the powe

the powe

-cor

p clean. Do n

r should alwa

stalling the pro

lens shall be

racks or deep

ace temperatur

user servicea

ny questions o

sconnectio

e disposing of

ansportation, c

use only, IP20

llow contact w

d or intended t

ed for installa

lled in a loca

o infla

mable

light from the

and/or modif

nly be carried

at the voltage

ctor is correctl

o any other ty

ord is never cr

by the plug.

t touch the la

s be installed

ector” section.

hanged if the

cratches.

s of the lumin

le parts inside

suggestions,

from Po

E USAG

the carton che

nsult your de

Use only in d

th water or an

be mounted

n, operation a

ion with adeq

surfaces, mini

lamp. The ligh

the projector i

ut by qualifie

nd frequency

earthed and t

es of dimmer

mped or dam

ever pull out t

p glass with ba

ith a second

have become

ire after 30 mi

the projector,

on’t hesitate to

er, when th

3/24

OF TH

k there is no t

ler and do not

y locations. K

other liquids.

rectly on to in

d maintenanc

ate ventilation

um distance i

is harmful to t

any way.

personnel.

f power suppl

at electrical in

paratus.

ged by sharp e

e plug by tugg

e hand.

ry safety fixin

visibly damag

utes operation

do not open t

consult your d

device no

PROJE

ansportation d

se the apparat

ep this device

lammable surf

by qualified p

at least 50cm

3m.

e eye.

match the po

allation confo

ges. Never le

ng the powe

. A safety cor

d to such an

is 45℃, when

e housing an

aler or manuf

in use or

TOR

mage before

away from rai

ces.

rsonnel.

from adjacent

er requireme

ms to all relev

the power-cord

ord.

is suppli

d f

xtent that the

steady state is

never operat

cture

efore clean

sing the projec

and moistur

wall surfaces.

ts of the projec

nt standards.

come into conta

r this; it shoul

r effectiveness

chieved 60℃,

the projector

ingor any

or. Should the

, excessive he

Be sure

hat

or.

t with other cabl

be attached

is impaired, f

with the co

aintenan

4/24

INSTALL THE PROJECTOR

Safety Cord

Handle

Clamp

Digital

Control

Panel

Warning

Please run the safety cord

through two holes for safety.

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the projector is firmly

anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector

to is secure and strong enough to support the weight of a XR 1000 Framing

WARNING:

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times the Projector’s weight.

FITTING THE LAMP

Lock the yoke before

fitting/replacing

the lamp. Just as Shown by

Figure 1, after Opening the cover

at the rear of the projector by

loosening 8 fastfit screws, you can

open the head. To adjust the lamp

as per Figure 2. Take out the lamp

as per the figure 3.

Before lamp installation, tighten its

power wires well. Lamp in and

out are opposite orders

Note: don’t touch the internal

surface of the reflector and the

burner of the lamp with bare hands

so as not to impair the beam

output.

Important: Always read

"Instructions for use" enclosed

with the lamp.

1.open the fan after unfastening

four scews on both sides

of the fan.

2.use cross screw driver

to loosen the tightening

screw on one side of the lamp

2.Take the lamp out after pushing

it downward after removing two lamp

wires on its other side.

Figure2：lamp adjustment 3.use cross screw driver

to adjust two screws to adjust

the lamp's position

1.unfasten the tightening

screw on one side of the

lamp

Figure 1：8 pcs of fastfit screws Figure3：Removal of Lamp

5/24

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before connection with mains power, make sure that the voltage and frequency marked on the rating plate of the projector match what

are supplied. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation conforms to all

relevant standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The XR330Framing accepts digital control signals in

protocol DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

DMX Controller

DMX512

Input Output DMX teminator

Input Output Input

6/24

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

W-DMXDMX

Projector configuration can be set conveniently via push button and LCD display.

Launch the projector and press button ENTER for more than 2 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically.

TO SET THE DMX START ADDRESS

Each XR 330 Framing must be given a DMX start address so that the correct projector responds to the correct control signals. This

DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out

from the controller. The XR 330 Framing has 3 DMX modes. There are standard mode ,short mode and extended mode. For

example standard mode has 34channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 035, No. 3 projector’s

address 051, No. 4 projector’s address069, and so on.

Launch the projector. Press button ENTER more than 2seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

7/24

STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be set accordingly.

After Powered on, the group will run in Master/Slave Mode

Input Output DMX terminator

Master Slave Input

Input Output Input

8/24

OPERATION MENU

First Menu Secondary Menu Third Menu Fourth Menu

DMX Address DMX Address=XXX

Reset

Are You Sure

Config Settings

DMX Mode

Standard

Extended

Short

Lamp Control

By Control Channe

By Power On

By DMX Present

Loss of DMX

When DMX is Lost

Normal time out

When DMX is Lost

Hold Last Value

Fan Operate Mode

Normal

Fan Operate Mode

Quieter

Fan Operate Mode

Hot Environment

Factory Settings

(Press button

DOWN/UP/ENTER at the same

time to enter the sub-menu)

Fixture Type

(WARNING: Never change the fixture

type ,otherwise the system will be

damaged!)

Option Settings

Color Positions

STEPPED

Color Positions

LINEAR

F-Gobo Positions

STEPPED

F-Gobo Positions

LINEAR

Pan DMX Invert

OFF

Pan DMX Invert

Tilt DMX Invert

OFF

Tilt DMX Invert

Pan Tilt Swap

OFF

Pan Tilt Swap

Dimmer Invert

OFF

Dimmer Invert

Iris Invert

OFF

Iris Invert

9/24

Zoom Invert

OFF

Zoom Invert

CYM Invert

OFF

CYM Invert

Defaults

OFF

Defaults

Restore Defaults

Display Options

Display Mode

Display

On Always

Display

Off After Delay

Display Invert

OFF

Display Invert

Display Dimming

Disp Dim Level

Min

Disp Dim Level

Full

Display Contrast

XX(1~21)

Information

Lamp Hours Lamp Hours=

Reset Lamp Hours

Are You Sure(UP/DOWN)

Total Hours Total Hours=

Temperature

Display Board Display Board=

XX℃

Driver Board 1 Driver Board 1=

XX℃

Driver Board 2 Driver Board 2=

XX℃

Driver Board 3 Driver Board 3=

XX℃

Driver Board 4 Driver Board 4=

XX℃

Pan and Tilt Pan and Tilt=

XX℃

Head Sensor Head Sensor=

XX℃

Software Version Display Board Display Board=

X.X.X

10/24

Driver Board 1 Driver Board 1=

X.X.X

Driver Board 2 Driver Board 2=

X.X.X

Driver Board 3 Driver Board 3=

X.X.X

Driver Board 4

X.X.X

Pan and Tilt Pan and Tilt=

X.X.X

View DMX Values DMX Channel

1=XXX

Electronic SN Electronic SN=

************

RDM Device Label

ANSI E1.20 RDM

Version X.X

Pan Encoder

Wiring Normal

Pan Err 0

Count 50880

Tilt Encoder

Wiring Normal

Tilt Err 0

Count 28080

Driver Faults

X Over Temp 0

Y Over Temp 0

X Fault 0

Y Fault 0

Test Modes

Factory Setup

OFF

Factory Setup

Self Test

OFF

Self Test

Lamp Manual Control

Lamp Status

On Command Sent

S= X C= X

Lamp On

Turn Lamp On

Turn Lamp Off

Wireless Options

Wireless Mode

XLRFirst

Wireless Mode

Wireless Only

Wireless Mode

XLR Only

Wireless Mode

Wireless To XLR

Wireless Mode

Wireless First

Un-Link Wireless

Really Un-Link

Enter=Yes

Operation Mode

Operation Mod

DMX Mod

Operation Mode=

Master Mode

User’s Memory 1

User’s Memory 2

Preset Memory 1

Preset Memory 2

Tabla de contenidos

Otros manuales de Proyector de PR Lighting

PR Lighting

PR Lighting PR-3400D Manual de usuario

PR Lighting

PR Lighting PR5000 Manual de usuario

PR Lighting

PR Lighting XPar 336 Manual de usuario

PR Lighting

PR Lighting LSBAR 336 Manual de usuario

PR Lighting

PR Lighting PRO STAGE PR-3051 Manual de usuario

PR Lighting

PR Lighting XR 330 SPOT Manual de usuario

PR Lighting

PR Lighting XPar 1514 ZOOM Manual de usuario

PR Lighting

PR Lighting PRO-PAR Manual de usuario

PR Lighting

PR Lighting XR 1400 Spot Manual de usuario

PR Lighting

PR Lighting PRO-PAR D Manual de usuario

PR Lighting

PR Lighting XS 1200 Beam Manual de usuario

PR Lighting

PR Lighting XR380 BEAM Manual de usuario

PR Lighting

PR Lighting XLED 590 Manual de usuario

PR Lighting

PR Lighting AQUA 580 Manual de usuario

PR Lighting

PR Lighting PR-2720 Manual de usuario

PR Lighting

PR Lighting XRLED 700 Spot Manual de usuario

PR Lighting

PR Lighting XPar 360 PR-8955 Manual de usuario

PR Lighting

PR Lighting XLED 1037 PR-8120 Manual de usuario

PR Lighting

PR Lighting AQUA MARINE 580 BWS Manual de usuario

PR Lighting

PR Lighting XRLED 1800-W Framing Manual de usuario

PR Lighting

PR Lighting PR5000 Spot Manual de usuario

PR Lighting

PR Lighting XPar 360-W Manual de usuario

PR Lighting

PR Lighting Solo 1200 Guía

PR Lighting

PR Lighting XRLED 500 SPOT Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario