PR Lighting XPar 336 Manual de usuario

XPar 336

PR-8950

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/17

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

CONTROL SYSTEM AND POWER CONNECTIONS 4

DMX TERMINATOR 5

SETUP OPTIONS-PROJECTOR CONFIGURATION 5

TO SET THE DMX START ADDRESS 6

OPERATION MENU 7

DMX PROTOCOL 9

INDICATION OF LED DISPLAY 12

MAINTENANCE 12

TROUBLESHOOTING 12

TECHNICAL DATA 13

ELECTRICAL DIAGRAM 16

COMPONENT ORDER CODES 17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Barn door 1 Pc Optional

Safety cord 1 Pc

This manual 1 Pc

Signal cable 1 Pc Optional

3/17

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the optical system clean. Do not touch the LED lens with bare hands.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as

a secondary safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.

LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired,

for example by cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes operation is 45℃, when achieving steady state it is50℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/17

INSTALL THE PROJECTOR

When the projector is used, as the right figure above, unfold the support to certain angle and put the projector onto a

flat surface. Make sure it is steady.

When the projector is used at a high place, as the left figure above, fold the support, turn it round to the top of the

projector, connect a lamp hook to the mounting hole reserved in the support by screws, and then hang the hook to a high

place. Eventually, use the safety cord provided to pass through the handles and hang it as a second safety fixing.

CONTROL SYSTEM AND POWER CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 3- pin signal

input and output cables as connection. The 3-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The XPar 336 accepts digital control signals in protocol DMX512 (1990).

The amount of projectors connected in parallel is not more than 32. Connect the controller’s output to the first fixture’s

input cable with a 3-pin signal cable, connect the first fixture’s output cable to the second fixture’s input cable and connect

the rest fixtures in the same way. Eventually, connect the last fixture’s output cable to a DMX terminator. Note: Only when

all the start addresses of fixtures are set the same, synchronous control could be achieved.

When the first fixture is not connected to the controller, and all the other connections are the same as above, it is master /

slave mode connection. To achieve master / slave mode, set the first fixture master , the others salve( slave is default).

As for power connections, each projector has to be supplied separately by external power. Use the power cord of each

projector to connect the mains power directly, paying attention to the voltage and frequency marked on the panel of the

projector.

Lamp Hook Mounting Hole

Safety Cable

Support

FUNCTION

DMX IN

DMX OUT

GND

DATA +

DATA -

DMX512

5/17

All of the connections are as the figure below.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push-button switch and LED display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your

settings or enter the next menu. Press button UP or DOWN to change values(add or subtract)

Press button FUNC, it will return to the upper menu one by one or browse through the main menu.

DMX Controller

Power IN Power IN Power IN

DMX OUT DMX IN DMX OUT DMX IN XLR terminator

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

ENTERUP DOWN

FUNC

6/17

TO SET THE DMX START ADDRESS

Each Xpar336 must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. The Xpar336 have 3 DMX modes, which are standard mode，extended mode and

short mode. For example, the standard mode has 11 channels, so set the No. 1 projector’s address 001, No. 2

projector’s address 12, No. 3 projector’s address 23, No. 4 projector’s address 34, and so on.

Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.

Press button FUNC, UP or DOWN to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been

enabled.

Press button FUNC, it will return to the upper menu one by one.

7/17

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address)

XXX

（XXX:1~512）

CNFG

(Config settings)

dmX

(DMX mode)

STd

(Standard mode)

EXT

(Extended mode)

SHRT

(Short mode)

dISP

(Display settings)

OFF

(Shut off digital CRT without

pressing buttons in 5 minutes)

mORS

(Master /Slave Settings)

SLAV

(Slave)

mAST

(Master)

FACT

(Reset factory setup) yES

TRmd

(Transmit parameters) yES

INFO

(Information)

TImE

(Fixture usage time) XXXX

TEmP

(LED board temperature) XX

VER

(Version) X.X.X

TEST

(Test mode)

(red)

(green)

(blue)

(white)

RGb

(

ed/green/blue)

Rwb

(Red/white/blue)

RGbw

(

ed/green/blue/white)

(Operation mode)

dmx

(DMX mode)

PR XX

(Preset memory, PR01~PR16）

ET XX

(User memory,ET01~ET16）

COL1

(Colour 1)

(Number: 0~14)

COL2

(Colour 2)

(Number: 0~14)

COL3

(Colour 3)

(Number: 0~14)

COL4

(Colour 4)

(Number: 0~14)

Note:

1. When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the

master projector to the slave projectors in the following conditions, such as DMX channel mode, Display setting

status and operation mode (User memory data is included).

2. Projectors which receive Parameters transmitted shall be set slave automatically.

3. What “Number” in “ET XX” submenu represents refer to the following table

8/17

Number 0

3 4 5 6 7 8 9 10 11 12 13 14

Colour

RG RB RW G

GW B

RGB RG

RGB

Only when setting of “Number” submenu has been done and return to “ET XX” menu, corresponding colour effect

comes out. You can choose numbers from Group COL1 to COL4 separately to form a user memory.

9/17

DMX PROTOCOL

Short

mode

Standard

mode

Extended

mode FUNCTION DMX DESCRIPTION

1 1 1 Dimmer 000-255 Linear Dimming from dark to light

2 Dimmer Fine 000-255 Dimmer in 16 Bit precision

2 2 3 Colour Temperature

000 No effect

001-255 Colour temperature linear adjustment

from 3200K to 10000K

3 4 Macro Channel

000 No effect

001-015 Colour Temperature 3200K

016-031 Colour Temperature 5600K

032-047 Colour Temperature 7200K

048-063 Colour Temperature 10000K

064-079 Red

080-095 Green

096-111 Blue

112-127 Purple

128-143 Blue and White

144-159 Red and White

160-175 Green and White

176-191 White

192-207 Yellow and White

208-223 Purple and White

224-239 Effect 1

240-255 Effect 2

3 4 5 Red 000-255 Linear adjustment from dark to light

4 5 6 Green 000-255 Linear adjustment from dark to light

5 6 7 Blue 000-255 Linear adjustment from dark to light

6 7 8 White 000-255 Linear adjustment from dark to light

9 Hue 000-255 Hue selection

10 Saturation 000-255 Saturation from shallow to deep

11 Value 000-255 From dark to light

7 8 12 Strobe 000-009 No effect

010-255 Strobe speed from slow to fast

9 13 Preset memory

000 No effect

001-015 Preset memory 1

016-031 Preset memory 2

032-047 Preset memory 3

048-063 Preset memory 4

064-079 Preset memory 5

080-095 Preset memory 6

10/17

096-111 Preset memory 7

112-127 Preset memory 8

128-143 Preset memory 9

144-159 Preset memory 10

160-175 Preset memory 11

176-191 Preset memory 12

192-207 Preset memory 13

208-223 Preset memory 14

224-239 Preset memory 15

240-255 Preset memory 16

10 14 User Memory

000 No effect

001-015 User memory 1

016-031 User memory 2

032-047 User memory 3

048-063 User memory 4

064-079 User memory 5

080-095 User memory 6

096-111 User memory 7

112-127 User memory 8

128-143 User memory 9

144-159 User memory 10

160-175 User memory 11

176-191 User memory 12

192-207 User memory 13

208-223 User memory 14

224-239 User memory 15

240-255 User memory 16

11 15 Memory Speed

000 No effect

001-015 Speed 1,the fastest

016-031 Speed 2

032-047 Speed 3

048-063 Speed 4

064-079 Speed 5

080-095 Speed 6

096-111 Speed 7

112-127 Speed 8

128-143 Speed 9

144-159 Speed 10

160-175 Speed 11

176-191 Speed 12

192-207 Speed 13

208-223 Speed14

224-239 Speed 15

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de PR Lighting

PR Lighting

PR Lighting XR380 BEAM Manual de usuario

PR Lighting

PR Lighting XRLED 1800-W Framing Manual de usuario

PR Lighting

PR Lighting Solo 1200 Guía

PR Lighting

PR Lighting PR-2720 Manual de usuario

PR Lighting

PR Lighting LSBAR 336 Manual de usuario

PR Lighting

PR Lighting PRO-PAR Manual de usuario

PR Lighting

PR Lighting AQUA 580 Manual de usuario

PR Lighting

PR Lighting PR-3400D Manual de usuario

PR Lighting

PR Lighting XR 330 SPOT Manual de usuario

PR Lighting

PR Lighting PRO-PAR D Manual de usuario

PR Lighting

PR Lighting XRLED 700 Spot Manual de usuario

PR Lighting

PR Lighting PR5000 Spot Manual de usuario

PR Lighting

PR Lighting PRO STAGE PR-3051 Manual de usuario

PR Lighting

PR Lighting XPar 360-W Manual de usuario

PR Lighting

PR Lighting AQUA MARINE 580 BWS Manual de usuario

PR Lighting

PR Lighting PR5000 Manual de usuario

PR Lighting

PR Lighting XPar 360 PR-8955 Manual de usuario

PR Lighting

PR Lighting XLED 1037 PR-8120 Manual de usuario

PR Lighting

PR Lighting XR330 Framing Manual de usuario

PR Lighting

PR Lighting XR 1400 Spot Manual de usuario

PR Lighting

PR Lighting XRLED 500 SPOT Manual de usuario

PR Lighting

PR Lighting XPar 1514 ZOOM Manual de usuario

PR Lighting

PR Lighting XLED 590 Manual de usuario

PR Lighting

PR Lighting XS 1200 Beam Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario